Wells 2030 - Manual - manualsarea.com

Page 2 - xi

NOTE: For your protection, please note that equipment in this shipment was carefully inspected and packaged by skilled personnel before leaving the factory. Upon acceptance of this shipment, the transportation company assumes full responsibility for its safe delivery. IF SHIPMENT ARRIVES DAMAGED: 1....

Page 3 - ELECTRICAL SPECIFICATIONS

TABLE OF CONTENTS SPECIFICATIONS Thank You for purchasing this Bloomfield Industries appliance. Proper installation, professional operation and consistent maintenance of this appliance will ensure that it gives you the very best performance and a long, economical service life. This manual contains t...

Page 4 - FEATURES AND OPERATING CONTROLS; Features & Operating Controls

FEATURES AND OPERATING CONTROLS 2 Features & Operating Controls

Page 5 - DO NOT plug in or; PRECAUTIONS AND GENERAL INFORMATION

WARNING: Electric Shock Hazard All servicing requiring access to non-insulated components must be performed by qualified service personnel. Do not open any access panels which require the use of tools. Failure to heed this warning can result in electrical shock. WARNING: Injury Hazard All installati...

Page 6 - INSTALLATION INSTRUCTIONS; READ THIS CAREFULLY BEFORE STARTING THE INSTALLATION; UNPACKING & INITIAL INSPECTION; Brewer should be connected to a; WATER; line. Flush water line before connecting to brewer.; Equipment; Water supply inlet line

INSTALLATION INSTRUCTIONS READ THIS CAREFULLY BEFORE STARTING THE INSTALLATION UNPACKING & INITIAL INSPECTION 1. Unpack the unit. Inspect all components for completeness and condition. Ensure that all packing materials have been removed from the unit. 2. Verify that the Spray Head and Spray Head...

Page 7 - water hammer; in the incoming line, between the backflow; ELECTRICIAN’S INSTALLATION INSTRUCTIONS; listed under UL file E9253.; AGENCY LISTING INFORMATION

INSTALLATION INSTRUCTIONS (continued) NOTE: This equipment must be installed to comply with applicable federal, state and local plumbing codes and ordinances. WARNING ELECTRIC SHOCK HAZARD: Brewer must be properly grounded to prevent possible shock hazard. DO NOT assume a plumbing line will provide ...

Page 8 - OPERATION; Energizing the Brewer:; OPERATING INSTRUCTIONS

OPERATION IMPORTANT: All E-Max T™ brewers are tested and set at the factory. If programming adjust-ments are necessary, refer to the E-Max™ Programming Manual (p/n 73674). To over-ride the Brew Wait mode , press and hold the BREW key for 3 seconds when the brewer is in Brew Wait mode (i.e. when brew...

Page 9 - USER’S GUIDE; Brew complete

OPERATION (continued) WARNING: Burn Hazard. This appliance dispenses very hot liquid. Serious bodily injury from scalding can occur from contact with dispensed liquids. CAUTION: Burn Hazard To avoid splashing or overflowing hot liquids, ALWAYS use an empty dispenser before starting the brew cycle. F...

Page 10 - PROGRAMMING FEATURES AND OPTIONS; E-MaxTM Programming Manual

PROGRAMMING FEATURES AND OPTIONS 1. View Water Temperature in Tank: To view the water temperature on the screen, E-Max T™ brewer must be ON, and not brewing or in the filling mode. Press and hold the 4th key, and depress the 6th key. The actual water temperature will be displayed for 3 seconds. 2. D...

Page 11 - Countdown Quality TimerTM:

8. Clock A. Time – Battery Backup. The E-Max T™ has a battery backup system which will maintain the proper time during power failures, or when the brewer is unplugged (even for very prolonged periods of time). Normally there will not be a need to set the time except for Daylight Saving Time changes,...

Page 14 - FUNCTION; The solenoid has an internal strainer. To clean the; SERVICING INSTRUCTIONS — PLUMBING

FUNCTION 1. Water enters at the inlet fitting of the fill solenoid (32). The solenoid admits water via a command from the controller. NOTE: The solenoid has an internal strainer. To clean the strainer: Shut off water supply. Unscrew the plastic cap protruding from the rear of the brewer. Remove the ...

Page 15 - SERVICING INSTRUCTIONS — PLUMBING (continued); ITEM

SERVICING INSTRUCTIONS — PLUMBING (continued) 13 ITEM DESCRIPTION PART N0. USED ON 1 2 ASSEMBLY, WATER TANK (120V) 83500 2030 6 GASKET, TANK LID 83499 2030 9 TANK LID 83504 2030 10 RETAINING CLIP, TANK LID 83506 2030 11 HOSE, VENT (SILICONE 4.5” LONG) 86014 2030 12 HOSE, FAUCET SUPPLY (SILICONE, 10”...

Page 16 - SERVICING INSTRUCTIONS - ELECTRICAL; ON

SERVICING INSTRUCTIONS - ELECTRICAL FUNCTION 1. Pressing the POWER key energizes the unit. The POWER LED will glow whenever the unit is ON . 2. Automatic fill is accomplished via the "FILL" section of the INLET SOLENOID (32) and a WATER LEVEL PROBE (7). The probe senses ground through the wa...

Page 18 - SERVICING INSTRUCTIONS — DE-LIMING HEATER TANK; Disconnect brewer form the electrical supply. Turn off

SERVICING INSTRUCTIONS — DE-LIMING HEATER TANK 1. Disconnect brewer form the electrical supply. Turn off the water supply and disconnect water supply from the brewer inlet fitting. 2. Remove the top panel to gain access to internal components. 3. Disconnect water level sensor and water temperature s...

Page 19 - TROUBLESHOOTING SUGGESTIONS; Using the CANCEL button will not

TROUBLESHOOTING SUGGESTIONS If the E-Max T™ goes into the error mode as outlined below, it will likely be necessary to reset the brewer in order to test individual components. Note the reset procedure below: • For the first four error modes, press and hold CANCEL for 3 seconds, or RE-ENERGIZE the br...

Page 20 - E-Max TTM TEST PROGRAM; B. Check Data Revision; Time is preset

E-Max T™ TEST PROGRAM 18 Instructions for testing procedures for the following system components (using the E-Max T™ Built-In Diagnostic): Electronic Board Software (Firmware) Revision Keypad switches LED’s Inlet valve, Dump (Brew) valve, By Pass Valve Water level probe, Temperature probe A. Enterin...

Page 22 - EXPLODED VIEW & PARTS LIST

Page 25 - NOTES

Page 26 - Division of Carrier Commercial Refrigeration; for

PRINTED IN UNITED STATES OF AMERICA Bloomfield Industries, Inc. Division of Carrier Commercial Refrigeration In US and Canada Telephone: 775-689-5700 Fax: 888-492-2783 Fax: 800-356-5142 ( ) website: www.wellsbloomfield.com for orders only Bloomfield Industries proudly supports CFESA Commercial Food ...

Wells 2030 - Manual

Table of Contents:

Summary

Other Wells Models