Page 2 - Copyright Notice; rd Edition
FPM-2150 Series User Manual ii Copyright Notice This document is copyrighted by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements to the products described in this manual at any time. Specifications are thus subject to change without notice.No p...
Page 4 - FCC Class B; to which the receiver is connected
FPM-2150 Series User Manual iv FCC Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer-ence when the equipment is operated in...
Page 5 - Safety Instructions
v Packing List Before installing your equipment, make sure that the following materials have been received:• FPM-2150 Series flat panel monitor• Accessory pack, including: - AC/DC adapter- AC/DC power adapter bracket- Video signal cable, 1.8m- Fixed panel-mounted bracket x 10 pcs- Screw Bags (M4x25 ...
Page 7 - Wichtige Sicherheishinweise
vii DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech disclaims all responsibility for the accuracy of any statements contained herein. Wichtige Sicherheishinweise 1. Bitte lesen sie Sich diese Hinweise sorgfältig durch.2. Heben Sie diese Anleitung für den späteren Gebr...
Page 9 - Contents; Chapter
ix Table of Contents Contents Chapter 1 Introduction ..................................................... 2 1.1 Introduction ....................................................................... 2 1.2 Specifications .................................................................... 2 1.3 LCD Sp...
Page 11 - Introduction
2 CH APTER 1 Introduction This chapter includes:• Introduction• Specifications• LCD Specification• Power Consumption• Connectors• Dimensions
Page 12 - Chapter 1 Introduction; General; Heavy-duty steel chassis
FPM-2150 Series User Manual 2 Chapter 1 Introduction 1.1 Introduction Advantech's FPM-2150 Series consists of 15" color TFT LCD flat panel monitors built specifically for industrial applications. With the optional touchscreen, the FPM-2150 Series is an user-friendly system control interface.In a...
Page 13 - wire, analog resistive; LCD Specifications; Storage Temperature:
3 Chapter 1 • Vibration (operating): 5 ~ 17 Hz, double-amplitude displacement; 17 ~ 500 Hz, 1.0 G peak to peak • CE, FCC, BSMI, CCC certified• Power Consumption: +12V +/- 10% @ 2.5 A Touchscreen (Optional) • Type: 8 wire, analog resistive • Resolution: 1024 x 1024 • Light Transmission: 75% (Gouge Ha...
Page 14 - Power Adapter Specifications; The following connectors are on the bottom of the FPM-2150 Series:; DC 12V Power In; This connector connects to the DC 12V Switching Power Supply.
FPM-2150 Series User Manual 4 1.4 Power Adapter Specifications • Max Output Power: 42 Watts • AC input voltage: 100 - 240 V AC • Output voltage: + 12 V @ 3.5 A • Safety Standards: UL/CE/CCC/TUV/CB 1.5 Connectors The following connectors are on the bottom of the FPM-2150 Series: VGA Port (DB15) This ...
Page 17 - System Setup
2 CH APTER 2 System Setup • Mounting the Monitor• Wall / Panel / Rack Mounting• Desktop / Swing-Arm Mounting
Page 18 - Chapter 2 System Setup
FPM-2150 Series User Manual 8 Chapter 2 System Setup 2.1 Mounting FPM-2150 The FPM-2150 Series can be flexibly mounted. The versatility of the FPM-2150 mounts enable it to be mounted on your desk or almost any-where else. 2.1.1 Wall Mounting Please refer to figure 2.1 and follow the steps below to i...
Page 19 - Fasten the ten panel-mounting brackets with screws.
9 Chapter 2 2.1.2 Panel Mounting Refer to figure 2.2 and follow the instructions below to install in a panel.1. Place ten panel-mounting brackets on FPM-2150 (3 on the top, 3 on the bottom, 2 on the left, and 2 on the right). 2. Fasten the ten panel-mounting brackets with screws. 3. Mount FPM-2150 o...
Page 23 - APPENDIX
Page 24 - Appendix A Display Timing Mode & OSD; A.1 Supported Input Timing Modes; Note 1: Even if the preset timing is entered, some adjustment of func-
FPM-2150 Series User Manual 14 Appendix A Display Timing Mode & OSD A.1 Supported Input Timing Modes The different frequencies below are already programmed in this module, and the synchronous signal inputs are automatically recognized. Note 1: Even if the preset timing is entered, some adjustmen...
Page 25 - A.2 Keypad Interface
15 Appendix A A.2 Keypad Interface A.3 Power Indicator LED Status The keypad interface provides a driver for a dual color LED to indicate status.(1) Green: COMMON board detects a input signal and sends output sig-nal to LCD panel.(2) Orange: No signal detected, or out of range.(3) Green and blinking...
Page 26 - Main Menu Sub Menu
FPM-2150 Series User Manual 16 A.4 OSD Function Each selected value is stored into LCD memory after SEL signal input or time out. The stored values are not affected if the power is turned off. But the selected value is not available in case a selected mode is changed before time out or power is turn...
