Page 3 - Table of Contents
LTC 8600 | LTC 8800 Series | en iii Bosch Security Systems, Inc. Instruction Manual F.01U.127.393 | 2.0 | 2009.03 Table of Contents 1 Safety ..................................................................................................................................................... 1 2 Unpac...
Page 7 - Safety; Important Safety Instructions; Object and liquid entry -
LTC 8600 | LTC 8800 Series | 1 Bosch Security Systems, Inc. Instruction Manual F.01U.127.393 | 2.0 | 2009.03 1 Safety Important Safety Instructions Read, follow, and retain for future reference all of the following safety instructions. Heed all warnings on the unit and in the operating instructions ...
Page 8 - Damage requiring service -
2 | LTC 8600 | LTC 8800 Series F.01U.127.393 | 2.0 | 2009.03 Instruction Manual Bosch Security Systems, Inc. 11. Power sources - Operate the unit only from the type of power source indicated on the label. Before proceeding, be sure to disconnect the power from the cable to be installed into the unit...
Page 9 - Safety Precautions
LTC 8600 | LTC 8800 Series | 3 Bosch Security Systems, Inc. Instruction Manual F.01U.127.393 | 2.0 | 2009.03 Safety Precautions Important Notices Accessories - Do not place this unit on an unstable stand, tripod, bracket, or mount. The unit may fall, causing serious injury and/or serious damage to t...
Page 10 - Environmental statement -
4 | LTC 8600 | LTC 8800 Series F.01U.127.393 | 2.0 | 2009.03 Instruction Manual Bosch Security Systems, Inc. – Disconnect the unit's input connectors from outdoor equipment before disconnecting the grounding plug or grounding terminal. – Follow proper safety precautions such as grounding for any out...
Page 11 - SELV; Note
LTC 8600 | LTC 8800 Series | 5 Bosch Security Systems, Inc. Instruction Manual F.01U.127.393 | 2.0 | 2009.03 Power lines - Do not locate the camera near overhead power lines, power circuits, or electrical lights, nor where it may contact such power lines, circuits, or lights. SELV All the input/outp...
Page 12 - Disclaimer; Copyright
6 | LTC 8600 | LTC 8800 Series F.01U.127.393 | 2.0 | 2009.03 Instruction Manual Bosch Security Systems, Inc. destinées à fournir une protection raisonnable contre les interférences nuisibles quand l'appareil est utilisé dans une installation commerciale. Cette appareil génère, utilise et émet de l'e...
Page 13 - Customer Support and Service
LTC 8600 | LTC 8800 Series | 7 Bosch Security Systems, Inc. Instruction Manual F.01U.127.393 | 2.0 | 2009.03 Customer Support and Service If this unit needs service, contact the nearest Bosch Security Systems Service Center for authorization to return and shipping instructions. Service Centers USA R...
Page 15 - Unpacking
LTC 8600 | LTC 8800 Series en | 9 F.01U.127.393 | 2.0 | 2009.03 Instruction Manual Bosch Security Systems, Inc. 2 Unpacking This equipment should be unpacked and handled with care. If an item appears to have been damaged in shipment, notify the shipper. Verify that all parts shown in the Parts List ...
Page 16 - Service
10 | en LTC 8600 | LTC 8800 Series Bosch Security Systems, Inc. Instruction Manual F.01U.127.393 | 2.0 | 2009.03 3 Service If the unit needs repair, contact the nearest Bosch Security Systems Service Center for authorization to return and shipping instructions. Service Centers • USA • Repair Center ...
Page 17 - Description
LTC 8600 | LTC 8800 Series en | 11 F.01U.127.393 | 2.0 | 2009.03 Instruction Manual Bosch Security Systems, Inc. 4 Description These Allegiant video switcher/control systems combine both switching and com-puter technology to provide powerful performance and unique system features for the security us...
