AMX AXB-TM5 - Manual - manualsarea.com

Page 2 - AMX Limited Warranty and Disclaimer; determination of rights.

AMX Limited Warranty and Disclaimer AMX Corporation warrants its products to be free of defects in material and workmanship under normal use for three (3) years from the date of purchase from AMX Corporation, with the following exceptions: • Electroluminescent and LCD Control Panels are warranted fo...

Page 3 - Table of Contents

Table of Contents i AXB-TM5 Television Manager Table of Contents Product Information ................................................................................................. 1 Front Panel ..........................................................................................................

Page 5 - Product Information; Front Panel; The following table details the specifications for the AXB-TM5.; Specifications

Product Information 1 AXB-TM5 Television Manager Product Information The AXB-TM5 Television Manager is a microprocessor-based television controller. The AXB-TM5 can be configured as a peripheral on the AXlink. As part of an Axcess Control System, provides media source selection and management via re...

Page 7 - Connection and Wiring; Device DIP Switch; Device DIP switch positions and their values.; Device DIP switch settings

Connection and Wiring 3 AXB-TM5 Television Manager Connection and Wiring Device DIP Switch The eight-position Device DIP switch, shown in FIG. 2, sets the AXlink device number. Every device on the bus must have a unique device code. An eight-position DIP switch is used to set the device number for t...

Page 8 - Wiring the Rear Panel; Preparing/connecting captive wires; Wiring Guidelines @ 200 mA

Connection and Wiring 4 AXB-TM5 Television Manager Wiring the Rear Panel Preparing/connecting captive wires You will need a wire stripper and flat-blade screwdriver to prepare and connect the captive wires. 1. Strip 0.25 inch of wire insulation off all wires. 2. Insert each wire into the appropriate...

Page 9 - CC-IRC emitter wiring connections

Connection and Wiring 5 AXB-TM5 Television Manager CC-IRC emitter wiring connections FIG. 4 shows how to connect a CC-IRC IR Emitter to the IR Emitter connector on the AXB-TM5. IR emitter to device installation The following steps describe the installation of the IR emitter to the television IR wind...

Page 10 - TV sensor connections; AXlink data and 12 VDC power supply connections

Connection and Wiring 6 AXB-TM5 Television Manager 4. Attach the IR shield, with IR emitter diode, to the television IR window, ensuring that the IR emitter diode is properly positioned in the television input IR window. 5. Press firmly to activate the pressure-sensitive adhesive of the IR shield. T...

Page 11 - the limits described in the

Connection and Wiring 7 AXB-TM5 Television Manager Use a 12 VDC power supply when the distance between the control system and AXB-TM5 exceeds the limits described in the Wiring Guidelines section on page 4. Make sure to connect only the GND wire on the AXlink connector when using a 12 VDC power supp...

Page 13 - AXCESS Programming Guide; Channel Setting Commands; Device Assignment; AXB-TM5 Channel Settings

Programming 9 AXB-TM5 Television Manager Programming You can program the AXB-TM5 to perform a wide variety of operations using Axcess Send_Commands. This section describes channel settings, IR functions, and system Send_Commands. Refer to the AXCESS Programming Guide for additional programming infor...

Page 14 - perform various operations.

Programming 10 AXB-TM5 Television Manager System Send_Commands System Send_Commands are stored in the Axcess Control System and direct the AXB-TM5 to perform various operations. System Send_Commands Command Description 'CARON' Turns the IR carrier On (default). Example: SEND_COMMAND AXBTMX,'CARON' '...

AMX AXB-TM5 - Manual

Table of Contents:

Summary

Other AMX Models