Page 3 - TABLE OF CONTENTS
TABLE OF CONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2Assembling Your Drive Enclosure . . . . . . . . . . . . . . . . . . . . . . . . .3Driver Installation...
Page 5 - INTRODUCTION
The Hi-Speed USB 2.0 External Drive Enclosure (the External Drive) isa portable compact storage drive that incorporates the USB 2.0(Universal Serial Bus 2.0) high-speed interface. The External Driveprovides a fast and easy way to add more storage space to yourcomputer. The Plug-and-Play feature give...
Page 6 - SYSTEM REQUIREMENTS; Hardware; Notebook and desktop computer with USB 1.0 or USB 2.0 port; Operating System; Windows
SYSTEM REQUIREMENTS 2 Hardware Notebook and desktop computer with USB 1.0 or USB 2.0 port Operating System Windows ® 98 SE, Me, 2000, or XP P74080-em-F5U209-man_9-02.qxd 9/19/02 3:05 PM Page 2
Page 7 - ASSEMBLING YOUR DRIVE ENCLOSURE; Remove top of the External Drive.
En ASSEMBLING YOUR DRIVE ENCLOSURE 1. Remove top of the External Drive. 2. If you are installing a 3 1 / 2 -inch hard drive, check to make sure your drive is set to “Master” (see jumper settinginformation printed on top of your disk drive), thenconnect the 34-position data cable and 4-positionpower ...
Page 8 - There are four fine-threaded screws, and four
ASSEMBLING YOUR DRIVE ENCLOSURE 4 Note: There are four fine-threaded screws, and four course-threaded screws included with your Hi-Speed ExternalDrive Enclosure Kit. Be sure to choose the screws that matchthe mounting holes for your drive. Do not try to force a course-threaded screw into a fine-thre...
Page 10 - If you are using Windows 98 or 98 SE, DO
ASSEMBLING YOUR DRIVE ENCLOSURE 6 8. Insert the mounting tabs on the free end of the front panelinto the second side rail, and hook the side rail onto thefront of the External Drive. 9. Finish the assembly by pressing the rail into the sixrectangular mounting holes in the side of the External Drive....
Page 11 - maximum USB bandwidth will be 12 Mbps.
En ASSEMBLING YOUR DRIVE ENCLOSURE 10. Plug the square-shaped connector of the USB cable intothe USB port on the rear panel of the External Drive. 11. Plug the rectangular-shaped connector of the USB cable into a Hi-Speed USB 2.0 port on your computer orHi-Speed USB 2.0 hub. You may also connect the...
Page 12 - DRIVER INSTALLATION; Insert the installation CD into your CD-ROM drive.
DRIVER INSTALLATION 8 Windows 98 SE 1. Insert the installation CD into your CD-ROM drive. 2. Open the Install CD. 3. Run the “TPPINST.EXE” to install the drivers for yourUSB 2.0 External Drive. 4. An installer dialog box appears. Click “Next”. 5. Choose “Complete” and click “Next”. 6. You may now co...
Page 13 - If the new drive does not appear in My Computer, you
En DRIVER INSTALLATION Note: If the new drive does not appear in My Computer, you may need to partition and format the drive. Please refer to the“Format the USB 2.0 External Drive” section to prepare yourUSB 2.0 hard disk drive. A green “Unplug or Eject Hardware” icon will appear in the system tray....
Page 14 - Select the “USB Mass Storage Device” then click “Stop”.
SAFE REMOVAL OF THE USB DISK FROM WINDOWS 10 Windows 98 1. Click the green “Unplug or Eject Hardware” icon in thesystem tray and select the device that you want to remove. 2. When the system prompts “You may safely remove thisdevice”, unplug the USB cable from the USB port of your computer. Windows ...
Page 15 - FORMAT THE USB 2.0 EXTERNAL DRIVE; Format under Windows 98/Me; Boot-up the computer into the Windows operating system.; Control Panel Method; Click “Start” and choose “Setting”.
En FORMAT THE USB 2.0 EXTERNAL DRIVE Format under Windows 98/Me 1. Boot-up the computer into the Windows operating system. 2. Plug in your External Drive. There are two methods to partition and format yourUSB 2.0 hard disk drive. Control Panel Method 1. Click “Start” and choose “Setting”. 2. Choose ...
Page 16 - Your removable hard drive is now ready for use.
FORMAT THE USB 2.0 EXTERNAL DRIVE 12 5. Select “Disk Drives”. Your new hard disk will appear in thehard drive list (in this case as “Toshiba 1924FCV”). 6. Double-click on the entry for your hard drive. Select“Settings”. The following screen will appear. 7. Make sure there are check marks in the “Dis...
Page 17 - DOS Method (Recommended for Advanced Users Only)
En FORMAT THE USB 2.0 EXTERNAL DRIVE DOS Method (Recommended for Advanced Users Only) 1. Click on “Start”, and choose “Programs”. Select “MSDOS”. 2. At the DOS prompt, type “FDISK” and press “Enter”. Note: If the FDISK utility terminates without displaying an error message, exit back to Windows and ...
Page 18 - IMPORTANT
FORMAT THE USB 2.0 EXTERNAL DRIVE 14 IMPORTANT Be sure that you select option 5 and change the “Current Fixed Disk” from “Disk 1” to the disk number assigned to yourExternal Drive. If your computer is equipped with only oneinternal drive, your new External Drive will be identified as“Disk 2”. If you...
