Page 2 - xi
NOTE: For your protection, please note that equipment in this shipment was carefully inspected and packaged by skilled personnel before leaving the factory. Upon acceptance of this shipment, the transportation company assumes full responsibility for its safe delivery. IF SHIPMENT ARRIVES DAMAGED: 1....
Page 4 - FEATURES AND OPERATING CONTROLS
FEATURES AND OPERATING CONTROLS Fig. 1 Features & Operating Controls 2 6 22 75854 Ow ners Ma nual Gourm e t 1000 Air p o t/T herm a l
Page 5 - Installation; AGENCY LISTING INFORMATION
PRECAUTIONS AND GENERAL INFORMATION WARNING: Electric Shock Hazard All servicing requiring access to non-insulated components must be performed by qualified service personnel. Do not open any access panels which require the use of tools. Failure to heed this warning can result in electrical shock. W...
Page 6 - INSTALLATION INSTRUCTIONS; READ THIS CAREFULLY BEFORE STARTING THE INSTALLATION; WATER; line. Flush water line before connecting to Brewer.; Equipment; Water supply inlet line
INSTALLATION INSTRUCTIONS READ THIS CAREFULLY BEFORE STARTING THE INSTALLATION REFER TO EXPLODED VIEWS PAGES 18 thru 21 FOR COMPONENT NAMES/NUMBERS Unpack the unit. Inspect all components for completeness and condition. Ensure that all packing materials have been removed from the unit. Verify that t...
Page 7 - Fig. 2 Water Supply Installation
INSTALLATION INSTRUCTIONS (continued) NOTE: This equipment must be installed to comply with all applicable federal, state and local plumbing codes and ordinances. WARNING ELECTRIC SHOCK HAZARD: Brewer must be properly grounded to prevent possible shock hazard. DO NOT assume a plumbing line will prov...
Page 8 - OPERATION; plugging the brewer into a receptacle, or otherwise
OPERATION Fig. 4 Brewer Operation Diagram A. START-UP For initial start-up, or if the brewer has not been used for an extended period of time: Be sure spray disk and brew gasket are properly installed in the brew head. For automatic brewers, be sure the water supply is properly connected and the wat...
Page 9 - AUTOMATIC OPERATION; OPEN
OPERATION (continued) WATER HEATER Water temperature is sensed by a thermobulb inserted into the water tank. This temperature signal is fed to the thermostat, which controls line power to the heating element. The setpoint temperature is adjustable at the thermostat. The element is protected from ove...
Page 10 - BREWING COFFEE; Any Gourmet 1000TM can be used in the pour-over mode.; C. AUTOMATIC OPERATION; EMPTY
BREWING COFFEE CAUTION: Burn Hazard Exposed surfaces of the brewer, brew chamber and airpot or server may be HOT to the touch, and can cause serious burns. CAUTION: Burn Hazard To avoid splashing or overflowing hot liquids, ALWAYS place an empty airpot or server under the brew chamber before startin...
Page 11 - CLEANING INSTRUCTIONS; PROCEDURE: Clean Coffee Brewer; Remove airpot or thermal server.
CLEANING INSTRUCTIONS PROCEDURE: Clean Coffee Brewer PRECAUTIONS: Disconnect brewer from electric power. Allow brewer to cool. FREQUENCY: Daily TOOLS: Mild Detergent, Clean Soft Cloth or Sponge Bristle Brush, Bottle Brush 1. Disconnect brewer from electric power. Allow brewer to cool before cleaning...
Page 13 - SERVICING INSTRUCTIONS; Fig. 9 Access Panels; TIMER; SOLENOID
SERVICING INSTRUCTIONS ACCESS PANELS TOP PANEL: Remove top panel to access hot water tank, thermostat, heating elements, brew circuit tubing, faucet valve and piping. Top panel is held by two screws at the rear and a retaining lip at the front. FRONT PANEL: Remove front panel to access timer, termin...
