Arkon tt124 - Manual

TT124 | Adhesive Dash / Console Mount for Tomtom GPS Devices

CM024-2

Consumer Hotline:
(USA) (800) 841-0884
(INT'L) (626) 254-9005
Mon-Fri. 9am-5pm, PST

www.arkon.com

Arcadia, CA 91006 USA

Made in Taiwan

© Copyright 2007 Arkon Resources, Inc.

The Mobile Mounting Specialists

TM

Safety Precautions

Do not install Arkon products over an air bag cover or within the air
bag deployment zone. Arkon Resources, Inc. assumes no responsi-
bility of liability for injury or death as a result of car crashes and/or
air bag deployment.

Arkon Resources, Inc. is not responsible for any damages caused to
your car, your device, or yourself due to the installation or use of the
pedestal mount.

Step 1.

Step 2.

Step 3.

Step 1.

Choose the best location on vehicle to place the mount.

Do not place mount in or near an air bag deployment zone or
where it will obstruct view of the road.

Clean off dash surface with alcohol cleaning pad and let dry.

(A)

Do not attempt application of the dash mount if the temperature
is below 68o F (20oC).

Remove paper liner from adhesive on base

(B)

and affix

adhesive to the dash. Let stand (at room temperature) for
24 hours before using.

For a more permanent mount, connect the pedestal to the dash
or console. This will require drilling into your vehicle’s interior
surface with self-tapping screws (not included).

Pedestal Mounting

Compatible with:

t5PNUPN0OF

st

, 2

nd

, & 3

rd

Editions

t5PNUPN0OF 6,WFSTJPO

t̓5PNUPN0OF9-

st

, 2

nd

, & 3

rd

Editions

t5PNUPN0OF9-4

st

, 2

nd

, & 3

rd

Editions

t5PNUPN(05

t5PNUPN(0

Pedestal Mounting with screws (Optional)

Step 1.

Step 2.

Adjust the arm angle and the pedestal head by tightening the
adjustment knobs.

(D)

"UUBDIUIFBEBQUFSQMBUFUPUIFCBDLPGUIF5PNUPN0OF0OF9-
PS0OF9-4EFWJDF"UUBDIUIFEFWJDFBOEQMBUFUPUIFQFEFTUBM

by inserting the dual T-Tabs of the pedestal

(E)

into the dual

T-slots of the adapter plate.

(F)

Tomtom One, One XL, and One XL-S Mount Installation
Pedestal Adjustment and Cradle Attachment

Step 1.

Step 2.

Attach the adapter plate by sliding it up into the slot on the back

PGUIF5PNUPN(0BOE5EFWJDFBTTIPXOBCPWF

Follow Step 2 above.

Instructions for APTTGO520 Adapter Plate

Step 1. Remove the tightening nut and screw to remove the dual-T plate

IFBE*OTFSUUIFNPVOUJOHBSNJOUPUIF5PNUPN(0PS
BEBQUFS OPUJODMVEFE"UUBDIUIFEFWJDFUPUIFBEBQUFSQMBUF

5PNUPN(0PS
BEBQUFS OPUJODMVEFE

Instructions for GO 300, 500, and 700 adapter plate

(B)

(A)

Safety Precautions

Drilling onto the dash, floor or console will permanently damage the vehicle.

6TFDBVUJPOBOEDPOTVMUBNPCJMFJOTUBMMQSPGFTTJPOBMUPBWPJEESJMMJOHJOUPUIF

gas tank, electrical system or other highly sensitive vehicle components.

Arkon Resources, Inc. is not responsible for any damages caused to your car
or yourself due to the install of the pedestal mount.

(F)

(E)

(D)

Removal of Dash

M

ount

To remove the dash mount completely, use a cotton swab dipped in isopropyl
alcohol. Simply peel up a corner of the dash mount adhesive and swab under
the pad while gently pulling until the adhesive begins to release. Remove slowly.
No damage will occur from the adhesive if it has been properly installed and
removed per these instructions. You may see a slight discoloration between
this area and other parts of your dash due to fading caused by the sun.

GPS5PNUPN0OF

GPS(0

without dual-T plate

GPS5PNUPN0OF9-

BOE5PNUPN0OF9-4

GPS5PNUPN(0

BOE5

"1550

"15509-

"155(0