BILLY GOAT 350397 - Manual
BILLY GOAT 350397 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – - 2 - Form No F102207B
- Page 3 – - 3 - Form No F102207B; ADJUSTING SEED RATE
- Page 4 – - 4 - Form No F102207B; REPLACING SLICING REEL; Note; item
POWER RAKE SEEDER BOX KIT-350395 AND 350397
Part No 350398
- 1 - Form No F102207B
Seeder Box Installation:
1. Disconnect spark plug wire.
2. Support Power Rake on blocks to lift left front wheel off ground.
3. Remove 4 screws from front of machine.
4. Remove left front wheel.
5. Install seeder box to front of machine with four 5/16” x 3/4 cap screws,
4 flat washers, and 4 lock washers. Do not tighten at this time (see figure
1).
Wheel:
1. Slide the pulley on until it rests firmly against the hub.
2. Tighten two setscrews.
3. Be sure 3 washers (item 31) are on the axle, slip the belt (item 24) in
the groove on the pulley and slide wheel on the axle.
4. Secure with lock nut (item 35).
NOTE:
Replace thick locknut with the thin nut provided in parts bag.
New units are provided with thin nuts.
Belt alignment:
1. Attach the belt onto the seeder box pulley by turning the wheel and
slowly feeding the belt onto the seeder box pulley.
2. Rotate wheel to insure belt turns freely
3. If the belt seems to be too tight, bump seeder box upward to loosen
belt.
4. Check the pulley alignment then tighten 4 capscrews inside seeder
box.
5.Repeat step 3 to 5 if necessary
6. Remove blocks from under machine & push machine to test
mechanism.
Seeder meter control box installation:
1. Attach the Seed drop control box (Item 2) to the upper handle with the
hardware from the parts bag (Items 17, 28, 35, 36, 39, 40) using a 7/16”
and a 9/16” wrench. Then attach the cable to the bail with hardware items
42 and 43 using 5/16” and a 3/8” wrenches. Secure the cable with a ty-
wrap (item 44) to the upper handle.
2. Reconnect spark plug wire.
PURPOSE: To overseed an existing lawn or start a new lawn.
Tools Required: 3/16" allen wrench, 7/16”, 1/2", 5/8", 3/4", 9/16”, 5/16”, 3/8” wrench, Wood blocks or suitable support for
machine.
NOTE:
Older models with no holes will need additional tools:
3/8" drill bit and drill, center punch, two 1/2" wrenches.
INSTALLATION
Fig. 1
Fig. 2
Fig. 3
Fig. 4
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
POWER RAKE SEEDER BOX KIT-350395 AND 350397 Part No 350398 - 2 - Form No F102207B PARTS BAG SEEDER BOX KIT 350396 17 8160001 NUT LOCK 1/4 1 20 8177011 WASHER LOCK 5/16 4 23 8041026 SCREW CAP 5/16-18 x 3/4 4 27 8172020 WASHER 5/16 FENDER 4 28 8172007 WASHER 1/4 SAE 1 31 8171006 WASHER 1/2 FC 3 32 816...
POWER RAKE SEEDER BOX KIT-350395 AND 350397 Part No 350398 - 3 - Form No F102207B ADJUSTING SEED RATE LAWN PREPARATION - MOW LAWN TO LOWEST SETTING ON YOUR MOWER. - DO NOT WATER PRIOR TO SEEDING. - POWER RAKE TO DETHATCH LAWN AND REMOVE THATCH. - FERTILIZE LAWN WITH BROADCAST SPREADER. LAWN PREPARAT...
POWER RAKE SEEDER BOX KIT-350395 AND 350397 Part No 350398 - 4 - Form No F102207B REPLACING SLICING REEL To replace the current reel with a slicing reel it will take approx. 20 min. and requires 1/2" and 9/16" sockets, and a ratchet with extension. Use these instructions in conjunction with ...