Page 14 - TEMPERATURE ADJUSTMENT; Fig. 10 Checking and Adjusting Brew Temperature
SERVICING INSTRUCTIONS (continued) TEMPERATURE ADJUSTMENT Unplug power cord or turn circuit breaker OFF. Remove top panel. Pull vent tube out of tank lid and insert a thermometer of known accuracy in vent hole. Reconnect brewer to electrical power. Place an empty container under brew chamber. Energi...
Page 15 - TIMER ADJUSTMENT (AUTOMATIC BREWERS ONLY); REPLACE THERMOSTAT; OFF; REPLACE HEATING ELEMENT
SERVICING INSTRUCTIONS (continued) IMPORTANT: Water pressure must be between 20 p.s.i and 90 p.s.i. flowing pressure. If water pressure exceeds this value, or if water pressure varies greatly, a pressure regulator must be installed in the water supply line. IMPORTANT: Before setting assembly into ta...
Page 16 - REPLACE SOLENOID
SERVICING INSTRUCTIONS (continued) 14 REPLACE SOLENOID Symptom: Automatic brewer will not flow water; or, automatic brewer drips continuously from brew head. Unplug power cord or turn circuit breaker OFF . Turn OFF and disconnect water supply from brewer inlet fitting. Unscrew water inlet fitting fr...
Page 17 - REPLACE TIMER ASSEMBLY; Unplug power cord or turn circuit breaker OFF.; REPLACE HOT WATER FAUCET COIL
SERVICING INSTRUCTIONS (continued) 15 IMPORTANT: When replacing water faucet coil, also replace seal gaskets. NOTE: Any abrasion or roughness on the flat end of the seat cup will require replacing the seat cup: Work the seat cup out of the bonnet and off of the end of the stem. Install a new seat cu...
Page 18 - PROCEDURE: Delime the Water Tank
CAUTION - CHEMICAL BURN HAZARD Deliming chemicals are caustic. Wear appropriate protective gloves and goggles during this procedure. Never siphon deliming chemicals or solutions by mouth. This operation should only be performed by qualified and ex-perienced service personnel. IMPORTANT: DO NOT spill...
Page 21 - ELECTRICAL COMPONENTS
ELECTRICAL COMPONENTS ITEM PART NO. DESCRIPTION USED ON 31 8707-55 Brew Switch, Momentary Rocker 8780, 8782, 8786, 8788 32 8718-31 Ready-To-Brew Light, green All 35 8718-1 Timer All 36 6407-15 Cord & Cap Assembly All, except 8786 & 8788 36t 8552-18 Terminal Strip 8786, 8788 37 35-210 Strain ...
Page 22 - INTERNAL PLUMBING COMPONENTS
EXPLODED VIEW & PARTS LIST (continued) INTERNAL PLUMBING COMPONENTS ITEM PART NO. DESCRIPTION USED ON 8 8540-3 Faucet Outlet Tube Assembly 8780, 8782, 8786, 8788 9 8540-4 Formed Inlet Tube Assembly 8780, 8782, 8786, 8788 10 8551-30 1/4“ Male Flare x 1/8” FPT 8780, 8782, 8786, 8788 11 8514-26 Nee...
Page 23 - CABINET COMPONENTS
EXPLODED VIEW & PARTS LIST (continued) CABINET COMPONENTS ITEM PART NO. DESCRIPTION USED ON 21 63201 Spacer, .171 ID x .375 LG 8782XL, 8785XL 22 87192 Positioning Bracket 8782XL, 8785XL 33 8543-42 Spray Head Gasket All 34 82727 Spray Disk All 34a 8543-45 Spray Head Retainer All 70 8706-75 Button...
Page 24 - WIRING DIAGRAM
WIRING DIAGRAM 22 6 22 75854 Ow ners Ma nual Gourm e t 1000 Air p o t/T herm a l
Page 26 - for
Bloomfield Industries, Inc. Division of Carrier Commercial Refrigeration In US and Canada Telephone: 775-689-5700 Fax: 888-492-2783 Fax: 800-356-5142 ( ) website: www.wellsbloomfield.com for orders only Bloomfield Industries proudly supports CFESA Commercial Food Equipment Service Association PRINTE...
