Winegard RV-7012 - Manual

INSTALLING FC-5910

CONNECTORS ON COAX CABLE

STEP 1:

Strip outer cover back 1/2"* from end of cable. Fray

braid back as far as outer cover will allow.

STEP 2:

Trim braid close to outer cover and remove 1/4"* of

inner insulation

being careful not to nick center conductor

.

Make sure no foil or braid can touch center conductor.

STEP 3:

Slide connector tip between braid and inner insulation

(braid and foil, on foil shield cable) and push connector on cable

as far as it will go. Crimp built-in ferrule with proper crimping

tool.

Hex connector requires hex crimping tool. Do Not

crush

cable out-of-round. * If installing in very hot weather, increase

these dimensions 1/8".

Figure 5

STEP 5.

Mount power supply in wall with

screws provided and attach TV set cable to jack

on front. Connect band separator to VHF and

UHF antenna terminals of TV set, if required.

Press switch on front of outlet and check that

light is on.

OPERATION: To receive cable signals from

outdoor receptacle:

Press

switch to OFF

(CABLE) position. Light on wall plate will go off

showing that power is no longer connected to

the antenna and that both TV sets are receiving

signals from outdoor receptacle.

To receive signals from antenna:

Press

switch to ON (ANT) position. Light on wallplate

will come on showing that power is connected

to the antenna and both TV sets are receiving

signals from the antenna.

NOTE: Make sure the antenna is in the

operating position (up) and pointed at the

station desired.

Figure 4

Antenna

Set 2

Cable

INSTRUCTIONS

RV WALL PLATE/

POWER SUPPLY

MODELS RV-7012, RV-7032, RV-7042

Made in U.S.A.

INSTRUCTIONS

RV WALL PLATE/

POWER SUPPLY

MODELS RV-7012, RV-7032, RV-7042

Made in U.S.A.

INSTRUCTIONS

RV WALL PLATE/

POWER SUPPLY

MODELS RV-7012, RV-7032, RV-7042

Made in U.S.A.

WINEGARD COMPANY

3000 KIRKWOOD ST., BURLINGTON, IA 52601-2000

Printed in U.S.A. 2451486 Rev.2 1/10

This unit is equipped with a polyswitch,

(current limiting device), which will shut down

+12VDC if there is a direct short between

antenna and power supply. Green indicator light

will not light. Once short is eliminated, device will

reset itself in approximately 2 minutes.

DESCRIPTION

Wall plate/power supply to operate Winegard RV

antenna with outdoor receptacle for TV set and

cable input. Wall plate/power supply provides

+12VDC to antenna and +12 volt receptacle

as well as antenna signals to two TV sets.

Cable input from outdoor receptacle connects

to wall plate and may be switched so either

antenna or cable or signals may be watched.

See applications.

NOTE: THIS UNIT IS NOT AN AMPLIFIER. USE ONLY

WITH A WINEGARD AMPLIFIED RV ANTENNA.

WINEGARD COMPANY

3000 KIRKWOOD ST., BURLINGTON, IA 52601-2000

Printed in U.S.A. 2451486 Rev.2 1/10

This unit is equipped with a polyswitch,

(current limiting device), which will shut down

+12VDC if there is a direct short between

antenna and power supply. Green indicator light

will not light. Once short is eliminated, device will

reset itself in approximately 2 minutes.

DESCRIPTION

Wall plate/power supply to operate Winegard

RV antenna with outdoor receptacle for TV

set and cable input. Wall plate/power supply

provides +12VDC to antenna and +12 volt

receptacle as well as antenna signals to two

TV sets. Cable input from outdoor receptacle

connects to wall plate and may be switched so

either antenna or cable signals may be watched.

See applications.

NOTE: THIS UNIT IS NOT AN AMPLIFIER. USE ONLY

WITH A WINEGARD AMPLIFIED RV ANTENNA.

