American Standard SERIES 7193 - Manual

L A K E L A N D ™ K I T C H E N S I N K S

S E R I E S 7 1 9 3

I n s t a l l a t i o n
I n s t r u c t i o n s

7 9 1 3 9 3 - 1 0 0 R e v . A

Thank you for selecting American-Standard...the benchmark of fine quality
for over 100 years. To ensure that your installation proceeds smoothly--
please read these instructions carefully before you begin.

B E F O R E Y O U B E G I N . . .

33"

(838mm)

LAKELAND SINGLE BOWL

MODEL 7193 SELF RIMMING

COUNTERTOP CUTOUT FOR

NEW INSTALLATIONS

A M E R I C A S T B R A N D

S E L F R I M M I N G

SINK
OUTLINE

CUTTING LINE

1" R (25mm) TYP.

Certified to comply with ANSI A112.19.4.M
U.S. Patent No. 4,664,982
Other patents pending.
CAN/C.S.A. B-45
Observe local plumbing and building codes.

I M P O R T A N T : D I M E N S I O N O F F I X T U R E S A R E N O M I N A L A N D M A Y V A R Y W I T H I N
T H E R A N G E O F T O L E R A N C E S E S T A B L I S H E D B Y A . N . S . I . A N D C . S . A . S T A N D A R D S

.

®

© A M E R I C A N S T A N D A R D I N C . 2 0 0 5

™

Unpack new sink and inspect carefully for damage.
Replace the sink in its original packing carton to
protect it until you are ready to begin installation.

Refer to American Standard roughing-in information for

specific dimensions for each model.

Recommended Tools & Materials

Silicone Sealant
Putty Knife
Pipe Wrench
Channel Locks
Phillips Screwdriver
Regular Screwdriver
Adjustable Wrench

Drill
Basin Wrench
Saber Saw
Tubing Cutter
Tape Measure
Hacksaw
Mineral Spirits

22"

(559mm)

5/8"

(16mm)

1-5/8" (16mm)

COUNTERTOP MOUNTED FAUCET

MODEL 7193 UNDER COUNTER MOUNT

LAKELAND SINGLE BOWL

33"

(838mm)

LAKELAND SINGLE BOWL

MODEL 7193 SELF RIMMING

COUNTERTOP CUTOUT FOR

REPLACEMENT INSTALLATIONS

SINK
OUTLINE

CUTTING LINE

1" R (25mm) TYP.

22"

(559mm)

5/8"

(16mm)

5/8" to 1-5/8"
(16 to 41mm)

CUTOUT DIMENSIONS FOR SINKS:

Below are the dimensions needed to determine the cutout size for your
installation. Select the correct diagram for your application and refer to the
instructions below.

Locate and mark center lines of sink on countertop.

Provide proper clearance under the countertop for the faucet supply lines and
the structural parts of the cabinet.

By using the diagrams below and measuring your sink, draw the outline of
the sink onto the countertop. This is not the cutting outline.

Refer to the diagram for your sink and draw a line the required distance in
from the sink outline. Cut on this line.

CAUTION:

1. Recommended Minimum Countertop Thickness Wood 19mm (3/4") Marble and Solid Surface 12mm (1/2")

2. Prior to cutting countertop ensure that the faucet shank has sufficient length to attach the mounting nut after
the shank goes through both the countertop and the sink deck. The deck is 10mm (3/8") thick.

NOTE:

Undercounter Installations of sinks should be done by trained and experienced installers due to the materials (such

as marble, hard synthetics, etc.). Contact your countertop distributor for best method of cutting the opening.

27-3/8"

(695mm)

COUNTERTOP CUTOUT FOR

UNDERCOUNTER INSTALLATIONS

2-5/16" R (19mm) TYP.

16-7/8"

(429mm)

CUTOUT

SUPPORT
CLIPS

SINK MOUNTED FAUCET

MODEL 7193 UNDER COUNTER MOUNT

LAKELAND SINGLE BOWL

29-1/2"

(749mm)

3/4" R (19mm) TYP.

20-1/2"

(521mm)

CUTOUT

SUPPORT
CLIPS