Zephyr ALL-E42ABX - Manual

www.zephyronline.com 35-3/8" or 42" Wood Trim Dimensions 1-5/8" Thickness 23-5/8" 13" 11-1/4" Hood Specifi ca tions front of hood side of hood top of hood Models: ADL-M90ASX / ADL-E42ASX - 10 -

www.zephyronline.com Installa tion - In ternal Blo w e r The following instructions are for installing the internal blower. CAUTION: To reduce the risk of fi re and electric shock, install this range- hood only with internal blower models MT-020 provided with the kit cod CBI-600A. For external and i...

Installa tion - In ternal Blo w e r 6. Attach the 6 pin male molex connector from blower wire to the 6 pin female molex con-nector located inside the blower housing. See Fig.6 7. Install the motor and bracket, inside the motor housing, completing the installation using the other screws (6 type B )th...

www.zephyronline.com Installa tion - Ex ternal & In-Line Blo w er P repar a tion The following instructions are for preparing the hood for use with an ex- ternal or in-line blowers models CBE-1000 or PBN-1000A.CAUTION: To reduce the risk of fi re and electric shock, install this rangehood only w...

Installa tion - Ex ternal & In-Line Blo w er P repar a tion Note1 : A cable lock (not included) may be re- quired by local codes. Please review local co-des for more information. 6. Reinstall the cover on the motor housing by following the instructions from step 2 in re-verse order. 7. Attach 6 ...

www.zephyronline.com WARNING FIRE HAZARD NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages. All exhaust must be ducted to the outside, unless using the recirculating op-tion. Use single wall rigid Metal ductwork only. Fasten all connections ...

MOUNTING HEIGHTS The range hood must be installed at a minimum height of 24 inches (61 cm) from the cooking surface. If a connecting duct work composed of two parts is used, the upper part must be placed outside the lower part. Do not connect the range hood duct to the same duct used to exhaust hot ...

5. Position hole template on the ceiling paying at-tention that the arrow is positioned on the same side as the range hood controls. - Make 4, holes in the ceiling and drive in (3 type C) screws without completely tightening them. Pay attention not to insert the screw into the hole marked with an X ...

www.zephyronline.com Installa tion - P o w er Supply C onnec tion GENERAL • Carefully read the following important information regarding installationsafety and maintenance. Keep this information booklet accessible for furtherconsultations. POWER SUPPLY CONNECTION For connection to the power supply r...

Installa tion - P o w er Supply C onnec tion - Connect the electrical conduit to the Field Wiring Compartment using listed onduit fi ttings. - Carry out the power supplly connection in accordance with the national electric code, ANSI/NFPA 70-1999. 5. Replace the lid by following the instructions fro...

www.zephyronline.com Main tencanc e MAINTENANCE • It is recommended to operate the appliance prior to cooking. It is recommended to leave the appliance in operation for 5 minutes after cooking is completed in order to completely eliminate cooking vapors and odors. The proper function of the range ho...

List of P a rts and A cc essories DESCRIPTION HOOD PART# REPLACEMENT PARTS Light Bulb G4, 20W (each) ADL Z0B0013 Light Bulb GU4, 20W (each) ALL Z0B0030 OPTIONAL ACCESSORIES Recirculating Kit ADL, ALL ZRC-00LL Replacement Charcoal Filters ADL, ALL Z0F-00AC Duct Cover Extension, Short (9” ceiling) ADL...