Page 3 - Contents
3 Contents Introduction 4 Extraction mode 4 Recirculation mode 5 Electrical connections 6 Technical details 7 Installation 8 Safety warnings for kitchen unit installer 8 Wall unit mounting 10 Wall mounting 11 Hood operation 12 Safety warnings for user 13 Maintenance and care 14 Opening the grid 14 G...
Page 4 - Introduction; Extraction mode
4 2 Introduction Extraction mode ● The hood is supplied as an extractor unit and can also be used with a filtering function by fitting activated carbon filters (available as an accessory). ● The unit features two outlet holes, one of which A is located on the top of the unit while the other B is loc...
Page 6 - Electrical connection
6 Electrical connection 220-240 V - using fixed power supply line with plug. (The unit should only be connected up by an authorized electrician). Your appliance must be connected to fixed wiring via the use of a double pole swiched fused spur outlet with or without pilot lamp.We strongly recommend t...
Page 7 - Technical details
7 Technical details DimensionsHeight x Width x Depth (in cm) 13 x 59,9 x 51 Weight Net: 6,9 kg Gross: 7,8 kg Maximum absorbed power: 205 W Motor absorption 1 x 125 W Lighting: 2 x 40 W Length of the cable: 110 cm Fan powers (speed), speed in compliance with DIN 44971 Extraction mode Speed 1 115 m 3 ...
Page 8 - Installation; Safety warnings for kitchen unit installer
8 Installation Safety warnings for kitchen unit installer ● When used as an extractor unit, the hood must be fitted with a 120mm diameter hose. ● If the fumes must be forced out through the wall, you must obtain a MKZ sizable wall exhaust pipe (with external exhaust and air intake), E-Nr.- 610 899 0...
Page 10 - Wall unit mounting
10 Wall unit mounting ● Make the holes on the bottom of the cupboard, using the drilling template . ● From inside the cupboard, insert the 4 supplied screws and tighten them in the appropriate holes on the appliance. Fig. 4. 4
Page 11 - Wall mounting
11 Wall mounting ● Fix the drilling template to the wall. ● Make 3 Ø 8mm holes in the wall 2 at points I , 1 as desired at points L . ● Insert the three Ø 8mm expansion plugs into the wall. ● Insert 2 5x45 screws at points I but do not tighten them completely. ● Adjust the unit so that it is positio...
Page 12 - Hood Operation
12 Hood Operation ● The hood is fitted with a variable speed motor. The most effective use of the hood is obtained by switching it on a few minutes before you start cooking and leaving it on a for approximately 15 minutes after you have finished, thus ensuring all cooking odours are eliminated. The ...
Page 13 - Safety warnings for user
13 ● Never leave a cooking hob or ring on without a pot or pan on top of it, to avoid the possibility of excess heat damaging the unit. Gas, oil in particular should never be left uncovered. ● Special care should be taken when using deep fat fryers since the oil in them can overheat and burst into f...
Page 14 - Maintenance and care; Opening the grid
14 6 Maintenance and care ● The hood must always be disconnected from the mains power supply before beginning any maintenance work. Opening the grid ● Open the latch L and swing the grille downwards. Fig. 6. ● To remove the grid, pull it forwards from the right and release it. Grease filter ● The ...
Page 16 - Cleaning
16 Warning ● Failure to observe the instructions on cleaning the unit and changing the filters will cause a fire hazard. You are therefore strongly recommended to follow these instructions. Changing the light bulb ● Disconnect the unit from the mains power supply. ● Remove the grid. ● Replace the ol...
Page 17 - What to do if
17 What to do if If your appliance fails to work properly please carry out the following checks. Symptom Solution The cooker hood will not start... Check that:The hood is connected to theelectricity supply.Check that the fan speed control isset to 1, 2 or 3. The cooker hood is not working Chec k tha...
Page 18 - Service and spare parts; C u s t o m e r C a r e
18 Service and spare parts In the event of your appliance requiring service, or if you wish topurchase spare parts, contact your local AEG Service Force Centre bytelephoning 08705 929 929 Your call will be automatically routed to the Service Centre coveringyour post code area.For the address of your...