Alcatel T25-CE - Manual

Alcatel Logo and Alcatel name are trademarks of Alcatel and used under

license by Thomson.

T25-CE

T25-CE

TROUBLESHOOTING TIPS

PROBLEM

SOLUTION

No dial tone

Can’t dial out

•

Check hook switch to make sure it pops up.

•

Make sure TONE/PULSE is set to correct position.

•

Unplug the phone, wait 30 seconds, and plug

the phone back in.

Phone doesn’t

ring

•

Check phone line cord.

•

Could have too many phones on one line. (The total

REN of all phones should not be greater than the

maximum REN for your area, Usually 5.)

CARE AND MAINTENANCE

To keep your phone working and looking good, please follow these

guidelines:

• Avoid putting near heating appliances and devices that generate

electrical noise (for example, motors and fluorescent lamps).

• DO NOT expose to direct sunlight or moisture.

• Avoid dropping and other rough treatment of the unit.

• Never use a strong cleaning agent or abrasive powder because

this will damage the finish.

• Retain the original package in case you need to return is at a later

date.

Used equipment must be disposed of in compliance

with current environmental protection regulations.

You should return it to your reseller or dispose of it in an

approved recycling centre.

INTRODUCTION

Your telephone is designed to give you flexibility in use, and high

quality performance. To get the most from your new telephone, we

suggest that you take a few minutes right now to read through this

User’s Tips.

If you have any questions or problems, consult the Troubleshooting

Tips for the solution.

PARTS CHECKLIST

Your package should contain the following items:

Base Handset Coiled cord Line cord

INSTALLATION AND SETUP

You GE telephone can be mounted on the wall or placed on a

table. After you decide which type of installation you want, refer to

the appropriate installation diagram.

BEFORE YOU BEGIN

MODULAR JACK REQUIREMENTS

You need a RJ11C type modular jack, which is the most

common type of phone jack and might look like one

pictured here. If you don’t have a modular jack, call your

local phone company to find out how to get one installed.

Modular telephone line jack

DESKTOP INSTALLATION

1. Adjust the

RINGER

volume switch to the desired setting. Default

setting is HI.

2. Set the PULSE/TONE switch to TONE if you use Touch-Tone Service;

Set it to PULSE

if you have rotary service. Default setting is

TONE.

3. Set the Flash time switch (600ms, 300ms, 100ms) to the appropriate

setting.

Default setting is

600ms.

4. Plug the handset cord into the handset, and into the telephone

jack on the left side of the unit.

5. Plug the telephone line cord into a modular jack (RJ11C) and into

the LINE jack on the back of the unit.

6. Place the handset to base cradle.

WALL MOUNT INSTALLATION

The telephone can be mounted on a wall phone plate (not included).

1. Adjust the wall mount knob on cradle of base of apply to wall

mount.

2. Set the RINGER VOLUME

switch to the desired setting. Default

setting is HI.

3. Set the PULSE/TONE switch to TONE if you use Touch-Tone service:

set it to PULSE

if you have rotary service. Default setting is

TONE.

4. Set the Flash time switch (600ms,300ms,100ms) to the appropriate

setting. Default setting is

600ms.

5. Adjust the wall hook on cradle of base to apply to wall mount.

6. Plug the phone cord into the phone jack on the back of the unit.

7. Connect the phone cord to the modular jack on the wall.

8. Place the base to the wall mount plate.

9. Plug the handset cord into the handset and into the unit, and then

hang up the phone.

Use/Ring indicator

USING FEATURES

MAKING A CALL

1. Lift the handset and wait for a dial tone.

2. Dial the telephone number using the keypad.

RECEIVING A CALL

Lift the handset to answer the call.

RINGER VOLUME CONTROL

Use the RINGER volume switch on the back of the base to adjust the

volume of the ringer.

FLASH BUTTON

Press the FLASH button instead of using the hook switch to activate

customer calling services such as call waiting or call transfer, which

are provided by your local phone company.

REDIAL BUTTON

Redial the last number you called by pressing the REDIAL button after

you get a dial tone. Maximum digits of redial is 32.

Wall plate

9

180

℃

Flash button

Redial button

“WEEE” Weight: 0.452Kg

DOC