American Standard Saver Bath Walls - Manual
American Standard Saver Bath Walls – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Rough plumbing and fittings must be installed before walls.
- Page 3 – INSTALLATION PROCEDURES:; attach board butting up to the top of the pocket. Allow time to cure.; Nailing; Nailing flange; Top Nailing flange
- Page 6 – Green Board
- Page 7 – WARNING; HARSH CHEMICALS SHOULD NEVER BE USED ON SHOWER WALL SURFACE.; Clean after use with a mild liquid household; Do not wax areas where you walk or stand.; In the United States:
7 5 4 74 8 - 10 0 R e v. C
P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A S A m e r i c a I n c .
© A S A m e r i c a I n c . 2 0 1 2
NOTE: Take extra care in handling the front surfaces of the walls. Use only non-abrasive cloths to avoid scratching.
Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this product is installed
properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be
sure your installation conforms to local codes.
INSTALLATION INSTRUCTIONS
SAVER
™
BATH WALLS
MODEL: 2649BW
USE BATH WALL 2649BW WITH BATH TUB 2647.102 or 2647.202
REQUIRED TOOLS AND MATERIALS
BEFORE YOU BEGIN....
Local building codes vary by location. Observe all local plumbing and building codes.
Unpack your new shower walls and inspect them carefully for damage. Verify that the walls are the correct size for your
installation. Refer to American Standard roughing-in information for specific dimensions for each model.
Tape Measure
Caulking Gun
Level
Square
Pencil
Drill
Hole Saw or
Sabre Saw
TOOLS:
Acrylic/Latex or Acrylic/Silicone Sealant
Galvanized (or corrosion resistant) flat head screws 3/4" minimum length
2 x 4 lumber for additional wall studs as required
Tub Surround Adhesive
1 x 4’s if installing shower doors
MATERIALS:
PREPARATION:
Saver
™
bath tub walls are to be installed directly
over stud walls. Drywall is not required.
A)
Remove dry wall surface and ensure that
alcove is plumb and square. (Illustration 1)
B)
Identify your model number in the illustrations
which follow. Prepare studs as indicated.
Illustration 1
Each alcove
stud must
be plumb
and square.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 7 5 4 74 8 - 10 0 R e v. C Installation for use with tub Model# 2647.202 The studs should be located as shown to properly support walls. Provide additional studs where illustrated. (below) 8-1/4" (210mm) 8-1/4" (210mm) 30" (762mm) 6"(152mm) 12" (305mm) 60" (1524mm) 9-1/4...
3 7 5 4 74 8 - 10 0 R e v. C 1 2 INSTALLATION PROCEDURES: If you plan to install a bath/shower door, a 1 x 4 must be installed in the pocket on the back of both side walls. A) Cut one end of the 1 x 4 to 45° as shown. (Fig.1) Then cut the 1 x 4 to a length of 57-1/2". B) Apply a bead of tub surr...
7 5 4 74 8 - 1 0 0 R e v. C 6 7 6 Install temporary braces to hold the center of the back and side panels tight to the studs for approximately 24 hours while adhesive sets. Add cushioning between panels and braces to prevent scratching the panels. When installing greenboard, position drywall screws ...
