Page 2 - AMX Limited Warranty and Disclaimer
AMX Limited Warranty and Disclaimer This Limited Warranty and Disclaimer extends only to products purchased directly from AMX or an AMX Authorized Partner which include AMX Dealers, Distributors, VIP’s or other AMX authorized entity. AMX warrants its products to be free of defects in material and wo...
Page 3 - Table of Contents
Table of Contents i MIO R-1 AUDIO Table of Contents Overview ............................................................................................................ 1 Specifications ............................................................................................................ 2 To...
Page 5 - Overview
Overview 1 MIO R-1 AUDIO Overview The MIO R-1 AUDIO ( FG147-04 ) remote provides custom control features, contained in an elegant handheld device, designed specifically for use with Matrix Distributed Audio Systems using Metreau DAS-MET-6SRC and/or DAS-MET-NUM keypads. The MIO R-1 AUDIO (FIG. 1) con...
Page 6 - Specifications; Touch And Tilt Sensor
Overview 2 MIO R-1 AUDIO Specifications The MIO R-1 AUDIO device specifications are as follows: Touch And Tilt Sensor The MIO R-1 AUDIO wakes up upon touching either the chrome side rails or pressing a button. When holding the remote and it times out, you can reawaken the device by tilting it. Erran...
Page 8 - Battery Low Indicator
MIO R-1 AUDIO Setup 4 MIO R-1 AUDIO Battery Low Indicator When the battery charge level is too low to sustain continuous operation, the LCD flashes, "Battery Low" and the device shuts down.
Page 9 - Programming The MIO R-1 AUDIO; Using Connector Ports on The MIO R-1 AUDIO
Programming The MIO R-1 AUDIO 5 MIO R-1 AUDIO Programming The MIO R-1 AUDIO Most functionality of the MIO R-1 AUDIO is handled using the application KeypadBuilder . Go to www.amx.com for the KeypadBuilder Instruction Manual . The MIO R-1 AUDIO recognizes a select number of Serial Commands. For a ful...
Page 11 - Configuration Mode; STOP
Programming The MIO R-1 AUDIO 7 MIO R-1 AUDIO Configuration Mode The configuration mode allows you to set the following device features: IR Transmit Mode (38 KHz or 455 KHz) Timeout Adjustment Download Mode Debug Mode Battery Type LED Awake Brightness Sleep Brightness To enter configuration Mode: 1....
Page 12 - Debug Mode; Setting The IR Frequency
Programming The MIO R-1 AUDIO 8 MIO R-1 AUDIO Debug Mode Pressing button "4" on the remote toggles development mode between ON and OFF. The display indicates the selected mode. In development mode, the display shows the IR code assigned to buttons when pressed. This mode is useful to the pro...
Page 13 - Updating MIO R-1 AUDIO Firmware; Query for Devices
Programming The MIO R-1 AUDIO 9 MIO R-1 AUDIO Updating MIO R-1 AUDIO Firmware Updating firmware in the MIO R-1 AUDIO is also done through the programming jack. To update the main firmware for the MIO R-1 AUDIO: 1. Connect the MIO R-1 AUDIO to your computer via the programming jack (FIG. 3). 2. Put t...
Page 14 - Persistent Serial Commands
Programming The MIO R-1 AUDIO 10 MIO R-1 AUDIO Persistent Serial Commands There are a select number of persistent commands the MIO R-1 AUDIO recognizes. Establish a HyperTerminal session with your device to use the following commands: Serial Commands @BRT Set Brightness level Syntax: "'BRIT-<...
Page 15 - MIO Remote Charging Base
MIO Remote Charging Base 11 MIO R-1 AUDIO MIO Remote Charging Base The MIO remotes are complemented either with a MIO-RCC charging base ( FG147-02) or the MIO-RCC rechargeable upgrade kit ( FG147-03K) . One charging base, a new back housing and a MIO-RBP rechargeable lithium ion battery ( FG147-10 )...
Page 17 - Charging The MIO Remote with Charging Base
MIO Remote Charging Base 13 MIO R-1 AUDIO 5. Remove the back housing. 6. Place the new housing on the device so that the rechargeable battery port connection is now accessible. See FIG. 8. 7. Replace the 6 screws. 8. Connect the terminal end of the Lithium-Ion battery to the port shown in FIG. 8. It...
