BISSELL 61Z4 - Manuals

16 w w w . b i s s e l l . c o m 5 the only tool you'll need to assemble your vacuum cleaner is a Phillips head screwdriver.1. Slide upper handle into lower handle by pushing forward. Insert two long screws into the holes marked with arrows and tighten both until snug. 2. Attach hose rack by placing...

16 w w w . b i s s e l l . c o m Transporting your vacuum Use the handle on the front to carry the vacuum or place the vacuum in the upright position and tip back to roll on the rear wheels. Releasing the power cord the upper and lower cord wraps rotate to allow for quick and easy removal of the pow...

16 w w w . b i s s e l l . c o m Using the tools 1 Make sure the vacuum is in the upright position. 2. Remove the hose from the hose base. This automatically diverts the suction to the hose. Unwrap the hose from the vacuum. 3. Use the hose alone or with the telescoping extension wand. Attach any of ...

16 w w w . b i s s e l l . c o m Emptying the dirt container Empty the dirt container as soon as the dirt reaches the “full” line on the side of the container.1. Press the release button on top of the carrying handle to remove the dirt container. 2. Choose an emptying method. Method #2 is recommende...

16 w w w . b i s s e l l . c o m Cleaning the dirt container additional steps can be taken to clean the dirt container as necessary.1. Ensure the dirt container has been emptied. 2. Remove the lower portion by pressing the front latch on the upper portion as shown. 3. Clean the screen with a cloth o...

16 w w w . b i s s e l l . c o m clearing clogs continued If suction is normal at the hose, follow these steps to check for and clear clogs for floor cleaning: 1. Check diverter area at back of machine for diverter position and clogs. When the hose wand is inserted in the base, the diverter should b...

16 w w w . b i s s e l l . c o m 14 M aintenance and care Brush reset If something becomes lodged in the foot and the rotating brush shuts off, turn the vacuum off and unplug from the outlet. Remove the obstruction. the brush will automatically reset when the cleaner is plugged in and turned back on...

16 w w w . b i s s e l l . c o m 16 T roubleshooting Vacuum cleaner won’t turn on Possible causes Remedies 1. Power cord not plugged in 1. Check electrical plug 2. Thermal protector activated 2. Allow cleaner to cool for 30 minutes, see pg. 13 3. Upper handle not fully attached 3. Remove upper handl...

16 w w w . b i s s e l l . c o m T roubleshooting 17 Vacuum cleaner is difficult to push Possible causes Remedies 1 . Incorrect height setting 1. Turn dial to higher setting Visible dust escaping from cleaner Possible causes Remedies 1. Filter door and/or gasket missing 1. Check filter door and gask...

16 w w w . b i s s e l l . c o m 18 B ISSELL Consumer Services If your bISSEll product should require service: In the uK, Australia or New Zealand, call BIssell Consumer services at the numbers below and we will give you the location of a BIssell Authorized service Center in your area. for all other...

16 w w w . b i s s e l l . c o m 19 Item Part no. Part name 1 48G7 hePA filter Cartridge 2 63m7 foam filter 3 203-1362 TurboBrush 4 203-1364 Telescoping Wand 5 203-1365 Combination Brush 6 203-1363 Crevice Tool 7 203-1382 Contour Tool 8 203-1485 hose 9 203-1469 light Bulb R eplacement parts 1 2 3 4 ...

16 w w w . b i s s e l l . c o m This warranty gives you specific legal rights, and you may also have other rights which may vary from country to country. If you need additional instruction regarding this warranty or have questions regarding what it may cover, please contact BIssell Consumer service...

w w w . b i s s e l l . c o m A ssembly tool required: phillips screwdriver 1. Slide upper handle into lower handle by pushing forward. Insert two long screws into the holes marked with arrows and tighten both until snug. 2a. Attach hose rack by placing the rack over the center back portion of the v...

w w w . b i s s e l l . c o m O perations 6 transporting your vacuum use the handle on the front to carry the vacuum or place the vacuum in the upright position and tip back to roll on the rear wheels. Releasing the power cord the upper and lower cord wraps rotate to allow for quick and easy removal...

the rotating brush is turned on or off using the push button switch located below the power button switch on the top of the handle. the brush will start rotating when the unit is reclined. the brush should be on for most carpeted floors. you may want to turn the brush off for bare floor cleaning or ...

w w w . b i s s e l l . c o m 9 O perations emptying the dirt container empty the dirt container as soon as the dirt reaches the “full” line on the side of the container.1. Press the release button on top of the carrying handle to remove the dirt container. 2. Choose an emptying method. Method #2 is...

w w w . b i s s e l l . c o m M aintenance and care 10 cleaning the dirt container additional steps can be taken to clean the dirt container as necessary.1. Ensure the dirt container has been emptied. 2. Remove the lower portion by pressing the front latch on the upper portion as shown. 3. Clean the...

w w w . b i s s e l l . c o m 11 M aintenance and care Replacing the hepa filter cartridge the hepa filter cartridge should be replaced if machine performance is noticeably declining. More or less frequent replacing may be required based on individual vacuuming habits and types of debris picked up. ...

w w w . b i s s e l l . c o m 13 M aintenance and care 10. clearing clogs continued if suction is normal at the hose, follow these steps to check for and clear the clog for floor cleaning:10. Check the foot hose for clogs. If you are not able to tell from the outside if a clog is present, remove the...

w w w . b i s s e l l . c o m M aintenance and care 14 brush reset if something becomes lodged in the foot and the brush shuts off, turn the vacuum off and unplug from the outlet. Remove the obstruction. the brush will automatically reset when the cleaner is plugged in and turned back on.if the vacu...

w w w . b i s s e l l . c o m 15 M aintenance and care changing the light bulb 1. Turn power switch off. 2. Unplug vacuum from electrical outlet. 3. Recline handle for easier access to light bulb and remove 2 screws to lift off lens. 4. Remove the bulb by grasping bulb and pulling straight out of th...

w w w . b i s s e l l . c o m T roubleshooting 16 Vacuum cleaner won’t turn on possible causes Remedies 1. Power cord not plugged in 1. Check electrical plug 2. Blown fuse/tripped breaker 2. Check/replace fuse or reset breaker 3. Thermal protector activated 3. Allow cleaner to cool for 30 minutes, (...

w w w . b i s s e l l . c o m 17 T roubleshooting Vacuum cleaner is difficult to push possible causes Remedies 1. Incorrect height setting 1. Turn dial to higher setting Visible dust escaping from cleaner possible causes Remedies 1. Filter door and or gasket missing 1. Check filter door and gasket o...

w w w . b i s s e l l . c o m R eplacement parts - BISSELL vacuum 18 you may purchase parts from your retailer, by calling bissell consumer services or by visiting our website. below is a list of com- mon replacement parts*. While not all of these parts may have come with your specific model, they a...

w w w . b i s s e l l . c o m 19 W arranty - BISSELL Healthy Home Vacuum ™ This warranty gives you specific legal rights, and you may also have other rights which may vary from country to country. If you need additional instruction regarding this warranty or have questions regarding what it may cove...

©2011 BISSELL Homecare, Inc Grand Rapids, Michigan All rights reserved. Printed in China Part Number 110-4389 Rev 6/11 Visit our website at: www.bissell.com B ISSELL consumer services w w w . b i s s e l l . c o m 0 20 if your bissell product should require service: Call BISSELL Consumer Services at...