American Standard T506.740 - Manual

American Standard T506.740 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

Page 2 – Remove check stops and re-install them transposed.; Assemble HANDLES and TRIM.; TOP; TRIM INSTALLATION
Page 3 – Figure 1
Page 4 – M O M E N T S; MODEL NUMBER; CAP; ESCUTCHEON; HANDLE SCREW; C E N T R A L T H E R M O S TAT; ADAPTER; appropriate finish code
Page 5 – MESURES RELATIVES AUX POINTS DE RACCORDEMENT; Outils recommandés; Tournevis à lame plate; INSTRUCTIONS D’ENTRETIEN :; T H E R M O S TAT C E N T R A L; ENTRÉES 1⁄2 po NPT
Page 6 – Retirer les butées de vérification et les inverser.; Assembler les POIGNÉES et la garniture.; Remarque importante; : La BUTÉE DE VÉRIFICATION ROUGE est maintenant à droite; INSTALLATION DE LA GARNITURE
Page 8 – NUMÉRO DU MODÈLE
Page 9 – DIMENSIONES DE INSTALACIÓN; Herramientas recomendadas; Destornillador de punta plana; DEBE; INSTRUCCIONES PARA EL CUIDADO:; T E R M O S TAT O C E N T R A L
Page 10 – INSTALACIÓN DE LA MOLDURA
Page 11 – Figura 1
Page 12 – NÚMERO DE MODELO

Loading the manual

M O M E N T S

T 5 0 6 . 7 4 0

Installation

Instr uctions

M 9 6 8 0 2 6

Thank you for selecting American-Standard...the

benchmark of fine quality for over 100 years.

To ensure that your installation proceeds smoothly--please

read these instructions carefully before you begin.

Certified to comply with ANSI A112.18.1M
ASSE 1016

ROUGHING-IN DIMENSIONS

Recommended Tools

Flat Blade Screwdriver

Phillips Screwdriver

Remove as much surface dirt and film using clear
water and soft cotton cloth

(as described above)

Use any of the following to remove tough surface
film and build-up:
Mild liquid detergents
Clear ammonia free liquid glass cleaners
Non-acidic, non-abrasive gentle liquid or fully
dissolved powder cleansers mixed according to
manufacturers directions.
Non-abrasive liquid polishers

Once clean, rinse faucet again with clear water to
thoroughly remove cleaner or polish and blot dry with
a soft cotton cloth.

To keep your new faucet looking new, please follow
these simple care instructions:

DO:

Simply rinse the faucet clean with clear water.

Dry the faucet with a soft cotton cloth.

DO NOT:

Do not use any abrasive cleaners, cloths, or
paper towels.
Do not use any cleaning agents containing
acids, polish abrasives, or harsh cleaners or
soaps.

Regular and routine cleaning will reduce the need for
heavy cleaning and polishing. If heavy cleaning is
required, the following procedures are recommended:

CARE INSTRUCTIONS:

Failure to follow these care instructions may
damage the Faucet's finish.

C E N T R A L T H E R M O S TAT

W I T H V O L U M E C O N T R O L

T R I M K I T

186mm

(7-3/8)

100mm

(3-7/8)

220mm

(8-5/8)

48mm to 68mm

(2 to 2-5/8)

170mm

(6-3/4)

NOTE: FITTING

MUST BE INSTALLED

WITH VOLUME CONTROL

ON TOP.

R520

1/2" NPT INLETS

R540

3/4" NPT INLETS

25mm

(1)

FINISHED

WALL

160mm

(6-1/4)

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - Remove check stops and re-install them transposed.; Assemble HANDLES and TRIM.; TOP; TRIM INSTALLATION

M 9 6 8 0 2 6 1 2 INSTALL HANDLES Should the hot and cold water supply pipes have been transposed makingadjustment impossible, proceed as follows: TRANSPOSED SUPPLY PIPING OR BACK TO BACK INSTALLATION 3 Remove check stops and re-install them transposed. Shut off water supply.Remove handle and rim. (...

Page 3 - Figure 1

M 9 6 8 0 2 6 3 3 4 TEMPERATURE ADJUSTMENT SET HOT LIMIT STOP Check that arrow marking B points to the 12 o'clock position. If not, push the BLACK CLAMP on the SECURING RING tothe right, pull off KNOB MOUNT (3) and reinstall KNOB MOUNT (3) with arrow "B" 12 o'clock position. See Figure 1. Fo...

Page 4 - M O M E N T S; MODEL NUMBER; CAP; ESCUTCHEON; HANDLE SCREW; C E N T R A L T H E R M O S TAT; ADAPTER; appropriate finish code

M O M E N T S M 9 6 8 0 2 6 MODEL NUMBER A907090-YYY0A CAP M908024-YYY0A ESCUTCHEON M909438-YYY0A HANDLE SCREW M962727-YYY0A HANDLE KIT C E N T R A L T H E R M O S TAT W I T H V O L U M E C O N T R O L T R I M K I T For toll-free information and answers to your questions, call: 1-800-442-1902 Weekda...