Page 19 - Allegiant Feature Summary Table
LTC 8600 | LTC 8800 Series en | 13 F.01U.127.393 | 2.0 | 2009.03 Instruction Manual Bosch Security Systems, Inc. 5 Allegiant Feature Summary Table These Allegiant Series systems are available in two (2) operating configurations: a base system and the base system with an optional PC based software pa...
Page 21 - System Components
LTC 8600 | LTC 8800 Series en | 15 F.01U.127.393 | 2.0 | 2009.03 Instruction Manual Bosch Security Systems, Inc. 6 System Components 6.1 LTC 8601 Series Systems • LTC 8601 Series Main CPU Bay A modular equipment bay which contains the system's microprocessor module (LTC 8610/01), the power supply mo...
Page 23 - System Accessory Components; IntuiKey Series KBD-Universal Keyboard
LTC 8600 | LTC 8800 Series en | 17 F.01U.127.393 | 2.0 | 2009.03 Instruction Manual Bosch Security Systems, Inc. 7 System Accessory Components The Allegiant Series accessory products provide many optional features to the base system. A brief description of accessory products is provided below. Compl...
Page 24 - LTC 8557 Series Keyboard Extension Kits
18 | en LTC 8600 | LTC 8800 Series Bosch Security Systems, Inc. Instruction Manual F.01U.127.393 | 2.0 | 2009.03 7.5 LTC 8555 Series Keyboards The LTC 8555 Series keyboards are compact, full function keyboards for use with Allegiant Series matrix switchers. LED readouts display real time system stat...
Page 25 - Units
LTC 8600 | LTC 8800 Series en | 19 F.01U.127.393 | 2.0 | 2009.03 Instruction Manual Bosch Security Systems, Inc. 7.10 LTC 8569, LTC 8570, LTC 8571, LTC 8572 Series Code Merger Units These series are control code merger and line driver units used to combine Allegiant biphase control code from two (up...
Page 27 - LTC 8850/00 Windows Based Graphical User Interface Software
LTC 8600 | LTC 8800 Series en | 21 F.01U.127.393 | 2.0 | 2009.03 Instruction Manual Bosch Security Systems, Inc. 7.19 LTC 8782 Series Code Translator Units The LTC 8782 Series code translators are accessory units that convert biphase code to other manufacturers’ control codes, or convert other manuf...
Page 28 - Virtual Allegiant Satellite Application Software
22 | en LTC 8600 | LTC 8800 Series Bosch Security Systems, Inc. Instruction Manual F.01U.127.393 | 2.0 | 2009.03 7.23.1 Integration Server The Integration Server is a versatile software package used to integrate multiple systems that are not ordinarily compatible with each other. These systems can i...
Page 29 - NOTE
LTC 8600 | LTC 8800 Series en | 23 F.01U.127.393 | 2.0 | 2009.03 Instruction Manual Bosch Security Systems, Inc. 7.24 LTC 8506/00 PC-to-Console Port RS-232 Cable The LTC 8506/00 is an RS-232 grade cable with 9-pin D-connectors on each end that is used to connect an Allegiant's system's console port ...
Page 34 - Installation Procedure; Main CPU Bay Installation; CAUTION; Video Input Modules
28 | en LTC 8600 | LTC 8800 Series Bosch Security Systems, Inc. Instruction Manual F.01U.127.393 | 2.0 | 2009.03 8 Installation Procedure 8.1 Main CPU Bay Installation Before discarding the shipping cartons, verify that the various pieces of equipment have no evidence of carrier damage. CAUTION Do n...
Page 35 - Video Output Modules
LTC 8600 | LTC 8800 Series en | 29 F.01U.127.393 | 2.0 | 2009.03 Instruction Manual Bosch Security Systems, Inc. being used, the modules should be inserted in a left-to-right manner so that the lower camera numbers are used first. Figure 5: Typical Video Input Module Insertion The VIMs are identical...
