APC HT1000 - Manual

Data Port

BR24BP Battery Pack

User’s Manual

Back-UPS

®

HT1000

1

CONTENTS

2

3

CONNECT BATTERY CARTRIDGE

OPERATING ENVIRONMENT

3

4

CONNECT EQUIPMENT AND POWER

5

Building

Wiring Fault

Building Wiring

Fault Indicator

6a

Phone

Computer

Modem Port

CONNECT PHONE,

6b

CONNECT 10/100 Base-T

Network Jack

Computer

Network Port

8

To Computer USB

Port

CONNECT INTERFACE

Computer

There are four status indicators (lights) on the front

panel of the Back-UPS (On Line, On Battery,

Overload, and Replace Battery).

On Line (green)

- is lit whenever utility power is

powering the Battery Backup outlets.

On Battery (yellow)

- is lit whenever the battery of

the Back-UPS is powering equipment connected to

the Battery Backup Outlets.

Four Beeps Every 30 Seconds

- this alarm is

sounded whenever the Back-UPS is running

On Battery. Consider saving work-in-

progress.

Overload (red)

- is lit whenever power demand has

exceeded the capacity of the Back-UPS.

Continuous Tone

- this alarm is sounded

whenever the Battery Backup outlets are

overloaded.

Circuit Breaker

- the circuit breaker button

located on the rear panel of the Back-UPS will

stick out if an overload condition forces the

Back-UPS to disconnect itself from utility

power. If the button sticks out, disconnect non-

essential equipment. Reset the circuit breaker

by pushing the button inward.

Replace Battery (red)

- is lit whenever the

battery is near the end of its useful life, or if the

battery is not connected (see above). A battery

that is near the end of its useful life has

insufficient run-time and should be replaced.

Chirps for 1 Minute Every 5 Hours

-

this alarm is sounded whenever the

battery has failed the automatic

diagnostic test.

Note: Allow the Back-UPS to charge for a full eight

(8) hours prior to use.
Press the front panel Power ON/OFF switch and

observe that the following events occur after pressing

and releasing the switch:

• The green On Line indicator flashes.

• The yellow On Battery indicator lights while a

Self-Test is being performed.

• When Self-Test has successfully completed, only

the green On Line indicator will be lit.

• If the internal battery cartridge is not connected

(see Step 2 above), the green On Line indicator

and red Replace Battery indicators will light. The

Back-UPS will also emit a chirping sound.

Continuous Beeping

- this alarm is sounded

whenever a low battery condition is reached.

Battery run-time is very low. Promptly save

any work in progress and exit all open appli-

cations. Shutdown the operating system,

computer and the Back-UPS.

If the rear panel Building Wiring

Fault (red) indicator is lit, a potential

shock hazard exists due to one of the

following conditions:
• Open or high resistance ground
• Hot or neutral polarity reversed
• Overloaded neutral circuit

Improper building wiring should be

corrected by a qualified electrician.

Do not use the Back-UPS until the

condition that caused the fault is

corrected.
Note

: Improper building wiring will

not prevent the Back-UPS from

operating, but it will limit its

protection capability.

9

SWITCH ON THE BACK-UPS

On Line

On Battery

Overload

Replace Battery

w

w

w.apc.com

®

RJ-45

USB

STATUS INDICATORS AND ALARMS

For connection of APC’s optional

external 24-volt battery pack

(BR24BP) to the Back-UPS HT 1500.

CABLE

32 - 104

o

F (0 - 40

o

C)

Wall

Outlet

10/100 Base-T/VOIP

Modem/Phone/Fax

Jack

From Cable Provider

(Phone, Internet,

and/or CATV, or

DSS)

To Cable Modem,

VCR, DSS or TV

Cable Box

or VOIP

MODEM, FAX

CABLE IN

CABLE OUT

7

OR

✔

✔

✔

✔

✔

®

RJ-45

USB

RJ-11

RJ-11

✔

✔

✔

RJ-45

RJ-45

Coaxial Cable

User’s Manual

Software CD-ROM

Pedestal

Back-UPS HT

Plasma/

DVR or

CD / DVD Drive

Media PC

High Definition TV

Wall

Outlet

10/100 Base-T/VOIP

Modem/Phone/Fax

10

INSTALL SOFTWARE ON
COMPUTER

If Autoplay is enabled on your computer, the

software on the CD-ROM will automatically start

the installation program.

If Autoplay is not enabled on the computer, proceed

as follows:

1. On the computer desktop of the display, double-

click on My Computer.

2. Double-click on the CD-ROM drive icon and

follow the on-screen instructions.

Follow the

on-screen

instructions.

11

FINAL

ORIENTATION

✘

✔

✔

CONNECT COAXIAL CABLES
(PHONE, INTERNET, and/or
CATV or DSS)

CHECK BUILDING
WIRING FAULT
INDICATOR

To AC Utility

Power

Input: 120V~

12A, 60Hz

Circuit Breaker

Push to Reset

SURGEONLY

BATTERY BACKUP

Input: 120V~

12A, 60Hz

Circuit Breaker

Push to Reset

HT 1500 Rear Panel

HT 1000 Rear Panel

Note:

All outlets on the HT1500 provide

battery backup and surge protection.

and HT 1500