American Standard 7431.801 - Manual
American Standard 7431.801 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – VALVE OUTLET SUPPLY CONNECTION; as illustrated so they do not kink.; COLD; VALVE INSTALLATION
- Page 4 – NOTE: FLEXIBLE SUPPLIES OR BULL-NOSE RISERS MUST BE
- Page 5 – CONVERT TO A FIXED SPOUT IF DESIRED.
- Page 6 – Speed ConnectTM Drain; Troubleshooting Guide; CABLE ADJUSTMENT PROCEDURE; If Stopper does not raise up fully or sink drains too slowly:; STOPPER REMOVAL PROCEDURE
- Page 7 – STOPPER INSTALLATION PROCEDURE; rear; “Locked”; front; “Unlocked”; Unlocked Mode
- Page 8 – BERWICK; S P R E A D; M O D E L N U M B E R; appropriate finish code
1
2
5
4
GROOVE
(FAUCET
BASE)
MOUNTING
SURFACE
3
8
Figure A
M 9 6 8 6 4 0 R E V . 1 . 1
7 4 3 0 . 8 2 1
7 4 3 0 . 8 0 1
7 4 3 1 . 8 2 1
7 4 3 1 . 8 0 1
Certified to comply with ANSI A112.18.1
Installation
Instr uctions
S P R E A D L AVAT O R Y F A U C E T
w i t h
Speed Connect™ Drain
Adjustable Wrench
Screwdriver
Channel Locks
Recommended tools
Tubing Cutter
1
INSTALL FAUCET
NOTE: READ STEP #16 BEFORE INSTALLING SPOUT TO CONVERT FROM SWIVEL TO FIXED SPOUT.
Turn off hot and cold water
supplies before beginning.
CAUTION
7430.801
7430.821
7431.801
7431.821
1
BERWICK
™
/ BOULEVARD
™
COLLAR ON
MOUNTING NUT
6
4
Figure B
Seat SEAL
(1)
into under side of SPOUT BASE
(2)
.
Feed FAUCET SUPPLIES
(3)
, MOUNTING STUD
(4)
and DRAIN
CABLE ASSEMBLY
(8)
through the mounting hole of lavatory or
mounting surface.
Figure A.
7
5
9
From below, slide DRAIN CABLE ASSEMBLY
(8)
and FAUCET SUPPLIES
(3)
through opening in the SPACER
(9)
against underside of deck.
Figure B.
Note: For thick deck installaitons the SPACER
(9)
is not required.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
Congratulations on purchasing your American Standard
faucet with Speed Connect drain, a feature found only on
American Standard faucets.
*Your new American Standard faucet is designed to work only with the Speed Connect drain.
Speed Connect Drain*
• Fewer parts, installs in less time
• Never needs adjustment
• Guaranteed to seal properly the first time, every time.
From below, push GASKET
(7)
and RETAINING WASHER
(5)
onto
MOUNTING STUD
(4)
. Secure Faucet with MOUNTING NUT
(6)
,
pulling faucet to front of sink, so SUPPLIES
(3)
rests against
mounting hole. Before final tightening, make sure collar on
MOUNTING NUT
(6)
is seated into RETAINING WASHER
(5)
.
Figure B.
Adjust Faucet so that it is centered. Tighten MOUNTING NUT
(6)
to complete faucet mounting.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 1 VALVE OUTLET SUPPLY CONNECTION 3 RED BAND BLUE BAND Connect Red Banded Hose to Left Valve and Blue Banded Hose to Right Valve. Attach COUPLING NUTS (1) of SUPPLY HOSES (2) and tighten making water tight connection. Important: Loop SUPPLY HOSES (2) as illustrated so they do not kink. COLD HOT VAL...
M 9 6 8 6 4 0 R E V . 1 . 1 Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes. Note: If STOPPER (2) does not open and close properly then refer to the “troubleshooting section” of these instructions. CHECK OPERATION OF POP-UP 11 2 MAKE WATER SUPPLY AND WASTE CONNECTIONS 12 Thread CAB...
M 9 6 8 6 4 0 R E V . 1 . 1 5 To change direction of handle rotation, proceed as follows: Turn valve to OFF position.Thread counter-clock wiseHANDLE BASE (1) to remove HANDLE ASSEMBLY (2) from ESCUTCHEON BASE (3) . Use a flat blade screw driverto remove SPRING CLIP (4) . Lift STOP WASHER (5) , turn ...