Page 36 - Camera and Monitor Video Connections; LTC 8600 Series and LTC 8800 Series Video Input Connections
30 | en LTC 8600 | LTC 8800 Series Bosch Security Systems, Inc. Instruction Manual F.01U.127.393 | 2.0 | 2009.03 Figure 7: Typical CPU Module Insertion If an LTC 8802 Series Monitor Expansion is supplied, it will contain an LTC 8816/01 Data Receiving Module in this slot. Install the main bay CPU or ...
Page 37 - Termination Practices
LTC 8600 | LTC 8800 Series en | 31 F.01U.127.393 | 2.0 | 2009.03 Instruction Manual Bosch Security Systems, Inc. eras, numbers 97 through 128) should be attached to the main bay connectors labeled “VIDEO 97-112” and “VIDEO 113-128.” Extra connectors are provided on the main bay for “looping” purpose...
Page 38 - LTC 8600 Series or LTC 8800 Series Video Input Terminations; IMPORTANT
32 | en LTC 8600 | LTC 8800 Series Bosch Security Systems, Inc. Instruction Manual F.01U.127.393 | 2.0 | 2009.03 8.6.1 LTC 8600 Series or LTC 8800 Series Video Input Terminations Each VIM card for an LTC 8600 Series or an LTC 8800 Series system has DIP switches for selecting the termination of each ...
Page 39 - LTC 8802 Series Monitor Expansion Bay Data Connections
LTC 8600 | LTC 8800 Series en | 33 F.01U.127.393 | 2.0 | 2009.03 Instruction Manual Bosch Security Systems, Inc. 8.6.3 LTC 8802 Series Monitor Expansion Bay Data Connections The LTC 8802 Series Monitor Expansion Bay is supplied with a 1 m (3 ft) data com-munication interconnect cable. Install this c...
Page 40 - Optional Accessories Installation; General Accessory Installation; Computer Interface Installation
34 | en LTC 8600 | LTC 8800 Series Bosch Security Systems, Inc. Instruction Manual F.01U.127.393 | 2.0 | 2009.03 9 Optional Accessories Installation 9.1 General Accessory Installation There are many accessory products available for the Allegiant Series, including key-boards, alarm interface units, c...
Page 42 - 0 Satellite Configuration Installations; Satellite Site “Trunk Line” Monitor Outputs
36 | en LTC 8600 | LTC 8800 Series Bosch Security Systems, Inc. Instruction Manual F.01U.127.393 | 2.0 | 2009.03 10 Satellite Configuration Installations Due to the many variations possible, only general guidelines can be covered for installing satellite systems. Refer to the Appendix Section of thi...
Page 43 - Main Site “Trunk Line” Video Inputs
LTC 8600 | LTC 8800 Series en | 37 F.01U.127.393 | 2.0 | 2009.03 Instruction Manual Bosch Security Systems, Inc. 10.2 Main Site “Trunk Line” Video Inputs At the main site, video trunk line connections coming from each of the remote site(s) should be connected (and properly terminated) using an avail...
Page 44 - Main Site Programming Requirements
38 | en LTC 8600 | LTC 8800 Series Bosch Security Systems, Inc. Instruction Manual F.01U.127.393 | 2.0 | 2009.03 Figure 11: Satellite Site Sample Program Showing Logical Camera Numbers and Titles To maintain a sense of order, it is preferable to program a satellite for a range of camera numbers. For...
Page 46 - Special Programming for “Cascaded” Satellite System
40 | en LTC 8600 | LTC 8800 Series Bosch Security Systems, Inc. Instruction Manual F.01U.127.393 | 2.0 | 2009.03 10.6 Special Programming for “Cascaded” Satellite System Configurations In a 3-tier cascaded satellite system, it is highly recommended for the system design to have more trunks lines bet...
Page 47 - Alarm Inputs in Satellite Systems
LTC 8600 | LTC 8800 Series en | 41 F.01U.127.393 | 2.0 | 2009.03 Instruction Manual Bosch Security Systems, Inc. 10.7 Alarm Inputs in Satellite Systems Any alarm inputs to the main site, which have been programmed to activate cameras located at satellites, will operate normally except when limited b...