WINEGARD COMPANY

3000 KIRKWOOD ST., BURLINGTON, IA 52601-2000

Printed in U.S.A. 2451486 Rev.2 1/10

This unit is equipped with a polyswitch,

(current limiting device), which will shut down

+12VDC if there is a direct short between

antenna and power supply. Green indicator light

will not light. Once short is eliminated, device will

reset itself in approximately 2 minutes.

DESCRIPTION

Wall plate/power supply to operate Winegard

RV antenna with outdoor receptacle for TV

set and cable input. Wall plate/power supply

provides +12VDC to antenna and +12 volt

receptacle as well as antenna signals to two

TV sets. Cable input from outdoor receptacle

connects to wall plate and may be switched so

either antenna or cable signals may be watched.

See applications.

NOTE: THIS UNIT IS NOT AN AMPLIFIER. USE ONLY

WITH A WINEGARD AMPLIFIED RV ANTENNA.

STEP 5.

Mount power supply in wall with

screws provided and attach TV set cable to jack

on front. Connect band separator to VHF and

UHF antenna terminals of TV set, if required.

Press switch on front of outlet and check that

light is on.

OPERATION: To receive cable signals from

outdoor receptacle:

Press

switch to OFF

(CABLE) position. Light on wall plate will go off

showing that power is no longer connected to

the antenna and that both TV sets are receiving

signals from outdoor receptacle.

To receive signals from antenna:

Press

switch to ON (ANT) position. Light on wallplate

will come on showing that power is connected

to the antenna and both TV sets are receiving

signals from the antenna.

NOTE: Make sure the antenna is in the

operating position (up) and pointed at the

station desired.

Figure 4

Antenna

Set 2

Cable

STEP 5.

Mount power supply in wall with

screws provided and attach TV set cable to jack

on front. Connect band separator to VHF and

UHF antenna terminals of TV set, if required.

Press switch on front of outlet and check that

light is on.

OPERATION: To receive cable signals from

outdoor receptacle:

Press

switch to OFF

(CABLE) position. Light on wall plate will go off

showing that power is no longer connected to

the antenna and that both TV sets are receiving

signals from outdoor receptacle.

To receive signals from antenna:

Press

switch to ON (ANT) position. Light on wallplate

will come on showing that power is connected

to the antenna and both TV sets are receiving

signals from the antenna.

NOTE: Make sure the antenna is in the

operating position (up) and pointed at the

station desired.

Figure 4

Antenna

Set 2

Cable

WINEGARD MOBILE PRODUCTS LIMITED WARRANTY

(2 YEARS PARTS; 1 YEAR LABOR)

Winegard Company warrants this product against defects in

materials or workmanship for a period of two (2) years from the

date of original purchase. During year one (1) of such warranty,

Winegard Company will also pay authorized labor costs to an

authorized Winegard dealer to repair or replace defective

products. No warranty claim will be honored unless at the time

the claim is made, Customer presents proof of purchase to an

authorized Winegard dealer (to locate the nearest authorized

Winegard dealer, contact Winegard Company, 3000 Kirkwood

Street, Burlington, Iowa 52601, Telephone 800-288-8094 or

visit www.winegard.com). Customer must provide proof of

purchase with a dated sales receipt for the Winegard product

to verify the product is under warranty. If the date of purchase

cannot be verified, the warranty period shall be considered to

begin thirty (30) days after the date of manufacture.

If a defect in material or workmanship is discovered, Customer

may take the product to an authorized Winegard dealer for

service. Customer must provide proof of purchase to verify

the product is under warranty. If the product is brought to an

authorized Winegard dealer for service prior to expiration of

year one (1) of the warranty period and a defect in material

or workmanship is verified by Winegard Technical Services,

Winegard Company will cover the Winegard dealer’s labor

charges for warranty service. The Winegard dealer must

contact Winegard Technical Services in advance for pre-

approval of the service. Approval of the service is at the sole

discretion of Winegard Company.

Alternatively, Customer may ship the product prepaid to

Winegard Technical Services (located at 3111 Kirkwood

Street, Burlington, Iowa 52601, Telephone 800-788-

4417). Customer must return the product along with a brief

description of the problem and provide Winegard Technical

Services with Customer’s name, address, and phone number.