Page 19 - If you are viewing the Control Panel in classic mode,
En FORMAT THE USB 2.0 EXTERNAL DRIVE Note: If you are viewing the Control Panel in classic mode, proceed directly to “Administrative Tools”. 2. Click on “Disk Management”. All connected disk drives willbe displayed in the lower right-hand corner of the“Computer Management” window. Information regard...
Page 20 - INFORMATION; FCC Statement
INFORMATION FCC Statement DECLARATION OF CONFORMITY WITH FCC RULES FOR ELECTROMAGNETIC COMPATIBILITY We, Belkin Corporation, of 501 West Walnut Street, Compton, CA 90220,declare under our sole responsibility that the product: F5U209 to which this declaration relates:Complies with Part 15 of the FCC ...
Page 23 - SOMMAIRE
SOMMAIRE Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1Configuration requise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2Montage du boîtier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3Installation du pil...
Page 26 - CONFIGURATION REQUISE; Matériel
2 CONFIGURATION REQUISE Matériel Bloc-notes et ordinateur de bureau équipé d’un port USB 1.0ou USB 2.0 Système d'exploitation Windows ® 98 SE, Me, 2000, ou XP P74080-em-F5U209-man_9-02.qxd 9/19/02 3:05 PM Page 2
Page 27 - MONTAGE DU BOÎTIER; Enlevez le couvercle du lecteur externe.
MONTAGE DU BOÎTIER 3 1. Enlevez le couvercle du lecteur externe. 2. Si vous installez un disque dur de 3 _ pouces, vérifiez quele cavalier du disque est positionné sur « Master » (voirl’information concernant le réglage du cavalier qui figuresur le couvercle du lecteur). Connectez le câble dedonnées...
Page 28 - le kit du boîtier externe High Speed comprend
Remarque : le kit du boîtier externe High Speed comprend quatre vis à filetage fin et quatre vis à filetage épais. Choisissezles vis adaptées aux trous de montage du lecteur. N’essayezpas de faire rentrer une vis à filetage épais dans un trou àfiletage fin. 5. Remettez le couvercle en place et vérif...
Page 30 - Remarque importante :
6 MONTAGE DU BOÎTIER 8. Insérez les onglets de l’extrémité libre du cache dans lesecond rail latéral et encliquetez le rail latéral à l’avantdu lecteur externe. 9. Terminez le montage en enfonçant le rail dans les sixtrous de montage rectangulaires situés sur le côté dulecteur externe. Remarque impo...
Page 31 - en cas de connexion à un port USB 1.1 Full Speed,
Fr MONTAGE DU BOÎTIER 10. Branchez le connecteur carré du câble USB sur le port USBsitué à l’arrière du lecteur externe. 11. Branchez le connecteur rectangulaire du câble USB sur leport USB 2.0 High Speed de l’ordinateur ou le hub USB 2.0High Speed. Vous pouvez également connecter le câble àun port ...
Page 32 - INSTALLATION DU PILOTE; Insérez le CD d’installation dans votre lecteur de CD-ROM.
8 INSTALLATION DU PILOTE Windows 98 SE 1. Insérez le CD d’installation dans votre lecteur de CD-ROM. 2. Ouvrez le CD Install. 3. Exécutez le fichier « TPPINST.EXE » pour installer les pilotesde votre lecteur externe USB 2.0. 4. Une boîte de dialogue d’installation apparaît. Cliquez sur « Suite ». 5....
Page 34 - RETRAIT DU DISQUE USB DE WINDOWS
10 RETRAIT DU DISQUE USB DE WINDOWS Windows 98 1. Cliquez sur l’icône « Débrancher ou éjecter le matériel » dela barre d’état système et sélectionnez le périphérique quevous voulez supprimer. 2. Quand le système affiche le message d’invite « Vous pouvezenlever ce périphérique », débranchez le câble ...
Page 35 - FORMATAGE DU LECTEUR EXTERNE USB 2.0; Formatage sous Windows 98/Me; Démarrez l’ordinateur sous Windows.; Méthode du Panneau de configuration; Cliquez sur « Démarrer » et choisissez « Paramètres ».
Fr FORMATAGE DU LECTEUR EXTERNE USB 2.0 Formatage sous Windows 98/Me 1. Démarrez l’ordinateur sous Windows. 2. Branchez votre lecteur externe. Il y a deux méthodes possibles de partitionnement et deformatage du lecteur de disque dur USB 2.0. Méthode du Panneau de configuration 1. Cliquez sur « Démar...
Page 36 - Votre disque dur amovible est prêt à l’emploi.
12 FORMATAGE DU LECTEUR EXTERNE USB 2.0 5. Sélectionnez « Lecteurs de disques ». Votre nouveau disquedur s’affichera dans la liste des lecteurs de disques durs (ils’agit dans ce cas de « Toshiba 1924FCV »). 6. Cliquez deux fois sur le nom du disque dur. Sélectionnez «Paramètres ». L’écran suivant s’...
Page 37 - À l’invite DOS, tapez « FDISK » et appuyez sur « Entrée ».
Fr FORMATAGE DU LECTEUR EXTERNE USB 2.0 Méthode DOS (recommandée pour les utilisateursavancés seulement) 1. Cliquez sur « Démarrer » et choisissez « Programmes ».Sélectionnez « MSDOS ». 2. À l’invite DOS, tapez « FDISK » et appuyez sur « Entrée ». Remarque : si l’utilitaire FDISK s’exécute jusqu’à l...
