Yamaha EMX5 - User Manual

Yamaha EMX5

Yamaha EMX5 – User Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
Page: / 2
Loading the manual
Page 1

1

General Specifications

0 dBu = 0.775 Vrms, Output impedance of signal generator (Rs) = 150 Ω
All level controls are at their maximum position if not specified.

*1 THD+N is measured with 22 kHz LPF
*2 Noise is measured with A-weighting filter.
*3 Crosstalk is measured with 1 kHz band pass filter.

The contents of this manual apply to the latest specifications as of the publishing date. To obtain the latest manual, access the Yamaha website then download
the manual file.

Output Power

1 kHz THD+N < 10%
(CEA2006)

630 W + 630 W (4 Ω)
460 W + 460 W (8 Ω)

1 kHz THD+N < 1%
(CEA2006)

500 W + 500 W (4 Ω)
370 W + 370 W (8 Ω)

Input to SPEAKERS

Input to STEREO OUT, AUX1 SEND, AUX2 SEND

Frequency Response

Refer to the nominal
output level @ 1 kHz

+1 dB/-3 dB (40 Hz to 20 kHz)

+0.5 dB/-1 dB (20 Hz to 20 kHz)

Total Harmonic
Distortion

*1

(THD+N)

MIC/LINE =
LINE (CH1–4)

0.1% @ 10 W (40 Hz to 20 kHz)
0.05% @ 50 W (1 kHz)

0.03% @ +14 dBu (20 Hz to 20 kHz)
0.007% @ +20 dBu (1 kHz)

Hum & Noise

*2

(20 Hz to 20 kHz)

Equivalent Input Noise

-117 dBu

Residual Output Noise

-70 dBu (40 Hz to 20 kHz, STEREO MASTER
LEVEL: min)

-82 dBu (20 Hz to 20 kHz, STEREO MASTER
LEVEL: min)

Crosstalk (1 kHz)

*3

-85 dB

Input channels

TOTAL: 12 channels

Mono (MIC/LINE): 8, Stereo (LINE): 4

Output channels

SPEAKERS [A, B], AUX1 SEND, AUX2 SEND, STEREO OUT [L, R], REC OUT [L, R]

Bus

Stereo: 1, AUX: 2 (Including FX)

Input Channel
Function

MIC/LINE (CH1–4)

30 dB PAD

Hi-Z (CH4)

Supported

HPF (CH1–3)

80 Hz, -12 dB/oct.

Equalizer (EQ)

HIGH: 10 kHz +15 dB / -15 dB (Shelving)
MID: 2.5 kHz +15 dB / -15 dB (Peaking)
LOW: 100 Hz +15 dB / -15 dB (Shelving)

COMP (CH1–4)

1-knob COMP

Level Meter

2 × 7 points LED meter (-20, -10, -6, 0, +6, +10, PEAK)

Built-in Effect

SPX Algorithm

24 programs

Output Channel Function

Feedback suppressor, Master EQ, Monitor EQ

Phantom Power Voltage

+48 V

FOOT SW

Effect mute on/off

Protection

Load Protection: DC-fault
Amplifier Protection: Over heat protection, Over current protection, Integral power protection
Power Supply Protection: Over heat protection, Over current protection

Power Requirements

AC 100-240 V, 50 Hz/60 Hz

Power Consumption

42 W (Idle) / 210 W (1/8 Power)

Dimensions (W × H × D)

465 mm × 308 mm × 325 mm (18.3" × 12.1" × 12.8")

Net Weight

9.5 kg (20.9 lb)

Included Accessory

AC Power Cord (2.5 m), Owner’s Manual, Technical Specifications

Optional Accessory

Rack-mount brackets: RK-EMX7, Foot switch: FC5

Operating Temperature

0 to +40°C

Analog Input Characteristics

0 dBu = 0.775 Vrms

*1 Sensitivity is the lowest level that will produce an output of +4 dBu (1.228 V) or the nominal output level when the unit is set to maximum gain.

(All level controls are at their maximum position.)

*2 Level controls setting : Channel level controls are at their

t

position. Master level controls are at their maximum position.

