AMX RDM-2INC - Manual
AMX RDM-2INC – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Installation Sheet
RDM-2INC Dual Incandescent Dimmer Module
2400 W (x2)
The RDM-2INC Dual Incandescent Dimming Module 2400 W (x2) incan-
descent dimmer is designed for use with the RDA series of enclosures, in
an AMX Lighting™ modular digital dimming system. It can dim incandes-
cent lights, cold-cathode, neon and two-wire dimmable ballasts. The mod-
ule's 120, 240, and 277 VAC ratings are CE, UL, and C-UL approved.
RDM-2INC UL and C-UL Ratings
•
120 VAC, 50/60 Hz, 2400 W
•
240/277 VAC, 50/60 Hz, 2400 W
Suggested Dimmed Loads
•
Incandescent
•
Low-voltage
•
Neon, cold-cathode
•
Two-wire, phase-controlled ballast
Specifications
•
Dimensions (HW): 10.0" x 2.75" (25.4 cm x 6.99 cm)
•
Phase dependant
•
Use wires rated at 75°C (167°F)
•
Torque terminals to 7 in-lbs. (0.8 N/M)
•
Max. wire size: 10 AWG (4 mm²)
•
Wire stripping length: 0.28" (7 mm)
•
Weight: 6.5 lbs. (2.948 kg)
•
BTU/hr: 600
•
Control current: 45 mA @ 12 VDC per dimmer, 90 mA total
Caution: Pre-Installation Notes
•
All Class 1 wiring must be connected to proper terminals.
•
All control wiring must be connected to proper temrnials.
•
Disconnect power while installing or connecting the unit.
•
Keep top and bottom air vents clear at all times.
•
Test loads for shorts before connecting.
•
Use low voltage wires with a 300 volt rating or greater.
•
Use field installed copper conductors.
•
Run all low-voltage and control wires away from heat producing parts
of the dimmer.
•
Each dimming circuit must have a separate neutral connection.
•
All electrical ratings are for continuous duty.
•
AC lighting loads only.
•
For indoor use only.
•
This module may require extra power from the AXlink connection or an
external power supply connected to the control card.
Connecting the RDM-2INC to the AMX Lighting Master
Lighting Application Drawing
FIG. 1 RDM-2INC
Low-voltage
control wiring:
4-pin connectors
to AMX Lighting
master controller
350 µS choke
Dual 20 A power device
Line out
Line in (hot)
High-voltage
connections
Mounting
points
FIG. 2 RDM-2INC connections
FIG. 3 RDM-2INC wiring application
Pin 4 (GND)
Pin 3 (RLY)
Pin 2 (DIM)
Pin 1 (+12 V)
RDM-2INC four-pin module connector
4-pin plug from a RDM series module
Note: The 4-pin plugs from the module
connector to the 4-pin connector on the
master (black plug cover facing up).
2 (-)
1 (+)
Light A Light B
(B) Load
(A) Load
(B) Line in (HOT)
(A) Line in (HOT)
(A) Neutral
(B) Neutral
Neutral
Load
Load
Neutral
Neon lights
(cold-cathode, on/off)
Two-wire dimmable
ballast
Circuit breaker
panel
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