Page 38 - dans Windows XP, cliquez sur « Démarrer »,
14 FORMATAGE DU LECTEUR EXTERNE USB 2.0 IMPORTANT Veillez à bien sélectionner l’option 5 et à modifier le numéro du« Disque dur en cours » en remplaçant « Disque 1 » par lenuméro de disque affecté à votre lecteur externe. Si votreordinateur est équipé d’un seul disque interne, votre nouveaulecteur e...
Page 39 - si vous visualisez le Panneau de configuration en
Fr FORMATAGE DU LECTEUR EXTERNE USB 2.0 Remarque : si vous visualisez le Panneau de configuration en mode classique, passez directement à l’option « Outilsd’administration ». 2. Cliquez sur « Gestion des disques ». Tous les lecteurs dedisques connectés s’afficheront dans l’angle inférieur droit dela...
Page 40 - Déclaration FCC
16 INFORMATION Déclaration FCC DÉCLARATION DE CONFORMITÉ AVEC LA RÉGLEMENTATION FCC CONCERNANT LA COMPATIBILITÉ ÉLECTROMAGNÉTIQUE Nous, Belkin Corporation, sis à 501 West Walnut Street, Compton, CA 90220,déclarons sous notre entière responsabilité que le produit : F5U209 auquel se rapporte cette déc...
Page 43 - INHALTSVERZEICHNIS
De INHALTSVERZEICHNIS Einführung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1Systemanforderungen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2Zusammenbau Ihres Laufwerkgehäuses . . . . . . . . . . . . . . . . . . . .3Installation des Treib...
Page 45 - EINFÜHRUNG
De Das externe Laufwerkgehäuse für USB 2.0 Hi-Speed ist ein tragbareskompaktes Speicherlaufwerk mit einer Schnittstelle für USB 2.0 Hi-Speed. Das externe Laufwerk bietet einen schnellen und einfachenWeg für zusätzlichen Speicherplatz für Ihren Computer. Die Plug-and-Play-Funktion ist auf Reisen sehr...
Page 46 - SYSTEMANFORDERUNGEN
2 SYSTEMANFORDERUNGEN Hardware Notebook und Desktop-Computer mit USB 1.0 oderUSB 2.0 Anschluss Betriebssystem Windows ® 98 SE, Me, 2000, oder XP P74080-em-F5U209-man_9-02.qxd 9/19/02 3:06 PM Page 2
Page 47 - ZUSAMMENBAU IHRES LAUFWERKGEHÄUSES; Entfernen Sie die Oberseite des externen Laufwerks.
De ZUSAMMENBAU IHRES LAUFWERKGEHÄUSES 1. Entfernen Sie die Oberseite des externen Laufwerks. 2. Wenn Sie ein 3,5-Zoll-Laufwerk einbauen, müssen Siesicherstellen, dass Ihr Laufwerk auf „Master“ eingestellt ist(siehe aufgedruckte Jumper-Einstellungsinformation aufder Oberseite Ihres Laufwerks), und da...
Page 48 - Im Bausatz für Ihr externes Hi-Speed-Laufwerkgehäuse
ZUSAMMENBAU IHRES LAUFWERKGEHÄUSES Hinweis: Im Bausatz für Ihr externes Hi-Speed-Laufwerkgehäuse sind vier Feingewindeschrauben und vierGrobgewindeschrauben enthalten. Stellen Sie sicher, dass Siedie Schrauben auswählen, die zu den BefestigungsbohrungenIhres Laufwerks passen. Versuchen Sie nicht, ei...
Page 50 - Wenn Sie Windows 98 oder 98 SE
6 ZUSAMMENBAU IHRES LAUFWERKGEHÄUSES 8. Führen Sie die Kontaktnasen am losen Ende der Frontblendein die zweite Seitenstrebe und haken Sie die Seitenstrebenvorn am externen Laufwerk ein. 9. Machen Sie mit dem Zusammenbau weiter, indem Sie dieStrebe in die sechs rechteckigen Befestigungslöcher in derS...
Page 51 - Die maximale USB-Bandbreite im Falle eines
ZUSAMMENBAU IHRES LAUFWERKGEHÄUSES 7 10. Stecken Sie den quadratischen Stecker des USB-Kabels inden USB-Anschluss auf der Rückwand des externenLaufwerks. 11. Stecken Sie den rechteckigen Stecker des USB-Kabels inden USB-Anschluss für USB 2.0 Hi-Speed an IhremComputer oder an Ihrem Hub für USB 2.0 Hi...
Page 52 - INSTALLATION DES TREIBERS; Ein Installationsdialogfeld erscheint. Klicken Sie auf „Weiter“.
8 INSTALLATION DES TREIBERS Windows 98 SE 1. Legen Sie die Installations-CD in Ihr CD-ROM-Laufwerk. 2. Öffnen Sie die Installations-CD. 3. Führen Sie „TPPINST.EXE“ aus, um die Treiber für Ihrexternes Laufwerk für USB 2.0 zu installieren. 4. Ein Installationsdialogfeld erscheint. Klicken Sie auf „Wei...
Page 55 - Formatieren unter Windows 98/Me; Fahren Sie den Computer im Windows Betriebssystem hoch.; Methode Systemsteuerung; Klicken Sie auf „Start“ und wählen Sie „Einstellungen“.
