X10 VK84A - Manual

10 11 Once the camera and receiver are in place, adjust their antennas so that they face each other. The side of the camera’s antenna with the dot on it should face the side of the receiver’s antenna marked with four squares. Adjust the positions to improve the picture on your TV. Basic Camera Setup...

12 13 S ECURE V IDEO C ONNECTION S ETUP If you prefer a secure video connection, you can use a video cable to connect the camera directly to your TV. This setup does not use the wireless video receiver. 1. Turn off the camera’s wireless transmitter: Locate the transmission switch on the bottom of th...

14 15 R EMOTE C ONTROL F EATURES Your SentinelPro Camera includes many versatile and powerful features. This section will show you how to get the most from your camera. Stored Positions Your SentinelPro Camera can remember nine locations, including vertical/horizontal positions, and zoom settings. S...

16 17 Clearing Stored Positions You can delete all stored positions. Here’s how: 1. Press and release C1. 2. Press and hold Setup until the C1 button lights green. 3. Press Center. 4. Press Setup again. Focus Controls In addition to the auto focus feature, you can control the focus of the camera man...

18 19 Camera should be installed into the base of the dome after knocking out the holes, knock out 3 holes for mounting on a ceiling or 1 hole for the wall mounting bracket: Mounting the camera on a ceiling 1. Knock out the three holes on the base of the dome using a screwdriver and hammer. 2. Inser...

22 23 M ULTI -C AMERA S YSTEMS The SentinelPro Camera System is designed so that you can use up to four cameras together. Follow the steps in this section to set up and use your additional cameras. Setting Up Multiple Cameras Each camera comes pre-programmed as camera 1 (C1). The fi rst camera you s...

24 25 Changing the House Code for the Remote The Camera and Remote come set to House Code A by default. To change the House Code on the remote follow steps 1 through 4 below: 1. Press and release the X10 button (red indicator fl ashes). 2. Press and hold Setup until the red indicator lights steadily...

26 27 1. Press C1, C2, C3, or C4 to select the camera you want to control. 3. Press the Right arrow button to bring up the onscreen menu. 2. Press and hold Setup until the camera button light stays on. Press and hold setup again until the camera button stays on again. A DVANCED O NSCREEN M ENU O PTI...

30 31 Color Settings The options in the color settings menu control the appearance of the video picture you get from the camera. · ATW: Adjusts the settings for Auto Trace White Balance (ATW). ATW automatically adjusts the picture to accurately show white in response to varying light conditions. Cha...

38 39 T ROUBLESHOOTING If there’s no camera picture on your TV (wireless connection): 1. Make sure your Wireless Video Receiver is connected to power and turned On. 2. Select the appropriate video input on your TV. Usually you can select the input mode by pressing the VIDEO or INPUT button on the re...

40 41 If there’s no camera picture on your TV (secure connection): 1. Select the appropriate video input on your TV. Usually you can select the input mode by pressing the VIDEO or INPUT button on the remote control. Or you might have to change the TV to Channel 0 or 2, and then use Channel Down to c...

42 43 Controlling X10 Modules Here’s how to control X10 modules with your SentinelPro Remote Control. The remote is set to House Code A by default. 1. Press and release the X10 button. 2. Use the number buttons to enter the Unit Code number of the chosen module. (You can press 1, then 6 for Unit Cod...

FCC Caution THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, I N C L U D I N G I N T E R F E R E N C E T H AT M AY C A U S E U N D E ...