Page 27 - Touchscreen
2 APPENDIX B Touchscreen This appendix contains information on the touchscreen, its installation and configuration.
Page 28 - Appendix B Touchscreen; B.2 Touchscreen Specifications; Electrical; Hard coating is highly resistant to most solvents and chemicals
FPM-2150 Series User Manual 18 Appendix B Touchscreen B.1 Introduction The FPM-2150 Series’ optional touchscreen uses advanced 3M™ 8-wire resistive technology. It provides more accurate sensing capacity than other technologies. The touchscreen is specially designed for tough industrial environments,...
Page 29 - • Chemical strengthened glass with 4 H hardness standard.; B.3 Installing Driver for Windows 2000/XP
19 Appendix B Optical • Visible light transmission: 75% typical (>74% @ 550 nm test) • Clarity: Clear Finish - 25%, Antiglare Finish - 15% Sensor board • Chemical strengthened glass with 4 H hardness standard. (Test condition: ASTM D3363-92A) Ball drop test • Able to bear a 225 g steel ball dropp...
Page 32 - A License Agreement appears. Click “I accept...” and “Next”
FPM-2150 Series User Manual 22 4. A License Agreement appears. Click “I accept…” and “Next” 5. The “Ready to Install the Program” screen appears. Select “Install.”
Page 33 - The “InstallShield Wizard Completed” appears. Click “Finish.”
23 Appendix B 6. The next screen is “Hardware Installation.” Select “Continue Any-way.” 7. The “InstallShield Wizard Completed” appears. Click “Finish.”
Page 34 - B.4 Configuring PenMount Windows 2000/XP Driver; When the PenMount Control Panel appears, click “Calibrate.”; Calibrate
FPM-2150 Series User Manual 24 B.4 Configuring PenMount Windows 2000/XP Driver Upon rebooting, the computer automatically finds the new 9000 control-ler board. The touch screen is connected but not calibrated. Follow the procedures below to carry out calibration.1. After installation, click the PenM...
Page 38 - Draw; Click Clear Screen to clear the drawing.
FPM-2150 Series User Manual 28 Draw Tests or demonstrates the PenMount touch screen operation. The display shows touch location. Click Draw to start. Touch the screen with your finger or a stylus and the drawing screen registers touch activity such left, right, up, down, pen up, and pen down. Touch ...
Page 39 - Multiple Monitors; Check the; Enable Multiple Monitor Support; to assign touch controllers to displays.
29 Appendix B Multiple Monitors Multiple Monitors supports from two to six touch screen displays for one system. The PenMount drivers for Windows 2000/XP support Multiple Monitors. This function supports from two to six touch screen displays for one system. Each monitor requires its own PenMount tou...
Page 40 - When the mapping screen message appears, click OK.; mapping
FPM-2150 Series User Manual 30 2. When the mapping screen message appears, click OK. 3. Touch each screen as it displays “Please touch this monitor.” Fol-lowing this sequence and touching each screen is called mapping the touch screens .
Page 41 - Continue calibration for each monitor by clicking; bration; and touching the red squares.
31 Appendix B 4. Touching all screens completes the mapping and the desktop reap-pears on the monitors. 5. Select a display and execute the ‘Calibration’ function. A message to start calibration appears. Click OK. 6. “Touch this screen to start its calibration” appears on one of the screens. Touch t...
Page 42 - Option
FPM-2150 Series User Manual 32 Option This panel function supports two modes—Operation Mode and Beep Sound Mode—which allow configuration for specific touch screen appli-cations, such as point-of-sales (POS) terminals. NOTE: 1. If you used a single VGA output for multiple monitors, please do not use...
Page 43 - About
33 Appendix B About This panel displays information about the PenMount controller and driver version.
Page 44 - PenMount Monitor has the following functions.
FPM-2150 Series User Manual 34 B.4.2 PenMount Monitor Menu Icon The PenMount monitor icon (PM) appears in the menu bar of Windows 2000/XP system when you turn on PenMount Monitor in PenMount Util-ities. PenMount Monitor has the following functions. Beep Turns beep on or off. Right Button When you se...
Page 45 - Configuring the Rotate Function; Install the rotation software package.; party
35 Appendix B B.4.3 PenMount Rotating Functions The PenMount driver for Windows 2000/XP supports several display rotating software packages. Please see Chapter 5 for more information. The PenMount drivers for Windows 95, Windows 98/Me, Windows 2000/XP, as well as Windows 98 USB and Windows Me/2000/X...
Page 46 - B.5 Uninstall the PenMount Windows 2000/XP driver
FPM-2150 Series User Manual 36 B.5 Uninstall the PenMount Windows 2000/XP driver 1. Exit the PenMount monitor (PM) in the menu bar. 2. Go to Settings, then Control Panel, and then click Add/Remove program. Select PenMount DMC9000 and click the Add/Remove button. 3. Select PenMount DMC9000 and DMC910...