FORMATIEREN DES EXTERNEN USB 2.0 LAUFWERKS 11 Formatieren unter Windows 98/Me 1. Fahren Sie den Computer im Windows Betriebssystem hoch. 2. Stecken Sie Ihr externen Laufwerk ein. Sie können Ihre Festplatte für USB 2.0 auf zwei Artenpartitionieren und formatieren. Methode Systemsteuerung 1. Klicken S...
Page 56 - Ihre Wechselplatte ist jetzt betriebsbereit.
12 FORMATIEREN DES EXTERNEN USB 2.0 LAUFWERKS 5. Wählen Sie „Laufwerke“. Ihre neue Festplatte erscheint inder Festplattenliste (in diesem Fall als „Toshiba 1924FCV“). 6. Doppelklicken Sie auf dem Eintrag für Ihre Festplatte.Wählen Sie „Einstellungen“. Der folgende Bildschirm erscheint: 7. Stellen Si...
Page 57 - Wenn das FDISK-Dienstprogramm ohne Anzeige einer
FORMATIEREN DES EXTERNEN USB 2.0 LAUFWERKS 13 DOS-Methode (nur für Fortgeschrittene) 1. Klicken Sie auf „Start“ und wählen Sie „Programme“. Wählen Sie „MSDOS“. 2. Auf die DOS-Aufforderung tippen Sie „FDISK“ ein unddrücken „Eingabe“. Hinweis: Wenn das FDISK-Dienstprogramm ohne Anzeige einer Fehlermel...
Page 58 - WICHTIG; In Windows XP klicken Sie auf „Start“, wählen
14 FORMATIEREN DES EXTERNEN USB 2.0 LAUFWERKS WICHTIG Stellen Sie sicher, dass Sie Option 5 wählen und ändern Sie die„Derzeitiges Festplatte“ von „Festplatte 1“ auf dieFestplattennummer Ihres externen Laufwerks. Wenn IhrComputer nur mit einem internen Laufwerk ausgestattet ist, istIhr neues externes...
Page 60 - KONFORMITÄTSERKLÄRUNG MIT FCC-RICHTLINIEN FÜR
16 INFORMATION FCC-Erklärung KONFORMITÄTSERKLÄRUNG MIT FCC-RICHTLINIEN FÜR ELEKTROMAGNETISCHE KOMPATIBILITÄT Wir, Belkin Corporation, in 501 West Walnut Street, Compton, CA 90220, USA,erklären in eigener Verantwortung, dass dieses Produkt: F5U209 auf das sich diese Erklärung bezieht,mit Abschnitt 15...
Page 63 - INHOUDSOPGAVE
Ne INHOUDSOPGAVE Inleiding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1Systeemvereisten . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2De stationhouder monteren . . . . . . . . . . . . . . . . . . . . . . . . . . . .3Het stuurprogr...
Page 65 - INLEIDING
Ne De houder voor externe High-Speed USB 2.0-stations (het Externestation) is een draagbaar compact opslagstation waarin een High-Speed interface van het type USB 2.0 (Universal Serial Bus 2.0) isingebouwd. Het Externe station biedt een snelle en makkelijke manierom uw computer van meer opslagruimte...
Page 66 - SYSTEEMVEREISTEN
2 SYSTEEMVEREISTEN Hardware Notebook- en desktop-computers met USB 1.0- of USB 2.0-poort Besturingssysteem Windows ® 98 SE, Me, 2000, of XP P74080-em-F5U209-man_9-02.qxd 9/19/02 3:06 PM Page 2
Page 67 - DE STATIONHOUDER MONTEREN; Verwijder de top van het Externe station.
Ne DE STATIONHOUDER MONTEREN 1. Verwijder de top van het Externe station. 2. Als u een vaste schijf van 3,5-inch installeert, dient uervoor te zorgen dat deze schijf als 'Master' is ingesteld(zie de informatie over jumperinstellingen die boven op devaste schijf wordt vermeld). Sluit vervolgens de 34...
Page 68 - bij uw externe High-Speed stationhouderkit
DE STATIONHOUDER MONTEREN Opmerking: bij uw externe High-Speed stationhouderkit worden vier schroeven met een fijne schroefdraad en vierschroeven met een grove schroefdraad meegeleverd. Zorgervoor dat u de schroeven gebruikt die bij de montagegaatjesvan uw station passen. Probeer in geen geval een s...
Page 70 - Belangrijke opmerking:
6 DE STATIONHOUDER MONTEREN 8. Plaats de montage-uitsteeksels aan de vrije kant van hetvoorpaneel in de tweede zijrail en haak de zijrail vast aan devoorkant van het Externe station. 9. Voltooi de montage door de rail vast te drukken in de zesrechthoekige montagegaatjes aan de zijkant van het Extern...
Page 71 - wanneer u het externe station aansluit op een
Ne DE STATIONHOUDER MONTEREN 10. Steek het vierkante verbindingsstuk van de USB-kabel in deUSB-poort aan de achterkant van het Externe station. 11. Sluit het rechthoekige verbindingstuk van de USB-kabel aanop een High-Speed USB 2.0-poort op de computer of opeen High-Speed USB 2.0-hub. U kunt de kabe...
Page 72 - HET STUURPROGRAMMA INSTALLEREN; Kies Voltooien en klik op Volgende.
