Arkon TT135 - Manual
Arkon TT135 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
for Tomtom One
TT135 | 7” Freedom Mount Windshield / Dash / Console Mount for Tomtom GPS
Consumer Hotline:
(USA) (800) 841-0884
(INT'L) (626) 254-9005
Mon-Fri. 9am-5pm, PST
www.arkon.com
Arcadia, CA 91006 USA
Made in Taiwan
© Copyright 2007 Arkon Resources, Inc.
The Mobile Mounting Specialists
TM
Safety Precautions
Do not install Arkon products over an air bag cover or within the air
bag deployment zone. Arkon Resources, Inc. assumes no responsi-
bility of liability for injury or death as a result of car crashes and/or
air bag deployment.
Arkon Resources, Inc. is not responsible for any damages caused to
your car, your device, or yourself due to the installation or use of the
pedestal mount.
Step 1.
Step 2.
Attach the adapter plate by sliding it up into the slot on the back of the
Tomtom GO 520, 720, 920, or 920T device as shown above.
Follow step 2 from
Pedestal Adjustment and Device Adapter Plate
Installation
above.
Instructions for APTTGO520 Adapter Plate
TM
Step 1.
Windshield Installation
Push the pedestal suction cup (A) firmly to the windshield.
Flip the lever (B) down to secure the suction cup.
(A)
(B)
for Tomtom One XL
and Tomtom One XL-S
for Tomtom GO 520,
720, 920, and 920T
APT TO
APT TOXL
APT TGO520
AP036
Compatible with:
Step 1.
Step 2.
Locate a safe flat surface
on the dash or console to
mount the pedestal. Clean
the dash with the alcohol
pad provided. Let the dash
surface dry before applying
the adhesive disc (C).
Push the pedestal suction
cup (A) firmly to the disc (C).
Flip the lever (B) down to
secure the suction cup.
Dash Installation
(A)
(C)
(B)
Step 1.
Step 2.
Adjust the arm angle and the pedestal head by tightening the adjustment
knobs.
(D)
Attach the adapter plate to the back of the device. Attach the device and
plate to the pedestal by inserting the dual T-Tabs of the pedestal
(E)
into the
dual T-slots of the adapter plate.
(F)
Tomtom One, One XL, and One XL-S Mount Installation
Pedestal Adjustment and Device Adapter Plate Installation
(F)
(E)
(D)
(D)
Step 1. Remove the tightening nut and screw to remove the dual-T plate head.
Insert the mounting arm into the Tomtom GO 300, 500, or 700 adapter
(not included). Attach the device to the adapter plate.
Instructions for GO 300, 500, and 700 adapter plate
CM027-2
for GO 300, 500, & 700
without dual-T plate
t5PNUPN0OF
st
, 2
nd
, & 3
rd
Editions
t5PNUPN0OF 6,WFSTJPO
t̓5PNUPN0OF9-
st
, 2
nd
, & 3
rd
Editions
t5PNUPN0OF9-4
st
, 2
nd
, & 3
rd
Editions
t5PNUPN(05
t5PNUPN(0
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
