American Standard T010.740 - Manual
American Standard T010.740 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – TOP; TRIM INSTALLATION; Remove check stops and re-install them transposed.; Assemble HANDLES and TRIM.
- Page 3 – Figure 1
- Page 4 – MODEL NUMBER; C E N T R A L T H E R M O S TAT; G R E E N T E A
- Page 5 – MESURES RELATIVES AUX POINTS DE RACCORDEMENT; Outils recommandés; À FAIRE; INSTRUCTIONS D’ENTRETIEN :; T H E R M O S TAT C E N T R A L
- Page 6 – Retirer les butées de vérification et les inverser.; Assembler les POIGNÉES et la garniture.
- Page 8 – NUMÉRO DU MODÈLE; PLAQUE DE FIXATION
- Page 9 – Instr ucciones; DIMENSIONES DE INSTALACIÓN; Herramientas recomendadas; INSTRUCCIONES PARA EL CUIDADO:; T E R M O S TAT O C E N T R A L; PARED
- Page 10 – INSTALACIÓN DE LA MOLDURA
- Page 11 – paso 2; Figura 1
- Page 12 – NÚMERO DE MODELO
G R E E N T E A
T 0 1 0 . 7 4 0
Installation
Instr uctions
M 9 6 8 0 2 2
Thank you for selecting American-Standard...the
benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly
please read these instructions carefully before you begin.
Certified to comply with ANSI A112.18.1M
ASSE 1016
ROUGHING-IN DIMENSIONS
Recommended Tools
Flat Blade Screwdriver
Phillips Screwdriver
Remove as much surface dirt and film using clear
water and soft cotton cloth
(as described above)
.
Use any of the following to remove tough surface
film and build-up:
Mild liquid detergents
Clear ammonia free liquid glass cleaners
Non-acidic, non-abrasive gentle liquid or fully
dissolved powder cleansers mixed according to
manufacturers directions.
Non-abrasive liquid polishers
Once clean, rinse faucet again with clear water to
thoroughly remove cleaner or polish and blot dry with
a soft cotton cloth.
To keep your new faucet looking new, please follow
these simple care instructions:
DO:
Simply rinse the faucet clean with clear water.
Dry the faucet with a soft cotton cloth.
DO NOT:
Do not use any abrasive cleaners, cloths, or
paper towels.
Do not use any cleaning agents containing
acids, polish abrasives, or harsh cleaners or
soaps.
Regular and routine cleaning will reduce the need for
heavy cleaning and polishing. If heavy cleaning is
required, the following procedures are recommended:
CARE INSTRUCTIONS:
Failure to follow these care instructions may
damage the Faucet's finish.
C E N T R A L T H E R M O S TAT
W I T H V O L U M E C O N T R O L
T R I M K I T
186mm
(7-3/8)
100mm
(3-7/8)
200mm
(7-7/8)
48mm to 68mm
(2 to 2-5/8)
150mm
(6)
NOTE: FITTING
MUST BE INSTALLED
WITH VOLUME CONTROL
ON TOP.
R520
1/2" NPT INLETS
or
R540
3/4" NPT INLETS
25mm
(1)
FINISHED
WALL
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
TOP M 9 6 8 0 2 2 1 Remove PLASTER GUARD (1) if attached. Push CAPS (2 & 2a) as shown onto CONTROL VALVES (3) . Push ESCUTCHEON HOLDER (4) with lightly greased O-RING SEALS (5) over CAPS (2, 2a) . Attach the FIXATION PLATE (7) to the ESCUTCHEON HOLDER (4) with the two SCREWS (6) provided. Push E...
M 9 6 8 0 2 2 4 4 4 TEMPERATURE ADJUSTMENT SET HOT LIMIT STOP Check that arrow marking B points to the 12 o'clock position. If not, push the BLACK CLAMP on the SECURING RING tothe right, pull off KNOB MOUNT (4) and reinstall KNOB MOUNT (4) with arrow "B" 12 o'clock position. See Figure 1. Fo...
M 9 6 8 0 2 2 MODEL NUMBER A907090-YYY0A CAP M962630-0070A ESCUTCHEON HOLDER M907712-YYY0A ESCUTCHEON M918318-0070A HANDLE SCREW M962731-YYY0A HANDLE KIT C E N T R A L T H E R M O S TAT W I T H V O L U M E C O N T R O L T R I M K I T T 0 1 0 . 7 4 0 G R E E N T E A For toll-free information and answ...
