Apple Computer Monitor - Manual
Apple Computer Monitor – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Use of the remote control
- Page 3 – pπ; Picture format
- Page 4 – . Wall mounting bracket included; Tips
Unpacking and wall mounting instructions
For the unpacking instructions follow the illustrated steps
1
to
5
printed
on the packaging (outside and inside).
For the wall mounting instructions follow the illustrated steps
6
to
8
printed on the first pages of this instruction booklet.
Make sure that the wall mount is being fixed securely enough so that it meets
safety standards. The weight of the monitor (excl. packaging) is about 43 kg.
Connect your computer
&
Connect one end of the VGA cable
1
supplied to the video card of the
computer and the other end to the
VGA IN
connector at the rear side of the
monitor. Fix the connectors firmly with the screws on the plug.
é
In case of a Multimedia computer, connect the audio cable
2
to the audio
outputs of your Multimedia computer and to the
AUDIO IN R
(right) and
L
(left) inputs of the monitor.
“
Connect one end of another VGA cable
3
to the
VGA OUT
connector at
the rear side of the monitor and the other end to the
VGA IN
connector of a
second VGA monitor.
Daisy chaining
The Active Loop Through facility makes it possible to make a daisy chain with
a second VGA monitor.
‘
In case of a Multimedia computer, also connect the audio cables
4
to the
AUDIO L
and
R
outputs of the monitor and to the
AUDIO IN L
and
R
inputs
of the second VGA monitor.
Note: only use the VGA cables supplied or use cables that are specially delivered
with the monitor.
Connect your Apple Macintosh* computer
Attention: Macintosh computers with separate H and V synchronisation signals
can be used together with the supplied adaptor. Macintosh computers with
Composite Sync and Sync on Green signals may need a special (not
supplied) adaptor or cable. Contact your dealer.
Connect the supplied switchable adaptor for Apple video connectors to one
end of a VGA cable.
Put the DIP switches on the adaptor in the following positions :
1
2
3
4
off
off
on
on
Connect the end of the VGA cable with the adaptor to the video card of the
computer and the other end to the
VGA IN
connector on the back of the
monitor.
Screw the connectors down firmly.
* Apple Macintosh is a registered trademark of Apple Computer, Inc.
1
15-pin D sub
(2-row)
15-pin mini D sub
(3-row)
a
MAINS INLET
VGA IN
AUDIO IN
L
R
VGA OUT
5
1
3
2
4
2
AUDIO OUT
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 VGA 640x480 31.468 kHz 60 Hz VGA 640x400 31.468 kHz 70 Hz VGA 640x350 31.468 kHz 70 Hz MAC II 640x480 35.000 kHz 67 Hz SVGA 800x600 35.156 kHz 56 Hz XGA 1024x768 45.000 kHz 56 Hz When a VGA computer is connected, the selection is made automatically. A message is displayed when the monitor does not...
3 Use of the remote control VGA OK FRONT o AV1 p MENU π AV2 œ AV3 ¬ AV4 SMART CONTROLS PICTURE SOUND - CH/P + - V + B VGA no function FRONT no function AV1 , AV2 , AV3, AV4 no function - CH/P + no function V press - or + to adjust the volume B no function OK to activate your choice MENU to switch th...
4 Ambient temperature Do not hang up the monitor above acentral heating or other heating sources. Active Loop Through The Active Loop Through facility makes itpossible to make a daisy chain for VGA.Maximum 2 sets. Care of the screen Clean the anti-reflex coated flat glassscreen with a slightly damp ...