Page 18 - Changing Battery Modes; Battery Type; EXIT
MIO Remote Charging Base 14 MIO R-1 AUDIO Changing Battery Modes Configuration Mode The Configuration mode allows you to set the battery type. To enter Configuration mode: 1. Press and hold the STOP button and the INPUT button simultaneously. The two buttons must be pressed within 0.1 seconds of eac...
Page 19 - Using the MIO R-1 AUDIO Remote; Tone Control & SRS Setting
Using the MIO R-1 AUDIO Remote 15 MIO R-1 AUDIO Using the MIO R-1 AUDIO Remote Tone Control & SRS Setting To access the Tone Control and SRS settings, press the TONE button (FIG. 1). This enables the Tone Control Mode with BASS as the first mode selected. There are 3 Tone Control Modes available...
Page 20 - Privacy Mode; Zone Control; To turn a single Zone ON
Using the MIO R-1 AUDIO Remote 16 MIO R-1 AUDIO Privacy Mode When the privacy feature is engaged, the room/zone cannot be paged, apart from this, the room/zone will function normally. To engage Privacy mode, press the Privacy (PRIV) button. To disengage, press any Source or Navigation button. Zone C...
Page 21 - Source Control; Internal Tuner and Audio Server
Using the MIO R-1 AUDIO Remote 17 MIO R-1 AUDIO Source Control Internal Tuner and Audio Server CD and DVD Satellite and Other Pressing Source Buttons switches between sources and turns the Source On, but does not toggle between ON and OFF. FIG. 5 NAV array NAV Button Internal Tuner AUDIO SERVER NAV ...
Page 22 - Custom XM; Direct Numeric Access; Tuners; To select a specific Disc & Track; To select a specific track on the current disk; Satellite Radio/video
Using the MIO R-1 AUDIO Remote 18 MIO R-1 AUDIO Custom XM Direct Numeric Access Tuners Enter the station identification and press ENTER. Strings of 3 to 4 numbers are recognized. If a " • " (dot) is part of the string, then an FM station is assumed, otherwise an AM station is assumed. Exampl...
Page 23 - Presets; Creating a Preset; Recalling a Preset; Clearing All Presets
Using the MIO R-1 AUDIO Remote 19 MIO R-1 AUDIO Presets Creating a Preset 1. Select the source. 2. Direct Tune to the station of choice (enter station ID + ENTER). 3. Select the "PSET" button. 4. Key in the preset number (1 - 10). 5. Press & Hold ENTER. Example : Tune to 1050AM; press PS...
Page 24 - Zone Grouping; Adding a Zone To a Group
Using the MIO R-1 AUDIO Remote 20 MIO R-1 AUDIO Zone Grouping In this state, zones can be "grouped" together and controlled as a single zone. Press the "GRP" button to enter "Group Mode". Adding a Zone To a Group 1. Press the "GRP" button to enter "Group Mode"...
Page 25 - Favorites; Creating A favorite For A Specific Source; Clearing favorite for a Specific Source and Specific Zone
Using the MIO R-1 AUDIO Remote 21 MIO R-1 AUDIO Favorites One "favorite" can be programmed for each Source, in each Zone. If a "favorite" is set for a specific source in a specific zone, when that source is turned on (after System has been OFF), the favorite will begin playing in tha...
Page 26 - Alarm; Setting Alarm Time; Clearing Alarm For A Specific Zone
Using the MIO R-1 AUDIO Remote 22 MIO R-1 AUDIO Alarm When the alarm time is reached, the source selected will turn ON and the volume will ramp up to the set volume and begin playing. At this point the source will behave normally. Setting Alarm Time 1. Select Source & adjust the Volume to desire...
Page 27 - Keypad Lockout; Locking A Specific Keypad; Unlocking All Keypads
Using the MIO R-1 AUDIO Remote 23 MIO R-1 AUDIO Keypad Lockout Locking A Specific Keypad 1. Press "LOCK" button. 2. Enter the room/zone # to lock. 3. Press ENTER. Unlocking A Specific Keypad 1. Press "LOCK" button. 2. Enter the room/zone # to UNLOCK. 3. Press & Hold ENTER. Exampl...
