Axis dual ptz network camera - Manual

AXIS Q8721-E Installation Guide Page 7 EN GLISH Install the Hardware For information on the cameras’ connectors, LED behaviors etc., see the respective User Manuals. Install the Power Supply (sold separately) The mains supply shall be disconnected during installation. The power supply specified with...

Page 8 AXIS Q8721-E Installation Guide Install the Bracket (sold separately) 1. Prepare a wall, parapet or pole for installation of the selected bracket (sold separately). See www.axis.com for information on available mounting accessories. 2. Route the network, power and, if applicable, illuminator ...

AXIS Q8721-E Installation Guide Page 9 EN GLISH 4. Assemble the screws, washers and screw seals.5. Put the seal in its position. 1 5 3 4 1 2 2 3 4 6 1 Screw seal (4x) 4 Screw (4x) 2 Seal 5 Column bracket 3 Washer (4x) 6 Wall bracket

Page 10 AXIS Q8721-E Installation Guide Attach the Base to the Bracket 1. Remove the desiccant bag, which is placed in the base.2. Make sure the seal is in position.3. Route the network, power and, if applicable, illuminator cables through their respective cable glands in the base. The cable glands ...

AXIS Q8721-E Installation Guide Page 11 EN GLISH 5. Attach the base to the bracket and tighten the screws (torque 4 Nm). Apply Loctite 243  threadlocker on the screws. The base can be attached to the bracket in four different positions. Use the alignment indicators on the dif-ferent units to find a...

Page 12 AXIS Q8721-E Installation Guide 6. If applicable, connect the illuminator cable to the connector (ALARMS and 1) on the base.7. Using a RJ45 crimp tool, strip and crimp the network cable according to the manufacturer’s instructions.8. Connect the network cable to the network connector on the ...

AXIS Q8721-E Installation Guide Page 13 EN GLISH Attach the Dual PTZ Network Camera to the Base 1. Make sure the seal is in position.2. Remove the sunshield, which is placed on but not attached to, from the top cover.3. Attach the Pan/Tilt control unit, motor and camera assembly to the base and tigh...

Page 14 AXIS Q8721-E Installation Guide Install the Counterweights 1. Unscrew the bottom cover screws and remove the top cover, see illustration on page 15.2. Attach the counterweights to the bottom cover using the supplied screws and washers (torque 4 Nm). Apply Loctite 243  threadlocker on the sc...

Page 16 AXIS Q8721-E Installation Guide 8. Switch on the mains supply. The pan/tilt control unit will start turning and the cameras will turn on approximately 30 seconds later. In cold temperatures, there might be a delay due to the de-icing process, see Day/Night Sensor, on page 17. Risk of pinchin...

AXIS Q8721-E Installation Guide Page 17 EN GLISH Configuration For information about how to assign an IP address and gain access to the product, see Access the Video Stream, on page 18 and the Installation and Management Software CD. PTZ The PTZ functionality is controlled through the network camera...

Page 18 AXIS Q8721-E Installation Guide Access the Video Stream Use the tools provided on the Installation and Management Software CD to assign an IP address, set the password and access the video stream. This information is also available from the support pages on www.axis.com/techsup Focus Adjustm...

AXIS Q8721-E Installation Guide Page 19 EN GLISH Resetting to the Factory Default Settings This will reset all parameters, including the IP address, to the Factory Default settings: 1. Disconnect power from the camera.2. Press and hold the control button and reconnect power.3. Keep the control butto...

Page 20 AXIS Q8721-E Installation Guide Technical Specifications For technical specifications of the network cameras, see the respective User Manuals. Further Information Visit www.axis.com/techsup to check if there is updated firmware available for your network product. To see the currently install...