American Standard 4454 - Manual
American Standard 4454 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – MAKE WATER SUPPLY CONNECTIONS; COLD
- Page 3 – A E R A T O R
- Page 4 – MODEL NUMBERS; E L I T E
4453 SERIES
4454 SERIES
E L I T E
I n s t a l l a t i o n
I n s t r u c t i o n s
M 9 6 8 2 0 2 R E V . 1 . 2
Certified to comply with ANSI A112.18.1M
1
INSTALL FAUCET WITH OR WITHOUT DECK ESCUTCHEON
CAUTION
Turn off hot and cold water
supplies before beginning.
SINGLE CONTROL KITCHEN FAUCET
and HAND SPRAY
1
2
8
A
B
P U T T Y
S P O U T B A S E
S P O U T B A S E
S Q U A R E
S E A L R I N G
8
S Q U A R E
S E A L R I N G
4
S I N K O R
M O U N T I N G
S U R F A C E
2
3
4
5
6
7
9
3
0
1
2
3
4
5
6
Assemble RUBBER WASHER
(5)
, BRASS WASHER
(6)
, and threaded LOCKNUT
(7)
onto SHANK
(4)
from underside
of sink or mounting surface. Hand tighten LOCKNUT
(7)
and check that rotation of HANDLE
(8)
from HOT to COLD
is centered.
Use a screwdriver to tighten SCREWS
(9)
on LOCKNUT
(7)
. Work your way around LOCKNUT
(7)
, tightening
the screws slightly each time until all are snug to ensure even pressure.
(A) Installation with ESCUTCHEON (1)
.
Apply a bead of putty to bottom edge of ESCUTCHEON WITH PUTTY PLATE
(1)
.
Insert supply HOSES
(3)
and SHANK
(4)
through hole of ESCUTCHEON WITH PUTTY PLATE
(1)
and mounting surface.
Make certain the SQUARE SEAL RING
(2)
is properly seated in recess of SPOUT BASE. Follow mounting instructions below
to secure faucet to mounting surface.
(B) Installation less ESCUTCHEON (1)
.
Remove ESCUTCHEON WITH PUTTY PLATE
(1)
and Insert supply HOSES
(3)
and
SHANK
(4)
through mounting hole and seat SPOUT BASE onto sink or mounting surface. Make certain the SQUARE SEAL
RING
(2)
is properly seated in recess of SPOUT BASE. Do not use putty.
CARE:
5
6
7
9
Thank you for selecting American-Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--
please read these instructions carefully before you begin.
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
TOOLS REQUIRED
Plumbers' Putty or Caulking
Adjustable Wrench
Channel Locks
Regular Screwdriver
Phillips Screwdriver
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
On model with separate spray, place the SPRAY HOLDER (1) into the appropriate mounting hole. Assemble the SPRAYHOLDER WING NUT (2) onto the shank of SPRAY HOLDER (1) from below and tighten. Do not use putty. On model with spray through the ESCUTCHEON (3) , place SPRAY HOLDER (4) into the hole of ESC...
5 TEST INSTALLED FAUCET Move HANDLE down into "off" position and remove AERATOR. Turn on water supplies and check connections for leaks . Operate HANDLE up and down, left and right to flush water lines thoroughly.For faucet with spray, direct SPRAY HEAD into sink and activate SPRAY. Check ho...
MODEL NUMBERS 4453 SERIES4454 SERIES E L I T E S I N G L E C O N T R O L K I T C H E NF A U C E T w i t h H A N D S P R AY M909320-YYY0A SPOUT FLANGE 042850-0070A DIVERTER 060366-0070A SPOUT SEAL KIT 921877-0070A CAP RETAINER 060485-YYY0A ESCUTCHEON 060484-YYY0A ESCUTCHEON WITHSPRAY HOLE 030760-YYY0...
