X10 IR32A - Manual

15 14 Setting Up X10 Devices The IR32A IconRemote - coupled with other X10 HomeAutomation Modules - gives you the ability to control every- thing electrical in your home. Once you set up your remote, you can control most any electrical device from the remote, usingthe keys that have been configured ...

19 18 Using The Remote Assuming you followed the steps on the previous pages andhave set up some devices and some favorites, you can now usethe remote. See the sections that follow to set up more devicesand/or favorites, and to set up other functions. (See page 37 tolearn how to set up more favorite...

21 20 Some icons will only provide On or Offfunctions, while some may providedimming. It depends on the device’scapabilities. The example shown to theright has two X10 Home Automationdevices, a camera base (VK74A RoboticMount) and a module that turns anoutside light on and off. Pressing the SideKey ...

25 24 Tips On Learning The following are the guidelines that will help you use thisfeature: a. Some functions from some types of remotes might not be able to be learned. b. No functions may be learned under the HOME, MODE, FAVORITE, HIS, or HERS (hard) keys. c. Use fresh batteries for both the IR32A...

27 26 Learning Main Keys At the Home screen press the Side Keysnext to Setup, More, and then Learn. Then press one of the top four Side KeysK6-K9 to the right of the screen. Select the Device you want to learn keysfor. In this example we only have a TV,Cable Box and Satellite Receiver set up,so the ...

29 28 Before learning the second key in theMacro, you can set a delay (1-10 sec)after which the command stored in theMacro will be sent. For example, yourTV might require a few seconds afterturning it on before it will respond to aChannel Up/Down command.(Repeatedly press the Side Key next toSet Del...

31 30 Next, point the remote you want to learncommands from at the bottom of theIR32A IconRemote, and press OK whenyou’re ready. (See Tips on Learning onpage 25.) Learning Side Keys, cont. Next press the key on the other remotefor the function you want to learn.Hold the key pressed until the screen ...

33 32 A Macro could include the Power key foryour TV, followed by the Power key foryour Cable box, followed (after a 2second delay), by digit 4 from your cableremote. Then, when you later activate thisMacro, it will turn on your TV, turn onyour cable box, wait 2 seconds, and thenset the cable box to...

37 36 Setting up more, cont. Setting up more Favorites When you first inserted the batteries in theremote you likely went through theWizard and set up a few favorites. Youcould only set up 10 favorites at that time.Here’s how to set up more favorites. Pressthe HOME key to display the Home screen. Th...

39 38 Setting up more, cont. Reordering Favorites This lets you move the favorites that youhave previously set up in a group todifferent locations on the screen, i.e.,reorder them. Press the HOME key, select Setup , and then select Favorites . Then, at the screen to the right select Reorder . Pick t...

43 42 Advanced Settings Press these keys using the followingsequence: HOME, Setup , More , and Advanced . The screen to the right lets you change thebacklight delay; enter codes for devicesdirectly from the printed code list thatcame with the remote; set uppunchthrough for various devices; andlimit ...

45 44 Advanced Settings, cont. Here we’ve set the Volume and Mute tooperate the TV; and Chan Up/Down tooperate the Cable Box; - even though theremote is in DVD mode. Play, Stop,Pause, etc., will operate the DVD (i.e.,Punchthrough Not Set for Play, etc.).You need to set up Punchthrough for eachdevice...

49 48 X10 Macros Macros allow you to combine a number of commands,including time delays, using a single key press. There are twoways to create a Macro. The first method using a TM751 that was set uppreviously: • Press the Home Button. • At the screen shown, press the Side Key for X10 Macros and pres...