Aube TI035 - Manual

TI035

400-035-001-C 13/3/07 1/2

TI035

Installation and User Guide

Programmable Wall Switch

The TI035 programmable wall switch has been designed to control lightings
and motors:

NOTE

: This switch cannot be used if there are not at least 2 white wires joined

by a connector inside the electrical box.

n

Cut power at the circuit breaker to avoid electric shock.

o

Remove the existing switch.

p

Install the new switch as shown in the diagram below.

q

Apply power at the circuit breaker.

n

Pry the switch door open from the bottom
using a small screwdriver.

o

Ensure the

ON/OFF

selector is set to ON.

p

Reset the switch using a paper clip.

0:00

will flash.

If the display is blank:
•

Ensure the

ON/OFF

selector is properly

engaged in the

ON

position. Push it to the

right using a small screwdriver.

The programmable switch has 2 operating modes: manual (

MAN

) and

automatic (

AUTO

). To switch mode, press the switch door for 3 seconds.

Manual Mode

The programmable switch operates as a regular switch.
Briefly press the switch door to turn the lights On or Off.
The mode (

MAN

)

and state (

ON

or

OFF

) are displayed.

Automatic Mode

The programmable switch follows the programmed
schedule. The mode (

AUTO

), state (

ON

or

OFF

) and

current program number are displayed.
To temporarily override the programmed schedule, briefly
press the switch door. The new state (

ON

or

OFF

) will flash

to show that the state is temporary. The override remains in effect until you
press the switch door again or until the beginning of the next program.

NOTE

: The switch displays the time in 24-hour format by default or following a

reset.

n

To switch between 12-hour format and 24-hour format, proceed as
follows:
a) Press one of the control buttons to ensure the

MAN

or

AUTO

indica-

tor is displayed.

b) Press the

MIN

and

HOUR

buttons simultaneously and brieftly (

0:00

display = 24-hour;

12:00

display = 12-hour ).

o

Set the time using the

HOUR

and

MIN

buttons. For the 12-hour time

format, if you are setting an afternoon time, ensure

PM

appears on the

screen.

p

Press one of the control buttons or close the switch door to return to
normal operation.

This procedure sets the switch for daylight savings time or for standard time.

n

Press the

CODE

button four times.

o

Press the

MIN

button to switch between

nor

and

Ad

.

p

Press one of the control buttons or close the switch door to return to nor-
mal operation.

NOTE

: By default, once you have programmed the sunset/sunrise

parameters, the timer will follow the sunrise/sunset program when placed in
Automatic mode. To set your own schedule, see section 8.

7.1

Determining the sunset/sunrise parameters

Fill out the following table:

1)

LATITUDE & LONGITUDE

: Enter the coordinates of your city or the

nearest city using the supplied table. If none of the cities in the table is appli-
cable, this information is usually available on the internet.

NOTE

: Add a minus sign when entering a south latitude coordinate or a west

longitude coordinate.

n

Applications

1.

Load type

Maximum load

Examples

Resistive load

2400 W
(20 A @ 120 V)

•

incandescent lights

•

halogen lights

•

block heater

Inductive load

2400 W
(20 A @ 120 V)

•

fluorescent lights

•

compact fluorescent lights (CFL)

•

sodium lamps

•

electronic ballasts

Motor

1 hp

•

pool filter pumps

•

fans

o

Installation

2.

p

Power-on

3.

q

Operating Modes

4.

120 VAC

white (neutral)

black (line)

white

black

white

black

blue

Control (4)

Reset

On/Off
selector

r

Setting the Clock

5.

s

Daylight Savings Time

6.

nor

Standard time / Normal time / Winter time

Ad

Daylight savings time / Advanced time / Summer time

t

Sunset/Sunrise Program

7.

Latitude

Longitude

Day #

nor/Ad

Lc