AMX R-3 - Manual

Overview 2 Mio Modero R-3 Remote Touch And Tilt Sensor The Mio R-3 wakes up upon touching either the chrome side rails or pressing a button. When the remote times out while holding it, you can reawaken the device by tilting it. Errant jostling, such as a bumped table, will not wake the device unless...

Overview 3 Mio Modero R-3 Remote FCC Compliance This radio module was tested and certified as a stand-alone device according to FCC Rules CFR 47, Part 15, Subpart C. If this device is installed in a manner such that the radio module FCC ID. label is not visible on the outside of the end product, a l...

Mio Modero R-3 Setup 5 Mio Modero R-3 Remote Mio Modero R-3 Setup Inserting or Replacing the Lithium-ion Battery for the Mio R-3 The Mio Modero R-3 comes with a rechargeable Lithium-Ion battery that needs to be installed before use. To install your Lithium-Ion battery into the device: 1. Flip and tu...

Mio Modero R-3 Setup 6 Mio Modero R-3 Remote Installing Custom Buttons 1. Flip and turn the Mio R-3 device so that the buttons are facing away from you and the device is upside down. 2. Holding the Mio R-3 in both hands, place your thumbs on the battery door and push up to slide the battery door fre...

Setup Mode 7 Mio Modero R-3 Remote Setup Mode The Setup mode allows you to set the following device features on the Mio R-3: Transmit Mode Timeout Adjustment Download Mode Debug Mode Firmware Version Device ID LED Awake Brightness LED Sleep Brightness ZigBee ID PAN, Channel, and System Connection Si...

Setup Mode 8 Mio Modero R-3 Remote Download Mode In order to download new firmware or a new configuration or font file to the Mio R-3 remote using the remote's program port (see Using the Programming Jack on The Mio R-3 section on page 11 for details), the remote must first be placed into Download m...

Setup Mode 9 Mio Modero R-3 Remote LED Sleep Mode Brightness The red LEDs that backlight the Power button when the remote is awake are also used to indicate charging status. These LEDs will slowly blink on and off if the remote is place in the charging cradle and the Lithium-Ion battery pack is bein...

Programming The Mio R-3 11 Mio Modero R-3 Remote Programming The Mio R-3 Most functionality of the Mio R-3 is handled using the KeypadBuilder application. Go to www.amx.com for the KeypadBuilder Instruction Manual . The Mio R-3 recognizes a select number of Serial Commands. For a full list and descr...

Programming The Mio R-3 12 Mio Modero R-3 Remote Updating Mio R-3 Firmware Updating firmware in the Mio R-3 is also done through the programming jack. To update the main firmware for the Mio R-3: 1. Connect the Mio R-3 to your computer via the programming jack (FIG. 4). 2. Put the device into Downlo...

Programming The Mio R-3 13 Mio Modero R-3 Remote Channel Codes The following table gives the channel codes associated with each button on the Mio R-3. Thirty-six of the buttons change channel codes based on what button was last pressed. Nine of the buttons always emit the same channel code regardles...

Programming The Mio R-3 15 Mio Modero R-3 Remote Serial Commands The Mio R-3 remote supports a few commands that can be uploaded to the device using a terminal program such as HyperTerminal. These commands are not needed for normal usage or programming of the remote. Serial Commands @BRT Set Brightn...

Mio Remote Charging Base 27 Mio Modero R-3 Remote Mio Remote Charging Base The Mio remotes are complemented with a Mio-RCC charging base ( FG147-02) . Specifications FIG. 6 Mio-RCC Charging Base FIG. 7 Mio Remote Charging Base (Top and Bottom view) Rubber feet Angle barrel power connector Charging c...

Mio Remote Charging Base 28 Mio Modero R-3 Remote The specifications for the Mio remote charging base and kit are as follows: Charging The Mio Remote with Charging Base The Mio remotes receive power for charging from a charging base. 1. Connect the terminal end of the power supply to the bottom exte...