8 HET STUURPROGRAMMA INSTALLEREN Windows 98 SE 1. Plaats de installatie-cd in het cd-rom-station. 2. Open de installatie-cd. 3. Voer het programma TPPINST.EXE uit om destuurprogramma's voor het externe USB 2.0-stationte installeren. 4. Er wordt een installatievenster weergegeven. Klik op Volgende. 5...
Page 75 - Formatteren onder Windows 98/Me; Sluit het Externe station aan.; Via het Configuratiescherm; Kies achtereenvolgens Start en Instellingen.
Ne EEN EXTERN USB 2.0-STATION FORMATTEREN Formatteren onder Windows 98/Me 1. Start de computer op en start het Windows-besturingssysteem. 2. Sluit het Externe station aan. Er zijn twee manieren waarop u een vaste schijf met USB 2.0-aansluiting kunt partitioneren en formatteren. Via het Configuraties...
Page 76 - als u deze methode gebruikt om de verwisselbare
12 EEN EXTERN USB 2.0-STATION FORMATTEREN 5. Selecteer Schijfstations. De nieuwe vast schijf wordt in de lijstmet vaste schijven weergegeven (in dit geval als Toshiba1924FVC). 6. Dubbelklik op het item dat uw vaste schijf aanduidt. KiesInstellingen. Het volgende scherm wordt weergegeven. 7. Zorg erv...
Page 78 - klik in Windows XP achtereenvolgens op Start,
14 EEN EXTERN USB 2.0-STATION FORMATTEREN BELANGRIJK Zorg ervoor dat u optie 5 selecteert en wijzig de huidige vasteschijf van 'station 1' in het schijfnummer dat aan het Externestation is toegewezen. Als de computer maar één internschijfstation heeft, wordt het nieuwe Externe station als Station2 g...
Page 80 - INFORMATIE; VERKLARING VAN CONFORMITEIT MET DE REGELS VAN
16 INFORMATIE FCC-verklaring VERKLARING VAN CONFORMITEIT MET DE REGELS VAN DE FCC VOOR ELEKTROMAGNETISCHE COMPATIBILITEIT Wij, Belkin Corporation, 501 West Walnut Street, Compton, CA 90220, verklarende exclusieve verantwoordelijkheid te dragen dat het product F5U209 waaropdeze verklaring betrekking ...
Page 83 - ÍNDICE
Es ÍNDICE Introducción . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1Requisitos del sistema . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2Montaje del alojamiento de la unidad . . . . . . . . . . . . . . . . . . . . .3Instalación del controlador ....
Page 85 - INTRODUCCIÓN
El Alojamiento de unidad externa USB 2.0 de alta velocidad (laUnidad externa) es una unidad de almacenamiento, compacta yportátil que incorpora la interfaz de alta velocidad USB 2.0 (Bus SerieUniversal 2.0). La Unidad externa proporciona una forma fácil y rápidade añadir más capacidad de almacenaje ...
Page 86 - REQUISITOS DEL SISTEMA
2 REQUISITOS DEL SISTEMA Hardware Ordenadores portátiles y de sobremesa con puerto USB 1.0 o USB 2.0 Sistema operativo Windows ® 98 SE, Me, 2000, o XP P74080-em-F5U209-man_9-02.qxd 9/19/02 3:06 PM Page 2
Page 87 - MONTAJE DEL ALOJAMIENTO DE LA UNIDAD; Desmonte la cubierta de la Unidad externa.
Es MONTAJE DEL ALOJAMIENTO DE LA UNIDAD 1. Desmonte la cubierta de la Unidad externa. 2. Si instala un disco duro de 31/2 pulgadas, compruebe quela unidad está configurada como "Master" (consulte lainformación sobre la colocación de los jumper, impresa enla parte superior de la propia unidad...
Page 88 - En el kit del Alojamiento de la unidad externa de alta
Nota: En el kit del Alojamiento de la unidad externa de alta velocidad se incluyen 4 tornillos de rosca fina y cuatro tornillosde rosca gruesa. Asegúrese de elegir los tornillos que coincidancon los orificios de montaje de su unidad. No intente forzar lostornillos de rosca grueso en los orificios de...
Page 90 - Si utiliza Windows 98 o 98 SE, NO conecte la
6 MONTAJE DEL ALOJAMIENTO DE LA UNIDAD 8. Introduzca las lengüetas de montaje del extremo libre delpanel frontal en la segunda guía lateral y enganche ésta en laparte delantera de la Unidad externa. 9. Finalice el montaje presionando la guía sobre los seis orificios rectangulares de montaje situados...
Page 91 - Cuando se conecta a un puerto USB 1.1 el ancho de
Es MONTAJE DEL ALOJAMIENTO DE LA UNIDAD 10. Conecte el conector cuadrado del cable USB en el PuertoUSB situado en la parte posterior de la Unidad externa. 11. Conecte el conector rectangular del cable USB en unpuerto USB 2.0 de alta velocidad del PC o en unconcentrador USB 2.0 de alta velocidad. Tam...
Page 92 - INSTALACIÓN DEL CONTROLADOR; Inserte el CD de instalación en la unidad de CD ROM.
