Aube TH147 - Manual
Aube TH147 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Connecting the Thermostat; Note; Remote Control Input; Connecting to a Home Automation System; Setting JP2 Jumper; JP2 jumper
- Page 3 – Fan Operating Mode; Viewing and Setting the Ambient Temperature; Warning
- Page 4 – Configuration Menu; Technical Specifications
TH147 and TH148LE
400-147-010-C 27/11/06 1/4
The TH147 and TH148LE thermostats can be used to control:
• a gas, fuel oil or electric furnace - 2 or 3 wires
• a central air conditioner - 2 or 3 wires
• a hot water system with or without pump - 2 wires
• a millivolt system - 2 wires
• a central heating and cooling system - 4 or 5 wires
Attention
: These thermostats are not compatible with heat pumps
or multi-stage systems.
Note
: The installation must be performed by an electrician or a qual-
ified installer.
2.1 Removing the Old Thermostat
IN ORDER TO AVOID ANY RISK OF ELECTRIC SHOCK, CUT
POWER TO THE HEATING/COOLING SYSTEM.
n
Remove the old thermostat to access the wires.
Attention
: If the old thermostat was mounted onto an electrical box,
it might have been powered by 120/240 volts. In this case, the
TH147 or TH148LE thermostat cannot be used.
o
Identify and label each wire (with the corresponding letter on
the wire terminal) and remove it from its terminal.
p
If necessary, strip the end of each wire
(maximum of 6 mm).
q
Wrap the wires around a pencil to prevent
them from falling into the wall.
r
If the hole in the wall is too big, insulate it
using a non-flammable material in order
to avoid air draughts behind the thermostat.
2.2 Installing the New Baseplate
For a new installation, choose a location approximately 1.5 m
(5 feet) above the floor and on an inside wall. Avoid draughty
areas (top of staircase, air outlet, etc.), dead air spots (behind
doors), direct sunlight or areas near concealed pipes or chim-
neys.
n
Remove the thermostat faceplate.
o
Loosen the locking screw in order to separate the thermostat
from its baseplate (the screw cannot be completely removed).
p
Gently tilt the thermostat upwards.
q
Mark and bore the appropriate mounting holes (or use the
existing holes). Insert the plastic anchors.
r
Pass the wires through the opening of the baseplate and fix the
baseplate to the wall using the screws provided.
1. Introduction
Functions
T
H
147
T
H
148L
E
Heating/cooling control
X
X
Fan control
X
X
Programmable cycle lengths
X
X
Temperature display in °C or °F
X
X
Backlit display
X
X
Battery replacement indicator
X
X
Unoccupied mode activated remotely (requires Aube’s CT240)
X
Interchangeable faceplates (titanium, charcoal & taupe)
X
TH147 & TH148LE
Electronic Ther mostats
Installation
and User Guide
Display
Adjustment
buttons
System operating
mode selector
Fan operating
mode selector
Backlight
button
2. Installation
400-147-010-C (TH147_TH148 NP Aube) ENG.fm Page 1 Monday, November 27, 2006 10:41 AM
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
TH147 and TH148LE 400-147-010-C 27/11/06 2/4 2.3 Connecting the Thermostat Refer to the following table for matching the wire labels with thethermostat terminals. Note : Do not connect wires identified as C, X or B. Wrap the bare end of these wires with electrical tape. n Loosen the screws of the te...
TH147 and TH148LE 400-147-010-C 27/11/06 3/4 2.6 Installing the Batteries n Gently pull out the battery cover. o Install the batteries as shown. Observe the polarity. p Reinstall the battery cover. You will hear a clicking sound. When batteries are installed for the first time, the thermostat per-fo...
TH147 and TH148LE 400-147-010-C 27/11/06 4/4 n To access the configuration menu, press the backlight button for 3 seconds. o To go to the next parameter (menu item), briefly press the backlight button. p To modify a parameter, press . q Repeat steps 2 and 3 if necessary. r Press the backlight button...