Page 48 - 1 Feature Selection
42 | en LTC 8600 | LTC 8800 Series Bosch Security Systems, Inc. Instruction Manual F.01U.127.393 | 2.0 | 2009.03 11 Feature Selection Certain user-selectable features can provide enhanced Allegiant system operation capabilities. Any desired changes can be made now or delayed until specific system re...
Page 49 - 2 Main Power Connections
LTC 8600 | LTC 8800 Series en | 43 F.01U.127.393 | 2.0 | 2009.03 Instruction Manual Bosch Security Systems, Inc. 12 Main Power Connections 1. Attach the supplied AC power cord(s) between the bay(s) and appropriate AC power source. Verify that power supply is configured for desired voltage input. If ...
Page 51 - 3 Video Monitor Display; Extended Camera Title/Monitor Title
LTC 8600 | LTC 8800 Series en | 45 F.01U.127.393 | 2.0 | 2009.03 Instruction Manual Bosch Security Systems, Inc. 13 Video Monitor Display The Allegiant Series systems feature an integral text overlay with two or three rows of 24 characters each. There are over 2000 different characters that can be d...
Page 54 - Broadcast Message
48 | en LTC 8600 | LTC 8800 Series Bosch Security Systems, Inc. Instruction Manual F.01U.127.393 | 2.0 | 2009.03 13.2.10 Location 12 - Sequence Status Indication This location indicates the status of the sequence “active” in the monitor. There are four possible character combinations: a. ^ R indicat...
Page 55 - Video Loss Detection
LTC 8600 | LTC 8800 Series en | 49 F.01U.127.393 | 2.0 | 2009.03 Instruction Manual Bosch Security Systems, Inc. 13.6 Camera Number The left-most display on the top line shows the camera number. This number is gen-erated by the system and is always displayed. Each number is unique and identifies thi...
Page 56 - 4 Factory Default Settings; User Selectable DIP Switch Settings for Main CPU Bay
50 | en LTC 8600 | LTC 8800 Series Bosch Security Systems, Inc. Instruction Manual F.01U.127.393 | 2.0 | 2009.03 14 Factory Default Settings As the Allegiant system is shipped from the factory, certain features are placed in a default configuration. The installer can select some of these features at...
Page 61 - Middle Data Receiver DIP Switch S2
LTC 8600 | LTC 8800 Series en | 55 F.01U.127.393 | 2.0 | 2009.03 Instruction Manual Bosch Security Systems, Inc. 14.2.2 Middle Data Receiver DIP Switch S2 The lower DIP switch provides certain user-selectable options. These options are as follows: • Switch 1 of S2 This switch is reserved and should ...
Page 62 - 5 User Information; User Priority Levels
56 | en LTC 8600 | LTC 8800 Series Bosch Security Systems, Inc. Instruction Manual F.01U.127.393 | 2.0 | 2009.03 15 User Information 15.1 User Priority Levels There are eight (8) levels of user priority in the Allegiant system. Each of the 32 users in the Allegiant system has a default priority leve...
Page 63 - User Priority Access Table
LTC 8600 | LTC 8800 Series en | 57 F.01U.127.393 | 2.0 | 2009.03 Instruction Manual Bosch Security Systems, Inc. word can be changed using the keyboard (see User Function number 10). Refer to the specific section of the operation instructions for exact procedures of using key-board User Functions. A...
Page 64 - 6 Alarm Information; Basic Alarm Response Mode
58 | en LTC 8600 | LTC 8800 Series Bosch Security Systems, Inc. Instruction Manual F.01U.127.393 | 2.0 | 2009.03 16 Alarm Information 16.1 General The ability to automatically switch video in response to an external signal (usually a contact closure) is a necessary feature in any video switching sys...
