Wells 9010 - Manual

INSTALLATION INSTRUCTIONS READ THIS CAREFULLY BEFORE STARTING THE INSTALLATION Unpack the unit. Inspect all components for completeness and condition. Ensure that all packing materials have been removed from the unit. Verify that the Spray Head Gasket and Spray Disk are properly installed. LEVELING ...

INSTALLATION INSTRUCTIONS (continued) NOTE: This equipment must be installed to comply with applicable federal, state and local plumbing codes and ordinances. WARNING: SHOCK HAZARD Brewer must be properly grounded to prevent possible shock hazard. DO NOT assume a plumbing line will provide such a gr...

OPERATION Fig. 4 Brewer Operation Diagram A. START-UP For initial start-up, or if the brewer has not been used for an extended period of time: ♦ Be sure spray disk and brew gasket are properly installed in the brew head. ♦ Be sure the water supply is properly connected and the water supply valve is ...

OPERATION (continued) WATER HEATER Water temperature is sensed by a thermobulb inserted into the water tank. This temperature signal is fed to the thermostat, which controls line power to the heating element. The setpoint temperature is adjustable at the thermostat. The element is protected from ove...

BREWING COFFEE CAUTION: BURN HAZARD Exposed surfaces of the brewer, brew chamber and decanter may be HOT to the touch, and can cause serious burns. CAUTION: BURN HAZARD To avoid splashing or over-flowing hot liquids, ALWAYS place an empty decanter under the brew chamber before starting the brew cycl...

CLEANING INSTRUCTIONS PROCEDURE: Clean Coffee Brewer PRECAUTIONS: Disconnect brewer from electric power. Allow brewer to cool. FREQUENCY: Daily TOOLS: Mild Detergent, Clean Soft Cloth or Sponge Bristle Brush. 1. Disconnect brewer from electric power. Allow brewer to cool before cleaning. 2. Remove a...

SERVICING INSTRUCTIONS ACCESS PANELS Each warmer plate has a center stud which screws into a bracket. Warmer plates on Canadian brewers are secured with a nut. Remove button plug on bottom of brewer to access nut on main warmer. Remove top panel to access nuts on top warmers. Remove warmer plates by...

SERVICING INSTRUCTIONS (continued) TEMPERATURE ADJUSTMENT Unplug power cord or turn circuit breaker OFF. Remove top panel. Pull vent tube out of tank lid and insert a thermometer of known accuracy in vent hole. Reconnect brewer to electrical power. Place an empty decanter under brew chamber. Energiz...

SERVICING INSTRUCTIONS (continued) 13 601 75815 Owner s M anual In tegri ty Decante r B rewers IMPORTANT: Water pressure must be between 20 p.s.i and 90 p.s.i. flowing pressure. If water pressure exceeds this value, or if water pressure varies greatly, a pressure regulator must be installed in the w...

SERVICING INSTRUCTIONS (continued) 15 IMPORTANT: When replacing water faucet coil, also replace seal gaskets. NOTE: Any abrasion or roughness on the flat end of the seat cup will require replacing the seat cup: Work the seat cup out of the bonnet and off of the end of the stem. Install a new seat cu...

CAUTION: CHEMICAL BURN HAZARD Deliming chemicals may be caustic. Wear appropriate protective gloves and goggles during this procedure. Never siphon deliming chemicals or solutions by mouth. This operation should only be performed by qualified and experienced service personnel. IMPORTANT: DO NOT spil...

EXPLODED VIEW & PARTS LIST (continued) 19 601 75815 Owner s M anual In tegri ty Decante r B rewers 33 34 25 24 34a 19 43 26 28 11 27 29 60 8 10 12 45 9 29a 29b 29c 29d 29e 29f 29g 29h 29j 29k TANK ASSY see PAGE 18 61 59 18 CABINET PLUMBING COMPONENTS ITEM PART NO. DESCRIPTION USED ON 8 8540-3 FO...

EXPLODED VIEW & PARTS LIST (continued) 20 601 75815 Owner s M anual In tegri ty Decante r B rewers ELECTRICAL COMPONENTS ITEM PART NO. DESCRIPTION USED ON 2 8572-18 8533-32 HEATING ELEMENT, WARMER 120V 100W HEATING ELEMENT, WARMER 220V 85W / 240V 100W ALL EXCEPT 9016(EX) 9016(EX) 30 6710-23 8563...

EXPLODED VIEW & PARTS LIST (continued) CABINET COMPONENTS 21 601 75815 Owner s M anual In tegri ty Decante r B rewers ITEM PART NO. DESCRIPTION USED ON 3 8700-16 COVER PLATE, WARMER BLACK 9010, 9012(CA), 9016(EX) 33 8543-42 GASKET, SPRAY HEAD 9010, 9012(CA), 9016(EX) 34 82727 SPRAY DISK, EMBOSSE...

WIRING DIAGRAMS 22 601 75815 Owner s M anual In tegri ty Decante r B rewers 1 2 3 1 2 3 1 2 3 READY LIGHT BREW SWITCH WARMER SWITCH WARMER SWITCH WARMER SWITCH SOLENOID THERMOSTAT TIMER HI-LIMIT BLACK BLACK ORANGE ORANGE BLACK BLACK BLACK BLACK RED GREEN WHITE WHITE WHITE WHITE WHITE WHITE WHITE WHI...

Genuine Parts Protect - YOU - All - Ways SERVICE TRAINING - QUALITY SERVICE SERVICE TRAINING - QUALITY SERVICE CUSTOMER SATISFACTION CUSTOMER SATISFACTION Wells Bloomfield proudly supports CFESA Commercial Food Equipment Service Association Commercial Food Equipment Service Association PRINTED IN UN...