Customer must also provide proof of purchase to verify the

product is under warranty. If the product is returned before the

expiration of the warranty period, Winegard Company will (at

its option) either repair or replace the product.

This Limited Warranty does not apply if the product has been

damaged, deteriorates, malfunctions or fails from: improper

installation, misuse, abuse, neglect, accident, tampering,

modification of the product as originally manufactured by

Winegard in any manner whatsoever, removing or defacing

any serial number, usage not in accordance with product

instructions or acts of nature such as damage caused by

wind, lightning, ice or corrosive environments such as salt

spray and acid rain. This Limited Warranty also does not

apply if the product becomes unable to perform its’ intended

function in any way as a result of the television signal provider

making any changes in technology or service.

RETURN AUTHORIZATION POLICY

A Return Material Authorization (RMA) is required prior to

returning any product to Winegard Company or Winegard

Warranty Services under this warranty policy. Please call our

Technical Services Department at 800-788-4417 or send an

e-mail to [email protected] to obtain the RMA number.

Please furnish the date of purchase when requesting an RMA

number. Enclose the product in a prepaid package and

write the RMA number in large, clear letters on the outside

of the package. To avoid confusion or misunderstanding, a

shipment(s) without an RMA number(s) or an unauthorized

return(s) will be refused and returned to Customer freight

collect.

WINEGARD COMPANY DOES NOT ASSUME ANY

LIABILITIES FOR ANY OTHER WARRANTIES, EXPRESS

OR IMPLIED, MADE BY ANY OTHER PERSON.

ALL OTHER WARRANTIES WHETHER EXPRESS, IMPLIED

OR STATUTORY INCLUDING WARRANTIES OF FITNESS

FOR A PARTICULAR PURPOSE AND MERCHANTABILITY

ARE LIMITED TO THE TWO YEAR PERIOD OF THIS

WARRANTY.

In states that do not allow limitations on implied warranties,

or the exclusion of limitation of incidental or consequential

damages, the above limitations or exclusions do not apply.

Some states do not allow limitations on how long an implied

warranty lasts, or the exclusion of limitation of incidental

or consequential damages, so the above limitations or

exclusions may not apply to you.

This warranty gives Customer specific legal rights.

Customer may also have other rights that may vary from

state to state.

SATELLITE RECEIVER WARRANTY

See manufacturer’s limited warranty policy.

WS-MOBWARREREV 2 Rev.1/10

Alternatively, Customer may ship the product prepaid to

Winegard Technical Services (located at 3111 Kirkwood

Street, Burlington, Iowa 52601, Telephone 800-788-

4417). Customer must return the product along with a brief

description of the problem and provide Winegard Technical

Services with Customer’s name, address, and phone number.

Customer must also provide proof of purchase to verify the

product is under warranty. If the product is returned before the

expiration of the warranty period, Winegard Company will (at

its option) either repair or replace the product.

This Limited Warranty does not apply if the product has been

damaged, deteriorates, malfunctions or fails from: improper

installation, misuse, abuse, neglect, accident, tampering,

modification of the product as originally manufactured by

Winegard in any manner whatsoever, removing or defacing

any serial number, usage not in accordance with product

instructions or acts of nature such as damage caused by

wind, lightning, ice or corrosive environments such as salt

spray and acid rain. This Limited Warranty also does not

apply if the product becomes unable to perform its’ intended

function in any way as a result of the television signal provider

making any changes in technology or service.

RETURN AUTHORIZATION POLICY

A Return Material Authorization (RMA) is required prior to

returning any product to Winegard Company or Winegard

Warranty Services under this warranty policy. Please call our

Technical Services Department at 800-788-4417 or send an

e-mail to [email protected] to obtain the RMA number.

Please furnish the date of purchase when requesting an RMA

number. Enclose the product in a prepaid package and

write the RMA number in large, clear letters on the outside

of the package. To avoid confusion or misunderstanding, a

shipment(s) without an RMA number(s) or an unauthorized

return(s) will be refused and returned to Customer freight

collect.