Page 65 - Sample Alarm Responses
LTC 8600 | LTC 8800 Series en | 59 F.01U.127.393 | 2.0 | 2009.03 Instruction Manual Bosch Security Systems, Inc. 16.5 Alarm Activated Pre-position Alarm activated pre-position capability exists in each of the three (3) alarm response modes. This enables a pan/tilt/zoom equipped camera to automatical...
Page 67 - Alarm Relay Response
LTC 8600 | LTC 8800 Series en | 61 F.01U.127.393 | 2.0 | 2009.03 Instruction Manual Bosch Security Systems, Inc. 16.7 Alarm Relay Response Allegiant alarm responses include the ability to trigger isolated alarm relay outputs from an LTC 8540/00 Alarm Interface unit. An alarm output is typically used...
Page 68 - 7 Keyboard Operation
62 | en LTC 8600 | LTC 8800 Series Bosch Security Systems, Inc. Instruction Manual F.01U.127.393 | 2.0 | 2009.03 17 Keyboard Operation 17.1 General Primary operation of an Allegiant switcher is controlled via the system keyboard. The two types of keyboards currently available are: • Conventional LTC...
Page 69 - Switcher Commands; Controlling Camera Movement; Lock or Unlock Control of a Camera
LTC 8600 | LTC 8800 Series en | 63 F.01U.127.393 | 2.0 | 2009.03 Instruction Manual Bosch Security Systems, Inc. 17.2.2 Keyboard Log-off Procedure If the log-in feature has not been enabled, this action is not applicable. If the feature has been enabled, press: User Log-off [ User , then OFF ]. Any ...
Page 70 - Lock or Unlock Control of a Monitor
64 | en LTC 8600 | LTC 8800 Series Bosch Security Systems, Inc. Instruction Manual F.01U.127.393 | 2.0 | 2009.03 17.4.3 Lock or Unlock Control of a Monitor • When using IntuiKey keyboards, press [ Device Lockout] , located on the main Allegiant menu screen for these options. • With LTC 8555 Series k...
Page 72 - Sequence Control
66 | en LTC 8600 | LTC 8800 Series Bosch Security Systems, Inc. Instruction Manual F.01U.127.393 | 2.0 | 2009.03 17.5.2 Arm/Disarm All Alarms Press [ Alarm Control] , located on the main Allegiant menu screen to enter the menu screen containing these options. When using the IntuiKey keyboard: • To a...
Page 74 - Sequence Programming; Programming a Simple Camera Sequence
68 | en LTC 8600 | LTC 8800 Series Bosch Security Systems, Inc. Instruction Manual F.01U.127.393 | 2.0 | 2009.03 17.7 Sequence Programming 17.7.1 Programming a Simple Camera Sequence The Allegiant system has powerful sequencing capabilities. Using a system key-board, it is possible to enter sequence...
Page 75 - Sequence Function Summary
LTC 8600 | LTC 8800 Series en | 69 F.01U.127.393 | 2.0 | 2009.03 Instruction Manual Bosch Security Systems, Inc. mode, press Exit/Save [Prog] . Press Exit/Run [Run] , to exit the programming mode, store the sequence into memory, and start the sequence running. The switcher steps through the five (5)...
Page 76 - Programming a SalvoSwitching Camera Sequence
70 | en LTC 8600 | LTC 8800 Series Bosch Security Systems, Inc. Instruction Manual F.01U.127.393 | 2.0 | 2009.03 17.7.2 Programming a SalvoSwitching Camera Sequence A SalvoSwitching sequence can be used to switch a group of monitors simultane-ously as a synchronized group. To program a Salvo sequenc...
Page 77 - 8 Keyboard User Functions; General Information
LTC 8600 | LTC 8800 Series en | 71 F.01U.127.393 | 2.0 | 2009.03 Instruction Manual Bosch Security Systems, Inc. 18 Keyboard User Functions 18.1 General Information User functions are keyboard operations which are used infrequently, but provide important system options. NOTE: Certain functions are r...
