Bosch LR40G - User Manual - manualsarea.com

Page 2 - GlobalTestSupply; Find Quality Products Online at:

-2- MENU LR40G (1) (2) (3) (4) (5) (6) (7) (8) (a) (b) (c) (d) (e) (f)(g)(h)(i)(j) (10) (10) (10) (10) (10) (10) (9) (5) (14) (13) (12) (11) (9) (15) (16) (17) (18) (19) (20) www. GlobalTestSupply .com Find Quality Products Online at: [email protected]

Page 5 - Safety Symbols; LR40G General Safety Rules

-5- Safety Symbols The definitions below describe the level of severity for each signal word. Please read the manual and pay attention to these symbols. This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to ...

Page 6 - FCC Caution

-6- The manufacturer is not respon- sible for radio interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two condition...

Page 7 - Features

-7- The numbering of the product features shown refers to the illustration of the tool on the graphic page. (1) Laser beam reception area (2) “Laser beam over center line” LED direction indicator (3) LED for center line (4) “Laser beam below center line” LED direction indicator (5) Display (front an...

Page 9 - Intended Use; Inserting/Changing the Batteries; Battery charge indicator for; Assembly

-9- The laser receiver is intended to quickly find rotating laser beams of the wavelength specified in the technical data.The laser receiver is also intended for controlling the GRL4000-90CHVG via Bluetooth ® . The laser receiver is suitable for indoor and outdoor use. Intended Use Inserting/Changin...

Page 10 - Starting operation; Operation

-10- Starting operation u Protect the laser receiver against mois- ture and direct sunlight. u Do not subject the laser receiver to ex - treme temperatures or variations in tem- perature. As an example, do not leave it in vehicles for longer periods. In case of large variations in temperature, allow...

Page 11 - Settings

-11- center line” LED direction indicator (4) and the blue “laser beam above center line” LED direction indicator (2) briefly light up (even if the audio signal and/or LED direction indica- tors have been switched off). Laser receiver too low: If the laser beam hits the upper half of the reception a...

Page 12 - Functions

-12- cated on the display. At a low volume, the au- dio signal indicator (g) appears on the display with one bar; at a high volume, the indicator appears with three bars. When the audio sig- nal is switched off, the indicator goes out.Independent of the audio signal setting, a short beep sounds at l...

Page 14 - Practical Advice

-14- If the laser beam hits the reception area (1) at the height of the center line of the laser receiver, the center line indicator (h) and LOC is displayed on the text indicator. The Center- Lock symbol is displayed on the rotary laser on the start screen for the corresponding axis.In the event of...

Page 15 - Rectifying errors

-15- Rectifying errors Text display (e) Problem Corrective measure PNK Failed to estabish Bluetooth® connection to the rotary laser GRL4000-90CHVG Briefly press the on/off button on the rotary laser to close the error message. Restart the process for establishing the connection. If it is not possibl...

Page 16 - Maintenance and Service

-16- Store and transport the tool only in the supplied protective case.Check the tool each time before using.Keep the tool clean and dry at all times to ensure proper and safe operation.Do not immerse the tool into water or other fluids.Wipe off debris using a moist and soft cloth. Do not use any cl...

Bosch LR40G - User Manual

Table of Contents:

Summary

Other Bosch Models