WINEGARD COMPANY DOES NOT ASSUME ANY

LIABILITIES FOR ANY OTHER WARRANTIES, EXPRESS

OR IMPLIED, MADE BY ANY OTHER PERSON.

ALL OTHER WARRANTIES WHETHER EXPRESS, IMPLIED

OR STATUTORY INCLUDING WARRANTIES OF FITNESS

FOR A PARTICULAR PURPOSE AND MERCHANTABILITY

ARE LIMITED TO THE TWO YEAR PERIOD OF THIS

WARRANTY.

In states that do not allow limitations on implied warranties,

or the exclusion of limitation of incidental or consequential

damages, the above limitations or exclusions do not apply.

Some states do not allow limitations on how long an implied

warranty lasts, or the exclusion of limitation of incidental

or consequential damages, so the above limitations or

exclusions may not apply to you.

This warranty gives Customer specific legal rights.

Customer may also have other rights that may vary from

state to state.

SATELLITE RECEIVER WARRANTY

See manufacturer’s limited warranty policy.

WS-MOBWARREREV 2 Rev.1/10

Alternatively, Customer may ship the product prepaid to

Winegard Technical Services (located at 3111 Kirkwood

Street, Burlington, Iowa 52601, Telephone 800-788-

4417). Customer must return the product along with a brief

description of the problem and provide Winegard Technical

Services with Customer’s name, address, and phone number.

Customer must also provide proof of purchase to verify the

product is under warranty. If the product is returned before the

expiration of the warranty period, Winegard Company will (at

its option) either repair or replace the product.

This Limited Warranty does not apply if the product has been

damaged, deteriorates, malfunctions or fails from: improper

installation, misuse, abuse, neglect, accident, tampering,

modification of the product as originally manufactured by

Winegard in any manner whatsoever, removing or defacing

any serial number, usage not in accordance with product

instructions or acts of nature such as damage caused by

wind, lightning, ice or corrosive environments such as salt

spray and acid rain. This Limited Warranty also does not

apply if the product becomes unable to perform its’ intended

function in any way as a result of the television signal provider

making any changes in technology or service.

RETURN AUTHORIZATION POLICY

A Return Material Authorization (RMA) is required prior to

returning any product to Winegard Company or Winegard

Warranty Services under this warranty policy. Please call our

Technical Services Department at 800-788-4417 or send an

e-mail to [email protected] to obtain the RMA number.

Please furnish the date of purchase when requesting an RMA

number. Enclose the product in a prepaid package and

write the RMA number in large, clear letters on the outside

of the package. To avoid confusion or misunderstanding, a

shipment(s) without an RMA number(s) or an unauthorized

return(s) will be refused and returned to Customer freight

collect.

WINEGARD COMPANY DOES NOT ASSUME ANY

LIABILITIES FOR ANY OTHER WARRANTIES, EXPRESS

OR IMPLIED, MADE BY ANY OTHER PERSON.

ALL OTHER WARRANTIES WHETHER EXPRESS, IMPLIED

OR STATUTORY INCLUDING WARRANTIES OF FITNESS

FOR A PARTICULAR PURPOSE AND MERCHANTABILITY

ARE LIMITED TO THE TWO YEAR PERIOD OF THIS

WARRANTY.

In states that do not allow limitations on implied warranties,

or the exclusion of limitation of incidental or consequential

damages, the above limitations or exclusions do not apply.

Some states do not allow limitations on how long an implied

warranty lasts, or the exclusion of limitation of incidental

or consequential damages, so the above limitations or

exclusions may not apply to you.

This warranty gives Customer specific legal rights.

Customer may also have other rights that may vary from

state to state.

SATELLITE RECEIVER WARRANTY

See manufacturer’s limited warranty policy.

WS-MOBWARREREV 2 Rev.1/10

INSTALLING FC-5910

CONNECTORS ON COAX CABLE

STEP 1:

Strip outer cover back 1/2"* from end of cable. Fray

braid back as far as outer cover will allow.

STEP 2:

Trim braid close to outer cover and remove 1/4"* of

inner insulation

being careful not to nick center conductor

.