8 INSTALACIÓN DEL CONTROLADOR Windows 98 SE 1. Inserte el CD de instalación en la unidad de CD ROM. 2. Abra el CD de instalación. 3. Ejecute la aplicación “TPPINST.EXE” para instalar loscontroladores de la Unidad externa USB 2.0. 4. Aparece un cuadro de diálogo de la aplicación deinstalación. Haga c...
Page 93 - Si la nueva unidad no aparece en Mi PC, quizás sea
INSTALACIÓN DEL CONTROLADOR Nota: Si la nueva unidad no aparece en Mi PC, quizás sea necesario realizar una partición y dar formato a la unidad.Consulte la sección "Formato del disco externo USB 2.0" parapreparar la unidad de disco duro USB 2.0. En la bandeja del sistema aparecerá un icono d...
Page 95 - FORMATO DEL DISCO EXTERNO USB 2.0; Dar formato en Windows 98/Me; Arranque el PC en el sistema operativo Windows.; Método del Panel de control; Elija “Panel de control”.
11 Es FORMATO DEL DISCO EXTERNO USB 2.0 Dar formato en Windows 98/Me 1. Arranque el PC en el sistema operativo Windows. 2. Conecte la Unidad externa. Existen dos métodos para realizar la partición y formato de launidad de disco duro USB 2.0. Método del Panel de control 1. Haga clic en "Inicio...
Page 96 - El disco duro extraíble ya está listo para su uso.
12 FORMATO DEL DISCO EXTERNO USB 2.0 5. Seleccione "Unidades de disco". El Nuevo disco duroaparecerá en la lista de discos duros (en este caso como“Toshiba 1924FCV”). 6. Haga doble clic en la entrada de la unidad de disco duro.Seleccione “Configuración”. Aparecerá la siguiente pantalla. 7. A...
Page 97 - Método DOS (Recomendado sólo para usuarios avanzados)
Es FORMATO DEL DISCO EXTERNO USB 2.0 Método DOS (Recomendado sólo para usuarios avanzados) 1. Haga clic en "Inicio" y haga clic en "Programas". Seleccione “MSDOS”. 2. En el símbolo del sistema del DOS, escriba "FDISK" y pulse Enter. Nota: Si la utilidad FDISK finaliza sin mos...
Page 98 - IMPORTANTE
14 FORMATO DEL DISCO EXTERNO USB 2.0 IMPORTANTE Asegúrese de que se selecciona la opción 5 y cambie el "Discofijo actual" de "Disco 1" al número de disco asignado a laUnidad externa. Si el PC está equipado únicamente con undisco interno, el nuevo Disco externo se identificará como...
Page 99 - Si visualiza el Panel de control en modo clásico, vaya
Es FORMATO DEL DISCO EXTERNO USB 2.0 control", haga clic en el icono "Rendimiento y mantenimiento",haga clic en el icono "Herramientas administrativas" y luegohaga clic en el icono "Administración de equipos". Nota: Si visualiza el Panel de control en modo clásico, vaya d...
Page 100 - INFORMACIÓN; Declaración de la FCC
16 INFORMACIÓN Declaración de la FCC DECLARACIÓN DE CONFORMIDAD CON LAS REGLAS DE LA FCC PARA COMPATIBILIDAD ELECTROMAGNÉTICA Belkin Corporation, de 501 West Walnut Street, Compton, CA 90220,declaramos bajo nuestra exclusiva responsabilidad que el producto: F5U209 , alque se refiere esta declaración...
Page 103 - INDICE
It INDICE Introduzione . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1Requisiti di sistema . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2Assemblaggio del telaio dell'unità . . . . . . . . . . . . . . . . . . . . . . . .3Installazione del drive...
Page 105 - INTRODUZIONE
It Il telaio dell'unità esterna Hi-Speed USB 2.0 (l'unità esterna) è un'unitàdi memoria di massa compatta portatile che incorpora l'interfaccia adalta velocità USB 2.0 (Universal Serial Bus 2.0). L'unità esternagarantisce un modo facile e veloce per aggiungere ulteriore capacitàdi memoria al compute...
Page 106 - REQUISITI DI SISTEMA; Computer portatili e da tavolo con porta USB 1.0 o USB 2.0; Sistema operativo
2 REQUISITI DI SISTEMA Hardware Computer portatili e da tavolo con porta USB 1.0 o USB 2.0 Sistema operativo Windows ® 98 SE, Me, 2000, o XP P74080-em-F5U209-man_9-02.qxd 9/19/02 3:06 PM Page 2
Page 107 - ASSEMBLAGGIO DEL TELAIO DELL'UNITÀ; Togliere il pannello superiore dell'unità esterna.
It ASSEMBLAGGIO DEL TELAIO DELL'UNITÀ 1. Togliere il pannello superiore dell'unità esterna. 2. Se si installa un'unità rigida da 31/2 pollici, verificare chel'unità sia impostata su "Master" (fare riferimento alleinformazioni di impostazione del ponticello stampatesull'unità del disco), quin...
Page 108 - Vi sono quattro viti a filettatura sottile e quattro a
Nota: Vi sono quattro viti a filettatura sottile e quattro a filettatura grossa incluse nel kit del telaio dell'unità esterna adalta velocità. Fare attenzione a scegliere le viti che siano adatteai fori di montaggio dell'unità. Non cercare di forzare le viti afilettatura grossa nei fori per viti a f...
