BISSELL 61Z4 - Manual

16 w w w . b i s s e l l . c o m 5 the only tool you'll need to assemble your vacuum cleaner is a Phillips head screwdriver.1. Slide upper handle into lower handle by pushing forward. Insert two long screws into the holes marked with arrows and tighten both until snug. 2. Attach hose rack by placing...

16 w w w . b i s s e l l . c o m Transporting your vacuum Use the handle on the front to carry the vacuum or place the vacuum in the upright position and tip back to roll on the rear wheels. Releasing the power cord the upper and lower cord wraps rotate to allow for quick and easy removal of the pow...

16 w w w . b i s s e l l . c o m Using the tools 1 Make sure the vacuum is in the upright position. 2. Remove the hose from the hose base. This automatically diverts the suction to the hose. Unwrap the hose from the vacuum. 3. Use the hose alone or with the telescoping extension wand. Attach any of ...

16 w w w . b i s s e l l . c o m Emptying the dirt container Empty the dirt container as soon as the dirt reaches the “full” line on the side of the container.1. Press the release button on top of the carrying handle to remove the dirt container. 2. Choose an emptying method. Method #2 is recommende...

16 w w w . b i s s e l l . c o m Cleaning the dirt container additional steps can be taken to clean the dirt container as necessary.1. Ensure the dirt container has been emptied. 2. Remove the lower portion by pressing the front latch on the upper portion as shown. 3. Clean the screen with a cloth o...

16 w w w . b i s s e l l . c o m clearing clogs continued If suction is normal at the hose, follow these steps to check for and clear clogs for floor cleaning: 1. Check diverter area at back of machine for diverter position and clogs. When the hose wand is inserted in the base, the diverter should b...

16 w w w . b i s s e l l . c o m 14 M aintenance and care Brush reset If something becomes lodged in the foot and the rotating brush shuts off, turn the vacuum off and unplug from the outlet. Remove the obstruction. the brush will automatically reset when the cleaner is plugged in and turned back on...

16 w w w . b i s s e l l . c o m 16 T roubleshooting Vacuum cleaner won’t turn on Possible causes Remedies 1. Power cord not plugged in 1. Check electrical plug 2. Thermal protector activated 2. Allow cleaner to cool for 30 minutes, see pg. 13 3. Upper handle not fully attached 3. Remove upper handl...

16 w w w . b i s s e l l . c o m T roubleshooting 17 Vacuum cleaner is difficult to push Possible causes Remedies 1 . Incorrect height setting 1. Turn dial to higher setting Visible dust escaping from cleaner Possible causes Remedies 1. Filter door and/or gasket missing 1. Check filter door and gask...

16 w w w . b i s s e l l . c o m 18 B ISSELL Consumer Services If your bISSEll product should require service: In the uK, Australia or New Zealand, call BIssell Consumer services at the numbers below and we will give you the location of a BIssell Authorized service Center in your area. for all other...

16 w w w . b i s s e l l . c o m 19 Item Part no. Part name 1 48G7 hePA filter Cartridge 2 63m7 foam filter 3 203-1362 TurboBrush 4 203-1364 Telescoping Wand 5 203-1365 Combination Brush 6 203-1363 Crevice Tool 7 203-1382 Contour Tool 8 203-1485 hose 9 203-1469 light Bulb R eplacement parts 1 2 3 4 ...

16 w w w . b i s s e l l . c o m This warranty gives you specific legal rights, and you may also have other rights which may vary from country to country. If you need additional instruction regarding this warranty or have questions regarding what it may cover, please contact BIssell Consumer service...