Page 3 - INSTALLATION; able of Contents
1 SAFETY NOTICE ................................................................. 2-3 LIST OF MATERIALS ....................................................... 4 INSTALLATION Ducting Calculation Sheet ....................................... 5 Mounting Height & Clearance ............................
Page 4 - Important Safety Notice; READ AND SAVE THESE INSTRUCTIONS
Important Safety Notice READ AND SAVE THESE INSTRUCTIONS 2 www.zephyronline.com WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID-STATE CONTROL DEVICE. WARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: a. Use this u...
Page 5 - WARNING; CAUTION
Important Safety Notice 3 WARNING TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK. CAUTION To reduce risk of fi re and to properly exhaust air outside - Do not vent exhaust air into spaces within walls, ceilings,attics, crawl spaces or garages. OPERATION Always leave safety grilles and fi lters in...
Page 6 - List of Materials; PARTS SUPPLIED
List of Materials 4 www.zephyronline.com MODELS: AK8000AS AND AK8100AS PARTS SUPPLIED AK8000AS and AK8100AS 1 - Power Pack 1 - Metal mesh fi lter (AK8000AS), 1 - Decorative mesh fi lter (AK8100AS) 2 - Halogen light bulbs (pre-installed) 1 - Single internal blower (pre-installed) 1 - Hardware package H...
Page 8 - DUCTING
Installation – Mounting Height & Clearance 6 www.zephyronline.com DUCTING A minimum of 6” round or 3-1/4” x 10” rectangular duct must be used to maintain maximum air fl ow effi ciency . Always use rigid type metal ducts only. Flexible ducts could restrict air fl ow by up to 50%. Also use calculatio...
Page 9 - WARNING FIRE HAZARD; Some Ducting Options; Installation –; Soffit or crawl space
7 WARNING FIRE HAZARD NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages. All exhaust must be ducted to the outside. Use metal ductwork only. Fasten all connections with sheet metal screws and tape all joints with certifi ed Silver Tape or Duc...
Page 10 - top
8 www.zephyronline.com Installation – Specifi cations top front bottom side 4-1/8” 5-3/8” 3-3/4” 10-5/8” 5-7/8” 1-1/16” 10-1/2” 11-13/16” 26-9/16” 27-9/16” 27-9/16” 25-3/4” 9-3/8” 8-1 1/16” 1 1 -3/16” 1 1 -3/16” 10-5/16” 1-5/16” 15” 18-15/16” 10-5/16” 1-1/8” C/L
Page 12 - FIG 3 and FIG 4
10 www.zephyronline.com Installation – Installing the Power Pack 1. Install optional AK08xxAS Stainless Steel Liner. Review manual included with liner for more details. 2. If no liner is used cut out an opening in the bottom of the cabinet by following the dimensions in FIG 1 . 3. Lift Power Pack in...
Page 13 - Blower On/Off Speed Selection; I; Features & Controls –
11 0 I II I II Blower On/Off Speed Selection 1 Lights Bright/Dim/Off 2 0 I II Features & Controls – Slide Controls BLOWER ON/OFF/SPEED SELECTION 0 is off, I is low speed, II is medium speed and III is high speed. LIGHTS BRIGHT/DIM/OFF 0 is off, I is dim, and II is bright. 1 2
Page 14 - Metal Mesh and Decorative Mesh Filters; Installing Decorative Mesh Filter, FIG 6:
Maintenance – Cleaning and Installing Filters 12 www.zephyronline.com SURFACE MAINTENANCE: Clean periodically with hot soapy water and clean cotton cloth. Do not use corrosive or abrasive detergent, or steel wool/ scoring pads which will scratch and damage surface. Do not use products containing chl...
Page 15 - Maintenance –; of
Maintenance – AK8000AS Recirculating Kit 13 DUCTLESS RECIRCULATING (AK8000AS ONLY): Ductless recirculating is intended for applications where an exhaust duct work is not possible to be installed.When converted, the power pack functions in air “purifying” mode rather than exhausting the air. Fumes an...
Page 16 - REPLACING LIGHT BULBS; CAUTION: Light bulb becomes extremely hot when turned on.; Bottom View
14 www.zephyronline.com REPLACING LIGHT BULBS CAUTION: Light bulb becomes extremely hot when turned on. DO NOT touch bulb until switched off and cooled. Touching hot bulbs could cause serious burns. Make sure all power is turned off and bulbs are not hot. Remove by turning bulb counter clockwise. No...
Page 17 - roubleshooting; TROUBLESHOOTING PROCEDURES FOR TWISTER AND TORNADO 1; Issue
T roubleshooting 15 TROUBLESHOOTING PROCEDURES FOR TWISTER AND TORNADO 1 Issue Cause What to do After installation, the unit doesn’t work. 1. The power source is not turned ON. 1. Make sure the circuit breaker and the unit’s power is ON. 2. The power line and the cable locking connector is not conne...
Page 18 - DESCRIPTION PART #; Replacement Parts; List of Parts and
16 www.zephyronline.com DESCRIPTION PART # Replacement Parts Light Bulb MR16 (GU10) 35W (each) Z0B-0023 Metal Mesh Filter (each) 50200022 Decorative Mesh Filter (each) 50200024 Optional Accessories Liner,30” AK0800AS Liner,36” AK0836AS Recirculating Kit (AK8000AS ONLY) ZRC-0100 To order parts, visit...
Page 19 - STAPLE YOUR RECEIPT HERE; Te n Ye a r L i m i t e d Wa r r a n t y f o r P a r t s :; S o m e s t a t e s o r p r o v i n c e s d o n o t; To O b t a i n S e r v i c e U n d e r L i m i t e d Wa r r a n t y :; L i m i t e d Wa r r a n t y; P r o o f o f t h e o r i g i n a l p u r c h a s e
1-888-880-8368 STAPLE YOUR RECEIPT HERE TO OBTAIN SERVICE UNDER WARRANTY OR FOR ANY SERVICE RELATED QUESTIONS, please call: Z e p h y r C o r p o r a t i o n ( r e f e r r e d t o h e r e i n a s “ w e ” o r “ u s ” ) w a r r a n t s t o t h e o r i g i n a l c o n s u m e r p u r c h a s e r ( r e ...