Page 110 - se si utilizza il sistema operativo Windows 98
6 ASSEMBLAGGIO DEL TELAIO DELL'UNITÀ 8. Inserire le linguette di montaggio sull'estremità libera delpannello anteriore nella seconda guida laterale e agganciarela guida laterale sulla parte anteriore dell'unità esterna. 9. Completare l'assemblaggio premendo la guida dentro i seifori di montaggio ret...
Page 111 - Quando si esegue una connessione ad una porta USB
It ASSEMBLAGGIO DEL TELAIO DELL'UNITÀ 10. Inserire il connettore a forma quadrata del cavo USB nellaporta USB sul pannello posteriore dell'unità esterna. 11. Inserire il connettore a forma rettangolare del cavo USB inuna porta USB 2.0 High-Speed del computer o dell'hub Hi-Speed USB 2.0. È possibile ...
Page 112 - INSTALLAZIONE DEL DRIVER; Inserire il CD di installazione nell'unità CD-ROM
8 INSTALLAZIONE DEL DRIVER Windows 98 SE 1. Inserire il CD di installazione nell'unità CD-ROM 2. Aprire il CD di installazione. 3. Eseguire “TPPINST.EXE” per installare i driver per l'unitàesterna USB 2.0. 4. Appare una casella di dialogo dell'installer. Fare clic su"Avanti", 5. Scegliere ...
Page 113 - Se la nuova unità non appare in Risorse del computer,
It INSTALLAZIONE DEL DRIVER Nota: Se la nuova unità non appare in Risorse del computer, potrebbe essere necessario eseguire la partizione e laformattazione dell'unità. Fare riferimento al capitolo"Formattazione dell'unità esterna USB 2.0" per prepararel'unità del disco rigido USB 2.0. Sulla ...
Page 115 - FORMATTAZIONE DELL'UNITÀ; Formattazione in Windows 98/Me; Avviare il computer nel sistema operativo Windows.; Metodo del pannello di controllo; Apparirà la seguente finestra.
It FORMATTAZIONE DELL'UNITÀ ESTERNA USB 2.0 Formattazione in Windows 98/Me 1. Avviare il computer nel sistema operativo Windows. 2. Attaccare l'unità esterna. Ci sono a disposizione due metodi di partizione e formattazionedell'unità del disco rigido USB 2.0. Metodo del pannello di controllo 1. Fare ...
Page 116 - Usando questo metodo per la formattazione del disco
12 FORMATTAZIONE DELL'UNITÀ ESTERNA USB 2.0 5. Selezionare "Unità disco". Il nuovo disco rigido apparirànell'elenco dei dischi rigidi (in questo caso come “Toshiba1924FCV”). 6. Fare doppio clic sulla voce del disco rigido. Selezionare"Impostazioni". Apparirà la seguente finestra. 7. ...
Page 117 - Metodo DOS (raccomandato solo per utenti avanzati)
13 It FORMATTAZIONE DELL'UNITÀ ESTERNA USB 2.0 Metodo DOS (raccomandato solo per utenti avanzati) 1. Fare clic su "Start" e scegliere "Programmi". Selezionare "MSDOS". 2. Al messaggio DOS, digitare "FDISK" e premere "Invio". Nota: Se l'utility FDISK termina se...
Page 118 - In Windows XP, fare clic su “Start”, scegliere “Pannello di
14 FORMATTAZIONE DELL'UNITÀ ESTERNA USB 2.0 IMPORTANTE Selezionare l'opzione 5 e cambiare il "Disco fisso corrente" da"Disco 1" al numero di disco assegnato all'unità esterna. Se ilcomputer è dotato solo di un'unità disco interna, la nuova unitàesterna sarà identificata come "Dis...
Page 119 - Se si sta visualizzando il pannello di controllo nella
15 It FORMATTAZIONE DELL'UNITÀ ESTERNA USB 2.0 Nota: Se si sta visualizzando il pannello di controllo nella modalità classica, passare direttamente su "Strumentiamministrativi". 2. Fare clic su "Gestione disco". Tutte le unità disco connesseverranno visualizzate nell'angolo inferiore...
Page 120 - INFORMAZIONI; Dichiarazione FCC
16 INFORMAZIONI Dichiarazione FCC DICHIARAZIONE DI CONFORMITÀ CON LE REGOLAMENTAZIONI FCC PER LA COMPATIBILITÀ ELETTROMAGNETICA La Belkin Corporation, con sede in 501 West Walnut Street, Compton, CA 90220,dichiara sotto la sua responsabilità che il prodotto: F5U209 è conforme alla Parte 15 della reg...
Page 125 - INTRODUÇÃO
Po A caixa da unidade externa USB 2.0 de alta velocidade (a unidadeexterna) é uma unidade de armazenamento compacta portátil queintegra o interface de alta velocidade USB 2.0 (Universal Serial Bus2.0). A unidade externa fornece uma forma simples e rápida paraadicionar mais espaço de armazenamento ao...
Page 126 - REQUISITOS DO SISTEMA
2 REQUISITOS DO SISTEMA Hardware Computador de secretária ou computador portátil com portaUSB 1.0 ou USB 2.0 Sistema operativo Windows ® 98 SE, Me, 2000, ou XP P74080-em-F5U209-man_9-02.qxd 9/19/02 3:06 PM Page 2
Page 127 - MONTAGEM DA CAIXA DA UNIDADE; Remova a parte superior da unidade externa.
