3Com 4007R - Manual

3Com 4007R

3Com 4007R – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
Page: / 22

Table of Contents:

  • Page 3 – Quick Installation Guide
  • Page 4 – The Switch 4007R chassis must be installed, removed, or; Figure 1
  • Page 5 – Switch Setup Tasks; Figure 2; Setup Tasks for Switch 4007R 8-slot Chassis
  • Page 6 – Unpacking; Safety regulations state that the selected table, shelf, or rack
  • Page 7 – Figure 3; Contents of the Switch 4007R Chassis Shipping Box
  • Page 8 – Figure 4; Removing the Chassis Shipping Box; Remove the corrugated sleeve by pulling it straight up (Figure 4).
  • Page 9 – Figure 5; The Switch 4007R 8-slot Chassis is Shipped with These Slots Empty
  • Page 10 – Preinstallation; The rack-mount installation requires at least two people. Do
  • Page 11 – Location Requirements; Relative humidity is between 10 and 90 percent, noncondensing.; Before You Begin
  • Page 12 – Switch 4007R Getting Started Guide; Figure 6; Rack Types; Bolt the rack to the floor.
  • Page 13 – Selecting the Slot on the Rack
  • Page 14 – Figure 7; Using the Chassis Rack-mount Template; On some racks, the mounting shelf may not align easily to
  • Page 15 – To install the mounting shelves, follow these steps:; Figure 8; Slots on the Rack and Distances Between Each Slot; Insert a mounting shelf in the rack.; Alignment pin
  • Page 16 – Figure 9; Installing a Mounting Shelf into the Rack
  • Page 17 – Installing the Chassis; This section describes how to install the chassis:; Installing the Chassis in a Rack Without Clip Nuts; Prepare to lift the chassis.
  • Page 18 – Support the back of the chassis until the two bottom screws; Installing the Chassis in a Rack Using Rack-Mount Clip Nuts
  • Page 19 – Installing a Rack-mount Clip in the Rack; Rack rail
  • Page 20 – bottom; Installing the Chassis on a Table or Shelf; When you install the chassis on a table or shelf, do not use
  • Page 21 – Remove the four feet and the four screws from the hardware kit.; Attaching Plastic Feet to the Switch 4007R Chassis; Where to Go from
  • Page 22 – Locating 3Com; The
Loading the manual

http://www.3com.com/

Quick Installation Guide

For the 3Com Switch 4007R 8-slot Chassis

Part No. 10014099
Published February 2002

4007RQS.book Page 1 Friday, January 25, 2002 10:27 AM

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 3 - Quick Installation Guide

Quick Installation Guide For the 3Com Switch 4007R 8-slot Chassis Read this document before you attempt to install the 3Com Switch 4007R 8-slot chassis. This guide includes the following: ■ Switch Setup Tasks ■ Unpacking Instructions ■ Preinstallation Guidelines ■ Installing the Mounting Shelves ■ I...

Page 4 - The Switch 4007R chassis must be installed, removed, or; Figure 1

2 Quick Installation Guide This guide is intended for the system or network administrator who is responsible for installing and managing the network hardware. WARNING: The Switch 4007R chassis must be installed, removed, or replaced only by trained service personnel. Do not attempt to install, remov...

Page 5 - Switch Setup Tasks; Figure 2; Setup Tasks for Switch 4007R 8-slot Chassis

Quick Installation Guide 3 Switch Setup Tasks Figure 2 illustrates the tasks to perform to set up a Switch 4007R 8-slot chassis. Figure 2 Setup Tasks for Switch 4007R 8-slot Chassis ON R Switch 4007 1 2 3 4 5 6 7 8 9 10 Install the Chassis and Optional Devices • 4 Install a Power Supply and the Powe...

Other 3Com Models

All 3Com Other