Page 79 - User Function 1 - Local Keyboard Test
LTC 8600 | LTC 8800 Series en | 73 F.01U.127.393 | 2.0 | 2009.03 Instruction Manual Bosch Security Systems, Inc. User Function 1 - Local Keyboard Test User Function 1 can be used as a local test to ensure that all the keyboard LEDs and switches are working. This function automatically calibrates the...
Page 81 - User Function 8 - Set Date
LTC 8600 | LTC 8800 Series en | 75 F.01U.127.393 | 2.0 | 2009.03 Instruction Manual Bosch Security Systems, Inc. User Function 8 - Set Date User Function 8 enables the user to set the date displayed on all system monitors. If using the LTC 8555 Series keyboard, use the joystick to select the day, mo...
Page 84 - User Function 26 - Set Display Option On All Monitors; User Function 27 - Select Keyboard Log-in; User Function 29 - Reset RS-232 Parameters to Default
78 | en LTC 8600 | LTC 8800 Series Bosch Security Systems, Inc. Instruction Manual F.01U.127.393 | 2.0 | 2009.03 User Function 26 - Set Display Option On All Monitors This function is similar to User Function 6, except it selects the monitor display option of all monitors in the system. The User Fun...
Page 86 - User Function 38 - Printer Port Mode
80 | en LTC 8600 | LTC 8800 Series Bosch Security Systems, Inc. Instruction Manual F.01U.127.393 | 2.0 | 2009.03 User Function 38 - Printer Port Mode This function allows configuration of the system's PRINTER port for use with a LTC 8712 Series Console Port Expander accessory device. Move the joysti...
Page 87 - User Function 43 - CPU Battery Status
LTC 8600 | LTC 8800 Series en | 81 F.01U.127.393 | 2.0 | 2009.03 Instruction Manual Bosch Security Systems, Inc. diately be overridden by operators at the satellite location having any priority level. This situation is more likely to be encountered in 3-tier satellite systems that do not have a good...
Page 88 - User Function 45 – CPU Temperature Status; User Function 46 – Two/Three Line Titles
82 | en LTC 8600 | LTC 8800 Series Bosch Security Systems, Inc. Instruction Manual F.01U.127.393 | 2.0 | 2009.03 Some minor disturbance of the video images may be visible for 1 or 2 seconds while the cameras are being adjusted. If no changes are noticed, check to make sure that you have compatible d...
Page 89 - 9 Maintenance Information; Cleaning the Keyboard
LTC 8600 | LTC 8800 Series en | 83 F.01U.127.393 | 2.0 | 2009.03 Instruction Manual Bosch Security Systems, Inc. 19 Maintenance Information The Allegiant system has been designed to perform for long periods of time with lit-tle or no maintenance. Occasionally the need will arise to clean the keyboar...
Page 90 - AC Line Fuse Replacement; Power Supply Fuse Replacement; Replacement of Memory Backup Batteries
84 | en LTC 8600 | LTC 8800 Series Bosch Security Systems, Inc. Instruction Manual F.01U.127.393 | 2.0 | 2009.03 19.3 AC Line Fuse Replacement The AC line fuse on Allegiant power supply models is found on the rear of the equip-ment bay near the line cord connector. Power supply models for 220-240 VA...
Page 105 - 1 ERROR MESSAGES
LTC 8600 | LTC 8800 Series en | 99 F.01U.127.393 | 2.0 | 2009.03 Instruction Manual Bosch Security Systems, Inc. 21 ERROR MESSAGES • Error 01 - Invalid camera request The camera number entered from the keyboard does not exist. If using the optional LTC 8850 GUI Software or the optional LTC 8059 MCS,...
Page 107 - Warning Messages
LTC 8600 | LTC 8800 Series en | 101 F.01U.127.393 | 2.0 | 2009.03 Instruction Manual Bosch Security Systems, Inc. • Error 80 - Trunk not available An attempt was made to access a remote camera connected to a satellite sys-tem, but no unused trunk lines are currently available. Depending on system co...
