AMX Dms Keypad - Manual

Quick Start Guide

Mio Modero DMS

Keypad

Overview

The Mio Modero DMS device family provides a wide range of control capabilities in the
form of user specified buttons that are functional yet recherché.

Mio Modero DMS keypads are equipped with an LCD menu display with 8 pushbuttons
for navigation and menu selection.

Specifications

Dynamic Menu System

Using the KeypadBuilder application available for download from

www.amx.com

, the

Mio Modero DMS is programmed with a Dynamic Menu System (DMS) that is
navigated via the 8 pushbuttons and LCD display area. See the

KeypadBuilder

Instruction Manual

for more information on programming Mio Modero DMS devices.

Installation

Note:

To avoid any damage to the electronic component, installation must be

performed in an ESD safe environment.

The installation section addresses the mounting and wiring of the Mio Modero DMS.
After you have completed the installation you must consult

Necessary Device Setup

.

Rear Components

The rear components of the Mio Modero DMS (FIG. 2) are as follows:

Connections and Wiring

The Mio Modero DMS device is powered either via 12VDC or Power over Ethernet
(PoE). If both the 12 VDC and PoE power sources are connected, by default the device
draws power from the 12 VDC. If the 12 VDC source is disconnected, the PoE will
automatically supplies power after a device reboot.

Note:

Do not connect power to the Mio Modero DMS until the wiring is complete.

Preparing captive wires for the 2-pin 3.5 mm mini-Phoenix connector

You will need a wire stripper, and flat-blade screwdriver to prepare and connect the
captive wires.

1.

Strip 0.25 inch (6.35 mm) of wire insulation off all wires.

2.

Inser t each wire into the appropriate opening on the connector according to the
wiring diagrams and connector types described in this section.

3.

Turn the screws clockwise to secure the wires in the connector.

Note:

Do not over-torque the screws; doing so can bend the seating pins and damage

the connector.

Using the PSN NetLinx connector for power

The PWR and GND wires from the 12 VDC power supply must be connected to the
corresponding location on the 2-pin 3.5 mm mini-Phoenix connector (See the

KeypadBuilder Instruction Manual

for an illustration).

1.

Inser t the PWR and GND wires on the terminal end of a PSN 2-pin 3.5 mm mini-
Phoenix cable. Match the wiring locations of the +/- on both the power supply
and the terminal connector.

2.

Tighten the clamp to secure the two wires.

3.

Verify the connection of the 2-pin 3.5 mm mini-Phoenix to the power supply.

Using the Ethernet port for power (PoE)

Connect your CAT5/CAT6 Ethernet cable to the por t shown in FIG. 2. (See the

Mio

Modero DMS & Mio Modero DMS Pinnacle

instruction manual for an illustration and

cable pinouts).

Mounting Procedures

FIG. 3 shows the mounting dimensions for the Mio Modero DMS. Reference these
measurements when planning and installing the device. Consult the

Mio Modero DMS

& Mio Modero DMS Pinnacle

instruction manual for other installation methods.

FIG. 1

Mio Modero DMS Device Family

Mio Modero DMS (FG2408-01XX) Specifications

Power 12 VDC / PoE:

Maximum power consumption (PoE):

• 5.5 Watts

Maximum startup (rush) current (PoE):

• 150 mA @ 50 VDC

Maximum continuous current (PoE):

• 100 mA @ 50 VDC

Maximum power consumption (DC):

• 5.0 Watts

Maximum startup (rush) current (DC):

• 525 mA @ 13.5 VDC

Maximum continuous current (DC):

• 350 mA @ 13.5 VDC

Front Panel Components:

• LCD display
• 8 pushbuttons

Rear Panel Connectors:

• Ethernet Port (PoE)
• 2-pin 3.5 mm mini-Phoenix (female) connector

Dimensions (HWD):

• 4.50 (114.3 mm) x 3.50 (91.4 mm) x 2.88 (73 mm)

Supported Fonts:

Only True Type Fonts

Weight (range):

• Device - .45 lbs (.20 kg)
• Back box - .20 lbs (.09 kg)

Operating Environment:

• Operating Temperature: 0° to 40° C (32° to 104° F)
• Storage Temperature: -10° to 60° C (14° to 140° F)

Mounting:

The Mio Modero DMS is installed in one of two ways:

• 4 screws for hard surface mounting
• 2 expansion clips for pressure mounting

Available Color Schemes:

Black (BL), White (WH), Beige (BG), Almond (AL),
Brown (BR), Gray (GR), Ivory (IV), Light Almond (LA),
Taupe (TP), Gold (GL), Silver (SL)

Included Accessories:

• 2-pin 3.5 mm mini-Phoenix connector (

41-5025

)

• Mounting kit (

KA2250-01

)

Menu Up

Menu select
pushbuttons

Menu Down

Menu items

FIG. 2

Mio Modero DMS Rear Components

2-pin
3.5 mm

(female)

Ethernet Port

Board Orientation

Notch
This notch coincides

with an indentation in

the back box. The

notch is always on the

left.

Device Removal Notch
This notch coincides with

a metal tab on the back box.

The metal tab prevents damage

to installation surfaces.

(Front View)

(PoE)

connector

mini-Phoenix