Whirlpool WHER25 - Manual

6 Over view and Site Preparation OVERVIEW There are seven easy steps to installing your Drinking Water system. They are as follows: STEP 1 - Install Cold Water Supply fitting STEP 2 - Install Drain Adapter STEP 3 - Install Reverse Osmosis Assembly STEP 4 - Install Storage Tank STEP 5 - Install Rever...

7 Step 1 - Install Supply Water Fitting Questions? Visit www.ecodyne.org or call Toll Free 1-866-986-3223 FIG. 5 Saddle Valve Connection (Included in package) Clamp Z Nut Nut - tightenif necessary Insert Ferrule(Plastic) Use to Connect Tubing Handle Valve Clamp X Seal CHOOSE TYPE OF WATER FITTING TO...

8 Step 2 - Install RO Drain Under Sink FIG. 6 FIG. 7 FIG. 8 INTRODUCTION A suitable drain point is needed for the reject water fromthe Reverse Osmosis Filter. You have two options tochoose from: • Install the Drain Adapter included with your unit See Fig 6, Fig. 7, and Fig. 8. This is used in under ...

9 Step 2 - Install RO Drain In Remote Location FIG. 10 FIG. 9 INSTALL A REMOTE DRAIN POINT AND AIR GAP (Remote Location) You can also run the drain tubing to an existing drain inthe house. A floor drain, laundry tub, standpipe, sump,etc. are suitable drain points. See Fig. 10. This type ofdrain is t...

11 FIG. 12 Step 4 - Install Storage Tank The fitting on the supply tank may need to be tightened7-8 turns to get a good seal. Do not overtighten. INSTALL STORAGE TANK 1. Apply thread sealing tape to the threads on the nipple at the top of the tank. See Fig 12. 2. Locate the tubing connector. See Fig...

12 SELECT LOCATION OF REVERSE OSMOSISFAUCET MOUNTING HOLE You will need to select the location of the ReverseOsmosis Faucet. You have three options to choose from: • Use the existing sink top hole for the spray hose or soap dispenser (Must be 1-3/8” in diameter) • Drill a new hole in the sink • Dril...

14 Cut tubing square with end of tubing round,smooth, with no cuts, nicks or flat spots. Step 6 - Connect Tubes Questions? Visit www.ecodyne.org or call Toll Free 1-866-986-3223 FIG. 20 Tube Correctly Cut Collet Collet (Depress toRemove Tubing) Tubing Fitting O-Ring Seal Collet FIG. 17 HOW TO CUT AN...

15 Step 6 - Connect Tubes CONNECT YELLOW TUBE TO STORAGE TANK 1. Locate the yellow tube. One end is attached to the Reverse Osmosis filter assembly. 2. Run the other end of the yellow tube to the fitting on top of the storage tank. See Fig. 22. 3. Cut tube square and to length. See Fig. 17.4. Do not...

16 Step 7 - Sanitize, Test and Purge System SANITIZE THE SYSTEM Sanitizing is recommended immediately after installa-tion of the Reverse Osmosis system. It’s also recom-mended after servicing inner parts. It is important thatthe person installing or servicing the system haveclean hands while handlin...

18 How Your RO Water System Works HOW YOUR REVERSE OSMOSIS SYSTEMWORKS Introduction: Your Reverse Osmosis (RO) Drinking Water System uses your household water pressure toforce water through three filters. Minerals and impuri-ties are filtered out. Delicious tasting drinking watergoes to the storage ...

19 How Your RO Water System Works FIG. 25 PREFILTER PRODUCT WATER STORAGE RO MEMBRANE checkvalve drain flowcontrol AUTOMATICSHUTOFF WATER IN POSTFILTER PRODUCTWATER FAUCET air gap gravity drain RED YELLOW BLUE GREEN PRODUCT WATER BLA CK WASTE WATER Water Flow Description 1. Water enters prefilter. S...

20 Maintenance PREFILTER/POSTFILTER MAINTENANCE NOTE: It is recommended to replace the battery,prefilter and postfilter cartridges at least every 6months of product water use. Replace more often ifthey begin to plug with sediments. The prefilter and postfilter are replaceable sedimentcartridges with...

21 Maintenance FIG. 27 FLOW CONTROL The flow control is vital for proper operation of theReverse Osmosis membrane cartridge. See Fig. 27. Theflow control, located in the red tube at the system hous-ing, keeps water flowing through the membrane at therequired rate. This is to ensure the system produc...

22 Specifications Supply water pressure limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40-100 psi (280-689 kPa)Supply water temperature limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40-100 ...

23 Warranty ONE YEAR LIMITED WARRANTY ON REVERSE OSMOSIS DRINKING WATER SYSTEM (Except filter cartridges and R. O. membrane) Warrantor: Ecodyne Water Systems Inc., 1890 Woodlane Drive, Woodbury, MN 55125 Warrantor guarantees, to the original owner, that the Reverse Osmosis Drinking Water System, whe...

24 Troubleshooting Questions? Visit www.ecodyne.org or call Toll Free 1-866-986-3223 Problem: Chlorine taste and/or odor in the RO product water. Cause: The level of chlorine in your water supplyexceeds maximum limits, and hasdestroyed the Reverse Osmosis mem-brane. Correction: If the water supply c...

26 Exploded View Questions? Visit www.ecodyne.org or call Toll Free 1-866-986-3223

27 Par ts List Questions? Visit www.ecodyne.org or call Toll Free 1-866-986-3223 Key No. Part No. Description 1 9006062 Screw (2 req’d) 2 9041700 Hanger Washer (2 req’d) 3 7115432 O-ring (2 req’d) 4 7272658 Check Valve 5 7273337 Screw (6 req’d) 6 7281330 Washer (4 req’d) 7 7273345 Automatic Shut-off...