Make sure no foil or braid can touch center conductor.

STEP 3:

Slide connector tip between braid and inner insulation

(braid and foil, on foil shield cable) and push connector on cable

as far as it will go. Crimp built-in ferrule with proper crimping

tool.

Hex connector requires hex crimping tool. Do Not

crush

cable out-of-round. * If installing in very hot weather, increase

these dimensions 1/8".

Figure 5

WINEGARD MOBILE PRODUCTS LIMITED WARRANTY

(2 YEARS PARTS; 1 YEAR LABOR)

Winegard Company warrants this product against defects in

materials or workmanship for a period of two (2) years from the

date of original purchase. During year one (1) of such warranty,

Winegard Company will also pay authorized labor costs to an

authorized Winegard dealer to repair or replace defective

products. No warranty claim will be honored unless at the time

the claim is made, Customer presents proof of purchase to an

authorized Winegard dealer (to locate the nearest authorized

Winegard dealer, contact Winegard Company, 3000 Kirkwood

Street, Burlington, Iowa 52601, Telephone 800-288-8094 or

visit www.winegard.com). Customer must provide proof of

purchase with a dated sales receipt for the Winegard product

to verify the product is under warranty. If the date of purchase

cannot be verified, the warranty period shall be considered to

begin thirty (30) days after the date of manufacture.

If a defect in material or workmanship is discovered, Customer

may take the product to an authorized Winegard dealer for

service. Customer must provide proof of purchase to verify

the product is under warranty. If the product is brought to an

authorized Winegard dealer for service prior to expiration of

year one (1) of the warranty period and a defect in material

or workmanship is verified by Winegard Technical Services,

Winegard Company will cover the Winegard dealer’s labor

charges for warranty service. The Winegard dealer must

contact Winegard Technical Services in advance for pre-

approval of the service. Approval of the service is at the sole

discretion of Winegard Company.

INSTALLING FC-5910

CONNECTORS ON COAX CABLE

STEP 1:

Strip outer cover back 1/2"* from end of cable. Fray

braid back as far as outer cover will allow.

STEP 2:

Trim braid close to outer cover and remove 1/4"* of

inner insulation

being careful not to nick center conductor

.

Make sure no foil or braid can touch center conductor.

STEP 3:

Slide connector tip between braid and inner insulation

(braid and foil, on foil shield cable) and push connector on cable

as far as it will go. Crimp built-in ferrule with proper crimping

tool.

Hex connector requires hex crimping tool. Do Not

crush

cable out-of-round. * If installing in very hot weather, increase

these dimensions 1/8".

Figure 5

WINEGARD MOBILE PRODUCTS LIMITED WARRANTY

(2 YEARS PARTS; 1 YEAR LABOR)

Winegard Company warrants this product against defects in

materials or workmanship for a period of two (2) years from the

date of original purchase. During year one (1) of such warranty,

Winegard Company will also pay authorized labor costs to an

authorized Winegard dealer to repair or replace defective

products. No warranty claim will be honored unless at the time

the claim is made, Customer presents proof of purchase to an

authorized Winegard dealer (to locate the nearest authorized

Winegard dealer, contact Winegard Company, 3000 Kirkwood

Street, Burlington, Iowa 52601, Telephone 800-288-8094 or

visit www.winegard.com). Customer must provide proof of

purchase with a dated sales receipt for the Winegard product

to verify the product is under warranty. If the date of purchase

cannot be verified, the warranty period shall be considered to

begin thirty (30) days after the date of manufacture.

If a defect in material or workmanship is discovered, Customer

may take the product to an authorized Winegard dealer for

service. Customer must provide proof of purchase to verify

the product is under warranty. If the product is brought to an

authorized Winegard dealer for service prior to expiration of

year one (1) of the warranty period and a defect in material

or workmanship is verified by Winegard Technical Services,

Winegard Company will cover the Winegard dealer’s labor

charges for warranty service. The Winegard dealer must

contact Winegard Technical Services in advance for pre-

approval of the service. Approval of the service is at the sole

discretion of Winegard Company.