Page 108 - 2 Troubleshooting Guide; Main Bay Checkout
102 | en LTC 8600 | LTC 8800 Series Bosch Security Systems, Inc. Instruction Manual F.01U.127.393 | 2.0 | 2009.03 22 Troubleshooting Guide The Allegiant system has been designed to perform reliably for long periods of time. All circuitry consists of state-of-the-art components designed around a modu...
Page 109 - Keyboard Checkout
LTC 8600 | LTC 8800 Series en | 103 F.01U.127.393 | 2.0 | 2009.03 Instruction Manual Bosch Security Systems, Inc. 22.2 Keyboard Checkout 1. No keyboard display indicators: Check interconnect cable for cut or broken wires between keyboard and main CPU bay. Replace cable if necessary. Relo-cate keyboa...
Page 110 - Remote Receiver/Driver Functions Inoperative
104 | en LTC 8600 | LTC 8800 Series Bosch Security Systems, Inc. Instruction Manual F.01U.127.393 | 2.0 | 2009.03 22.4 Remote Receiver/Driver Functions Inoperative 1. All receiver/drivers and functions inoperative: Verify power LED indicator on Signal Distribution Unit is lit. If not, check fuses on...
Page 111 - 3 GLOSSARY OF TERMS
LTC 8600 | LTC 8800 Series en | 105 F.01U.127.393 | 2.0 | 2009.03 Instruction Manual Bosch Security Systems, Inc. 23 GLOSSARY OF TERMS Auxiliary An auxiliary is an additional function of the remote receiver/driver which permits on/off control of outputs available to the user. In the Allegiant system...
Page 113 - Appendix A Satellite Systems
LTC 8600 | LTC 8800 Series en | 107 F.01U.127.393 | 2.0 | 2009.03 Instruction Manual Bosch Security Systems, Inc. Appendix A Satellite Systems A satellite system configuration is usually used for a medium to large distributed system, or to obtain extremely large matrix sizes configured more conventi...
Page 120 - Appendix B Installation Checklists
114 | en LTC 8600 | LTC 8800 Series Bosch Security Systems, Inc. Instruction Manual F.01U.127.393 | 2.0 | 2009.03 Appendix B Installation Checklists A simplified guide for those who are already familiar with installing and program-ming Allegiant systems. MAIN BAY HARDWARE INSTALLATION Unpack equipme...
Page 121 - Appendix C Quick Reference Cable Interconnections
LTC 8600 | LTC 8800 Series en | 115 F.01U.127.393 | 2.0 | 2009.03 Instruction Manual Bosch Security Systems, Inc. Appendix C Quick Reference Cable Interconnections C.1 Main Bay Video COAX-All video input and output connections to the Allegiant system should be made using a good grade of RG59U, RG6, ...
Page 122 - C.4 Signal Distribution Unit
116 | en LTC 8600 | LTC 8800 Series Bosch Security Systems, Inc. Instruction Manual F.01U.127.393 | 2.0 | 2009.03 C.4 Signal Distribution Unit CONNECTION TO MAIN BAY The Distribution unit is supplied with a 3 m long (10 ft) multiconductor cable with 9-pin D-type connectors. Power to the unit is prov...
Page 123 - Appendix D Main Bay Rear Panel Connector Pin-outs
LTC 8600 | LTC 8800 Series en | 117 F.01U.127.393 | 2.0 | 2009.03 Instruction Manual Bosch Security Systems, Inc. Appendix D Main Bay Rear Panel Connector Pin-outs Console Port RS-232 Pin-outs Pin # Designation 1 CHASSIS GND 2 Rx 3 Tx 4 CTS 5 RTS 6 NO CONNECTION 7 DATA GND 8 NO CONNECTION 9 NO CONNE...
