Page 2 - Internet Access Router; Copyright; Disclaimer
Prestige 100WH Quick Start Guide ii Prestige 100WH Internet Access Router Copyright Copyright © 1998 by ZyXEL Communications Corporation. The contents of this publication may not be reproduced in any part or as a whole, transcribed, stored in a retrievalsystem, translated into any language, or trans...
Page 3 - Table of Contents
Prestige 100WH Quick Start Guide iii Table of Contents Chapter 1Before You Begin ................................................................................................................. 11.1 Purpose Of This Guide .................................................................................
Page 5 - Chapter 1; Purpose Of This Guide
Prestige 100WH Quick Start Guide 1 Chapter 1 Before You Begin 1.1 Purpose Of This Guide This guide provides instructions on how to setup your new Prestige and Windows 95/NTworkstations for Internet access using the Prestige Web Configurator (PWC). The Prestige Web Configurator provides a quick, simp...
Page 6 - Information From Your ISP; User name and password
Prestige 100WH Quick Start Guide 2 1.3 Information From Your ISP Your Internet Service Provider (ISP) should provide information needed to setup yourPrestige, usually in the form of an account configuration sheet. The information includes: l User name and password l ISP’s access phone number. l IP a...
Page 9 - Chapter 2
Prestige 100WH Quick Start Guide 5 Chapter 2 Cabling & Installation The following diagrams depict the cabling for the Prestige. After you have completed thecabling, proceed to Chapter 3: Windows 95 Quick Start or Chapter 4: Windows NT QuickStart. 2.1 Prestige 100WH Front Panel 2.1.1 Front Panel ...
Page 12 - Computer
Prestige 100WH Quick Start Guide 8 2.3 Prestige 100WH Connections POWER CONSOLE ETHERNET 4 3 2 1 WAN E t h e r n e t L A N Computer PowerAdapter PowerOutlet Modem / ISDN TA Modem orISDN TA PSTN/ISDN
Page 13 - Chapter 3
Prestige 100WH Quick Start Guide 9 Chapter 3 Windows 95 Quick Start This chapter shows you the step-by-step instructions to configure your Windows 95workstations for Internet access. 3.1 TCP/IP Installation You must first install TCP/IP protocol on each Windows 95 workstation before you can use itto...
Page 16 - The; tab will appear as shown below.; if your ISP did not assign you a block
Prestige 100WH Quick Start Guide 12 Step 3. The TCP/IP Properties dialog with IP Address tab will appear as shown below. Step 4. Select Obtain an IP address automatically if your ISP did not assign you a block of registered IP addresses (most cases); otherwise, select Specify an IP address and enter...
Page 17 - Select the; On the; tab, highlight any installed gateways and click the; button
Prestige 100WH Quick Start Guide 13 Step 5. Select the WINS Configuration tab, and click Disable WINS Resolution . Step 6. On the Gateway tab, highlight any installed gateways and click the Remove button until there are none listed.
Page 19 - Chapter 4; From the
Prestige 100WH Quick Start Guide 15 Chapter 4 Windows NT Quick Start This chapter shows you the step-by-step instructions to configure your Windows NTworkstations for Internet access. 4.1 TCP/IP Installation You must first install TCP/IP protocol on each Windows NT workstation before you can use itt...
Page 20 - Choose; This will install the TCP/IP protocol on you workstation.
Prestige 100WH Quick Start Guide 16 Step 4. Choose TCP/IP Protocol from the Network Protocol list. Then click OK . This will install the TCP/IP protocol on you workstation.
Page 22 - Select
Prestige 100WH Quick Start Guide 18 Step 4. Select Obtain an IP address automatically if your ISP did not assign you a block of registered IP addresses (most cases). Otherwise, select Specify an IP address and enter the IP address and subnet mask for this workstation from the blockprovided by your I...
Page 25 - Chapter 5; The PWC system consists of three components:; Installing PWC Components; To install the Prestige Web Configurator components:
Prestige 100WH Quick Start Guide 21 Chapter 5 Prestige Web Configurator Setup The Prestige Web Configurator (PWC) is a JAVA-based program that provides a quick,simple, and intuitive way to configure your Prestige. Using a “point-and-click” Web-basedGraphical User Interface (GUI), you can configure, ...
Page 26 - Visual
Prestige 100WH Quick Start Guide 22 Note: The ZyXEL CD Installer Program (Startup.exe) requires the Microsoft ® Visual Basic 5 Runtime libraries. On some systems you may get the message "Error Starting Program" when trying tostart the CD-ROM Installer. If this should occur, use the Windows E...
Page 28 - Starting the Prestige Web Configurator; Prestige Web Configurator.
Prestige 100WH Quick Start Guide 24 5.2 Starting the Prestige Web Configurator Step 1. To start PWC, select Start à Programs à ZyXEL à Prestige Web Configurator. Your web browser will start and show PWC’s welcome page. Step 2. Click the Wizard Setup button at the bottom of the welcome screen to star...
Page 29 - Customer Support; Contacting ZyXEL; ZyXEL Communications Corporation; ZyXEL
Prestige 100WH Quick Start Guide 25 Customer Support ZyXEL Prestige 100WH If you have questions about your ZyXEL products or desire assistance, contact ZyXELCommunications Corporation in one of the following ways. Contacting ZyXEL E-mail Technical Support [email protected] in North America Support@z...