Po MONTAGEM DA CAIXA DA UNIDADE 1. Remova a parte superior da unidade externa. 2. Se instalar um disco rígido de 3,5 polegadas, certifique-sede que a unidade está definida para “Master” (consulte asinformações de definição dos jumpers impressas na partesuperior do disco rígido) e, em seguida, ligue ...
Page 128 - Existem quatro parafusos de rosca fina e quatro
Nota: Existem quatro parafusos de rosca fina e quatro parafusos de rosca normal no kit da caixa da unidade externade alta velocidade. Certifique-se de que os parafusoscorrespondem aos orifícios de montagem da unidade. Nãotente aparafusar à força um parafuso de rosca normal numorifício de montagem de...
Page 130 - Se utilizar o Windows 98 ou 98 SE, NÃO
6 MONTAGEM DA CAIXA DA UNIDADE 8. Insira as patilhas de montagem na extremidade livre dopainel frontal na segunda calha lateral e encaixe a calhalateral na parte frontal da unidade externa. 9. Pressione a calha contra os seis orifícios de montagemrectangulares existente na parte lateral da unidade e...
Page 131 - Quando ligado a uma porta USB 1.1 de velocidade total,
7 Po MONTAGEM DA CAIXA DA UNIDADE 10. Ligue o conector quadrado do cabo USB à porta USBexistente no painel posterior da unidade externa. 11. Ligue o conector rectangular do cabo USB a uma porta USB2.0 de alta velocidade no computador ou no hub 2.0 dealta velocidade. Pode também ligar o cabo a uma po...
Page 132 - INSTALAÇÃO DE CONTROLADORES; Insira o CD de instalação na unidade de CD-ROM.
8 INSTALAÇÃO DE CONTROLADORES Windows 98 SE 1. Insira o CD de instalação na unidade de CD-ROM. 2. Abra o CD de instalação. 3. Execute o “TPPINST.EXE” para instalar os controladores daunidade externa USB 2.0. 4. Aparece a caixa de diálogo do programa de instalação. Façaclique em “Seguinte”. 5. Selecc...
Page 133 - Se a nova unidade não aparecer em O Meu Computador,
9 Po Nota: Se a nova unidade não aparecer em O Meu Computador, pode necessitar de dividir e formatar a unidade. Consulte asecção “Formatar a unidade externa USB 2.0” para preparar odisco rígido USB 2.0. Um ícone verde “Desligar ou ejectar hardware” aparece notabuleiro do sistema. Windows Me/2000/XP ...
Page 135 - FORMATAÇÃO DA UNIDADE EXTERNA USB 2.0; Formatar no Windows 98/Me; Arranque o computador no sistema operativo Windows.; Método do Painel de controlo; Faça clique em “Iniciar” e seleccione “Definições”.
11 Po FORMATAÇÃO DA UNIDADE EXTERNA USB 2.0 Formatar no Windows 98/Me 1. Arranque o computador no sistema operativo Windows. 2. Ligue a unidade externa. Existem dois métodos para dividir e formatar o disco rígidoUSB 2.0. Método do Painel de controlo 1. Faça clique em “Iniciar” e seleccione “Definiçõ...
Page 136 - O disco rígido amovível já está pronto a utilizar.
12 FORMATAÇÃO DA UNIDADE EXTERNA USB 2.0 5. Seleccione “Unidades de disco”. O novo disco rígidoaparece na lista de discos rígidos (neste caso, “Toshiba1924FCV”). 6. Faça clique duas vezes na entrada do disco rígido.Seleccione “Definições”. Aparece o ecrã seguinte. 7. Certifique-se de que seleccionou...
Page 137 - Na linha de comandos DOS, digite “FDISK” e prima “Enter”.
13 Po FORMATAÇÃO DA UNIDADE EXTERNA USB 2.0 Método DOS (Recomendado apenas para os utilizadores avançados) 1. Faça clique em “Iniciar” e seleccione “Programas”.Seleccione “MSDOS”. 2. Na linha de comandos DOS, digite “FDISK” e prima “Enter”. Nota: Se o utilitário FDISK terminar sem exibir uma mensage...
Page 138 - No Windows XP, faça clique em “Iniciar”, seleccione
14 FORMATAÇÃO DA UNIDADE EXTERNA USB 2.0 IMPORTANTE Certifique-se de que seleccionou a opção 5 e altere o “CurrentFixed Disk (Disco fixo actual)” de “Disk 1 (Disco 1)” para onúmero do disco atribuído à unidade externa. Se o computadorestiver equipado apenas com uma unidade interna, a novaunidade ext...
Page 139 - Se estiver a ver o Painel de controlo no modo clássico,
15 Po FORMATAÇÃO DA UNIDADE EXTERNA USB 2.0 Nota: Se estiver a ver o Painel de controlo no modo clássico, avance directamente para as “Ferramentas administrativas”. 2. Faça clique em “Gestão de discos”. Todas as unidades dedisco ligadas aparece no canto inferior direito da janela“Gestão do computado...
Page 140 - INFORMAÇÕES
16 Declaração FCC DECLARAÇÃO DE CONFORMIDADE COM AS REGRAS DA FCC RELACIONADAS COM A COMPATIBILIDADE ELECTROMAGNÉTICA Nós, Belkin Corporation, sediada em 501 West Walnut Street, Compton CA90220, EUA, declaramos sob nossa responsabilidade que o produto: F5U209 o produto a que se refere a presente dec...