Zebra RXi4 - Manual
Zebra RXi4 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Control Panel; Figure 2; Figure 2 • Control Panel; PLUS
- Page 3 – CALIBRATE
- Page 4 – Preparing the Printer for Use; To set up the printer, complete these steps:; Select a location for the printer that meets these conditions:; Caution •; Caution •
- Page 5 – Serial port
- Page 6 – Raise the media door.; PRINTER READY; displays when the
- Page 7 – On the control panel, press; PREVIOUS; or
- Page 8 – Press; PRINT; To exit Setup mode, press
- Page 9 – Load Media; Figure 3; Figure 3 • Tear-Off Mode Media Path; Tag Stock
- Page 10 – Other Xi4 Models; Pull out the media supply guide as far as it goes.
- Page 11 – Flip up the media supply guide.; The printhead may be hot and could cause severe burns. Allow the; Open the printhead assembly by rotating the printhead-open lever (
- Page 12 – Slide the outer media guide (
- Page 13 – If your printer includes a media dancer assembly (; Important •; RIBBON OUT
- Page 14 – Align the media with the inner media guide (
- Page 15 – Push down the printhead assembly (
- Page 16 – Load Ribbon; not load ribbon in the printer. Remove used ribbon from the ribbon; Ribbon must be coated on the outside (refer to the
- Page 17 – If...; Yes
- Page 18 – Does your printer have a ribbon dancer assembly?; Without Ribbon Dancer; Thread the ribbon over the media dancer assembly (
- Page 20 – Bring the ribbon leader over the upper ribbon roller (
- Page 22 – Remove Used Ribbon; To remove used ribbon, complete these steps:; Then
© 2010 ZIH Corp. All product names and numbers are Zebra
trademarks, and Zebra and the Zebra logo are registered
trademarks of ZIH Corp. All rights reserved.
P1008806-002
3/8/10
Xi4™/RXi4™ Quick Reference Guide
Use this guide to operate your printer on a daily basis. For more detailed information, refer to
the
User Guide
.
Printer Components
shows the components inside the media compartment of your printer. Depending on
printer model and the installed options, your printer may look slightly different. Familiarize
yourself with these components before continuing with the printer setup procedure.
Figure 1 • Printer Components
1
Platen roller
7
Media supply guide*
2
Control panel
8
Media supply hanger*
3
Printhead assembly
9
Media spindle*
4
Printhead-open lever
A
Used in 110Xi4/R110Xi4 200 dpi and
300 dpi models.
5
Ribbon take-up spindle
B
Used in 110Xi4/R110Xi4 600 dpi models.
6
Ribbon supply spindle
C
Used in all other Xi4 models.
* Determined by printer model. See A, B, or C.
5
6
1
4
3
2
7
8
7
8
9
A
B
C
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Control Panel 2 P1008806-002 Xi4™/RXi4™ Quick Reference Guide 3/8/10 Control Panel The control panel ( Figure 2 ) indicates the printer’s operating status and controls basic printer operation. Figure 2 • Control Panel 1 2 3 4 5 7 12 13 14 11 6 8 10 9 1 Power light On when the printer is on. 2 PAUSE ...
3 Control Panel 3/8/10 Xi4™/RXi4™ Quick Reference Guide P1008806-002 11 CALIBRATE Calibrates the printer for the following: • Media length • Media type (continuous or non-continuous) • Print method (direct thermal or thermal transfer) • Sensor values 12 PAUSE Starts or stops printer operation when p...
Preparing the Printer for Use 4 P1008806-002 Xi4™/RXi4™ Quick Reference Guide 3/8/10 Preparing the Printer for Use After you have familiarized yourself with the printer components, prepare the printer for use. To set up the printer, complete these steps: 1. Select a location for the printer that mee...
