Page 3 - Table of Contents
1 SAFETY NOTICE ................................................................. 2-3 LIST OF MATERIALS ....................................................... 4 INSTALLATION Ducting Calculation Sheet ....................................... 5 Mounting Height & Clearance ............................
Page 4 - Important Safety Notice; READ AND SAVE THESE INSTRUCTIONS
Important Safety Notice READ AND SAVE THESE INSTRUCTIONS 2 WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID-STATE CONTROL DEVICE. WARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: a. Use this unit only in the manne...
Page 5 - CAUTION; WARNING
Important Safety Notice 3 WARNING TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK. NOT FOR USE IN OUTDOOR COOKING ENVIRONMENTS. CAUTION To reduce risk of fire and to properly exhaust air outside - Do not vent exhaust air into spaces within walls, ceilings, attics, crawl spaces or garages. OPERAT...
Page 6 - List of Materials; PARTS NOT SUPPLIED; - Ducting, conduit and all installation tools; HARDWARE PACKAGE CONTENTS BMI; PARTS SUPPLIED; - Hood with internal blower; HARDWARE PACKAGE CONTENTS BVE
List of Materials 4 PARTS NOT SUPPLIED - Ducting, conduit and all installation tools - Cable connector (if required by local codes) - Duct cover extension accessory - Recirculating kit accessory HARDWARE PACKAGE CONTENTS BMI PARTS SUPPLIED MODELS: BMI-E30CG, BMI-E36CG BVE-E30BS, BVE-E36BS 1 - Hood w...
Page 7 - Installation –
5 Duct pieces Total Equivalent number length x used = 3- 1/ 4” x 10” Rect., straight 1 Ft. x ( ) = Ft. 3- 1/ 4” x 10” Rect. to 6” round transition 5 Ft. x ( ) = Ft. 3- 1/ 4” x 10” Rect. to 6” round transition 90 0 elbow 20 Ft. x ( ) = Ft. 6”, 7”, 8”, 10” Round, 90 0 15 Ft. x ( ) = Ft. 6”, 7”, 8”, 10...
Page 8 - DUCTING; Chart A
Installation – Mounting Height & Clearance 6 DUCTING A minimum of 6” round duct must be used to maintain maximum air flow efficiency. Always use rigid type metal ducts only. Flexible ducts could restrict air flow by up to 50%. Use calculation worksheet to compute total duct work (Page 5). ALWAYS...
Page 9 - WARNING FIRE HAZARD; Some Ducting Options; side wall cap
7 WARNING FIRE HAZARD NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages. All exhaust must be ducted to the outside, unless using the recirculating option. Use single wall rigid Metal ductwork only. Fasten all connections with sheet metal scr...
Page 10 - FRONT
8 Installation – BMI Hood Specification 17 1/4 ” 8 15/16 ” 15 7/8 ” 6 7/8 ” 19 3/4 ” 10 5/8 ” 23 15/16 ” 10 3/8 ” 29 15/16 ” or 35 3/16 ” Min. Ducted - 23”Min. Recirc. - 27-1/2”Maximum - 42” FRONT SIDE TOP BACK 8 3/8 ” 3 15/16 ” 1 3/16 ” 6”
Page 12 - A cable locking connector (not supplied) might
10 1. Measure from range top to hood bottom and mark line A. (24” minimum from range top) . 2. Plum and mark center line.3. Mark mounting height line B. (15-7/8” from line A)4. Mark mounting spread from C/L. (8-15/16”) 5. Fasten (2) 6 x 1-1/2” screws into studs on line B but do not tighten all the w...
Page 13 - Mark mounting spread from C/L on line B. From center; WARNING: Electrical wiring must be done by a qualified person(s) in
11 Installation – Mounting the Hood, BVE 1. Measure from range top to hood bottom and mark line A. (24” minimum from range top) . 2. Plum and mark center line.3. Mark mounting height line B. (12-5/16” from line A) 4. Mark mounting spread from C/L on line B. From center line to left mount mark (3-1/2...
Page 14 - RECIRCULATING KIT (REQUIRED IF NO DUCTING IS USED); Charcoal Filter Replacements; Hood Model
12 Ductless recirculation is intended for applications where an exhaust duct work is not possible to be installed. When converted, the hood functions as a recirculating hood rather than an exhaust hood. Fumes and exhaust from cooking are drawn and filtered by a set of optional charcoal filters. The ...
Page 15 - Lights; Touch Controls
13 - On/Off off button will turn power on and off for the entire hood (fan and lights). - The hood will remember the last speed and light level it was last turned off at. - Delay Off Feature: With the fan on, press and hold the On/Off button for three seconds. The fan will change to speed 1 and auto...
Page 16 - Cleaning Stainless Steel; Aluminum Mesh Filters; Removing Aluminum Mesh Filters; Maintenance –
14 SURFACE MAINTENANCE: Do not use corrosive detergents, abrasive detergents or oven cleaners. Do not use any product containing chlorine bleach or any product containing chloride. Do not use steel wool or abrasive scrubbing pads which will scratch and damage surface. Cleaning Stainless Steel Clean ...
Page 17 - LED LIGHT STRIPS; Push the clip
15 LED LIGHT STRIPS In the unlikely event that your LED strip fails, please contact Zephyr to order replacement parts. See list of parts and accessories page for part #’s and contact information. To replace LED light strip 1. Remove aluminum mesh filters. 2. Remove light panel by two screws. 3. Disc...
Page 18 - ACT Conversion; By default the maximum blower CFM is set to 600.; To verify if your installer enabled ACT
16 ACT Conversion AIRFLOW CONTROL TECHNOLOGY (ACT) Some local codes limit the maximum amount of CFM a range hood can move. ACT allows you to control the maximum blower CFM of the range hood without the need for expensive make up air kits. ACT enables the installer to easily set the maximum blower sp...
Page 19 - iring Diagrams
17 Fan: 310W Lamp: LED 5W Total: Max.320W @ 2.66A Voltage 120V 60Hz Power consumption UL file number: E127334 THERMALLY PROTECTED Model:BMI-E30CG BMI-E36CG Fan On/Off Lights W iring Diagrams MAX. 320W @ 2.66A
Page 20 - TROUBLESHOOTING PROCEDURES FOR BRISAS; Issue; Troubleshooting
18 TROUBLESHOOTING PROCEDURES FOR BRISAS Issue Cause What to do After installation, the unit doesn’t work. 1. The power source is not turned ON. 1. Make sure the circuit breaker and the unit’s power is ON. 2. The power line and the cable locking connector is not connecting properly. 2. Check the pow...
Page 21 - Accessories; DESCRIPTION; Replacement Parts
List of Parts & Accessories 19 DESCRIPTION PART# Replacement Parts LED Light Strip (each) Z0B0043 Aluminum Mesh Filter 50200059 (BMI) Aluminum Mesh Filter 50200044 (BVE) Optional Accessories Recirculating Kit BRC-0006 (BMI) Recirculating Kit BRC-0008 (BVE) Replacement Charcoal Filter Z0F-C093 (B...