*3 1&Sleeve = GND, 2&Tip = HOT, 3&Ring = COLD
*4 Tip = Signal, Sleeve = GND
*5 1 = GND, 2 = HOT, 3 = COLD
*6 Tip = LEFT, Ring = RIGHT, Sleeve = GND

Analog Output Characteristics

0 dBu = 0.775 Vrms
0 dBV = 1.00 Vrms

*1 Tip = HOT, Ring = COLD, Sleeve = GND

Speaker Output Characteristics

*1 1+ = Positive, 1- = Negative
*2 Tip = Positive, Sleeve = Negative

Input Jack

MIC/LINE

Hi-Z

Actual Load

Impedance

For Use

with

Nominal

Input Level

Connector

Sensitivity

*1

Nominal Level
(

t

Position)

*2

Max.

Before Clip

CH 1–4

XLR

MIC

—

3 kΩ

50–600 Ω

Mics

-60 dBu

(0.775 mV)

-43 dBu

(5.48 mV)

-15 dBu

(138 mV)

Combo jack

*3

(Balanced)

LINE

—

-30 dBu

(24.5 mV)

-13 dBu

(173 mV)

+15 dBu

(4.36 V)

Phone

MIC

—

8 kΩ

600 Ω

Lines

-50 dBu

(2.45 mV)

-33 dBu

(17.3 mV)

-5 dBu

(436 mV)

LINE

—

-20 dBu

(77.5 mV)

-3 dBu

(548 mV)

+25 dBu

(13.8 V)

CH 4 (Hi-Z)

Phone

MIC

ON

1 MΩ

10 kΩ

Lines

-50 dBu

(2.45 mV)

-33 dBu

(17.3 mV)

-5 dBu

(436 mV)

Phone jack

*4

(Unbalanced)

LINE

-20 dBu

(77.5 mV)

-3 dBu

(548 mV)

+20 dBu

(7.75 V)

CH 5/6, 7/8

XLR

—

—

3 kΩ

50–600 Ω

Mics

-60 dBu

(0.775 mV)

-43 dBu

(5.48 mV)

-15 dBu

(138 mV)

XLR-3-31

*5

(Balanced)

Phone

10 kΩ

600 Ω Lines

-20 dBu

(77.5 mV)

-3 dBu

(548 mV)

+25 dBu

(13.8 V)

Phone jack

*4

(Unbalanced)

CH 9/10, 11/12

XLR

—

—

3 kΩ

50–600 Ω

Mics

-60 dBu

(0.775 mV)

-43 dBu

(5.48 mV)

-15 dBu

(138 mV)

XLR-3-31

*5

(Balanced)

Pin

10 kΩ

600 Ω Lines

-8 dBu

(316 mV)

+10 dBu

(2.45 V)

+25 dBu

(13.8 V)

RCA pin

(Unbalanced)

CH 11/12

Mini

jack

—

—

10 kΩ

600 Ω Lines

-8 dBu

(316 mV)

+10 dBu

(2.45 V)

+25 dBu

(13.8 V)

Stereo mini jack

*6

(Unbalanced)

Output Jack

Actual Source

Impedance

For Use with Nominal

Output level

Connector

Nominal

Max. Before Clip

STEREO OUT L, R

600 Ω

10 kΩ Lines

+4 dBu

(1.228 V)

+20 dBu

(7.75 V)

Phone jack

*1

(Impedance balanced)

AUX SEND 1, 2

600 Ω

10 kΩ Lines

+4 dBu

(1.228 V)

+20 dBu

(7.75 V)

Phone jack

*1

(Impedance balanced)

REC OUT L, R

600 Ω

10 kΩ Lines

-10 dBV

(0.308 V)

+18 dBV

(7.75 V)

RCA pin

(Unbalanced)

Output Jack

Actual Source

Impedance

For Use with Nominal

Output level

Connector

1 kHz

THD+N < 1%

(CEA2006)

1 kHz

THD+N < 10%

(CEA2006)

SPEAKERS A, B

< 0.1 Ω

4 Ω Speakers

500 W

630 W

Neutrik speakON

®

NL4

*1

Phone jack

*2

8 Ω Speakers

370 W

460 W

ZW11940

Technical Specifications

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Was this manual helpful?

About this manual

Brand
Yamaha
Model
EMX5
Document type
User Manual
Language(s)
English
Pages
2
File size
83.7 KB
Format
PDF

Ask a question

Up to 3 photos. Max 5 MB each. Formats: JPG, JPEG, PNG, WebP.