Weider WESY92190 - Manual

5 Note: This introduction will save you moretime than it takes to read it! Identifying Parts To help you identify the small parts used in assem-bly, we have included a PART IDENTIFICATIONCHART located in the center of this manual. Placethe chart on the floor and use it to quickly identify dif-ferent...

6 1. Before beginning assembly, make sure you haveread and understood the information on page 5. Open the parts bag labeled ÒFRAME ASSEMBLY.Ó Press a 2Ó Square Outer Cap (51) onto each end ofthe Stabilizer (5). Insert two 5/16Ó x 2 3/4Ó Carriage Bolts (14) upthrough the Stabilizer (5) and place it f...

8 10. Press a 1 1/2Ó Square Inner Cap (33) into the end of the Seat Frame (36). Insert two 5/16Ó x 2 3/4Ó Bolts (67) through theSupport Plate (27) and the indicated holes in theFront Upright (42). Place the mounting bracket on theSeat Frame (36) over the two Bolts. Tighten a 5/16ÓNylon Locknut (53) ...

Cable Assembly 15. Open the parts bag labeled ÒCABLE ASSEMBLYAND PULLEYS.Ó For Cable identification and rout-ing during steps 15Ð30, refer to the CableDiagram and Cable ID Chart on page 19. Identify the High Cable (2). It is approximately 1631/2Ó long. It is the shortest cable and it has a ball onea...

31. Open the parts bag labeled ÒSEAT ASSEMBLY.Ó Attach the Backrest (41) to the Front Upright (42) withtwo 1/4Ó x 2 1/2Ó Screws (43) and two 1/4Ó FlatWashers (90). Seat Assembly 41 43 43 90 42 30. Wrap the Low Cable (9) around a 3 1/2Ó Pulley (35) in the direction shown. Attach the Pulley to the Fro...

19 Cable Diagram The Cable Diagram below shows the proper routing of the High Cable (2) and the Low Cable (9). The numbersshow the correct route for each Cable. Make sure that the Cables are routed correctly, that the Pulleys move smoothly, and that the Cable Traps do not touch or bind the Cables. I...

20 How to Use the Weight System PLUGGING IN THE POWER CORD Plug in the power cord to a 120-volt outlet. Keep thepower cord away from walkways and heated surfaces.Turn on the power when using the weight system, orthe weight system could be damaged. When you arefinished using the weight system, always...

22 31 63 66 35 Additional slack can be removed by using the PulleyPlates (31). The Pulley Plates have several sets of adjust-ment holes. By moving one or both pulleys to a differentset of holes, the cables will be tightened. To move a Pulley, remove the 3/8Ó Nylon Jamnut (63) andthe 3/8Ó x 1 1/2Ó Bo...

5/16" Nylon Jamnut (91) 3/8" Flat Washer (55) 5/16" Flat Washer (56) 3/8" Nylon Locknut (57) 3/8" Nylon Jamnut (63) 3/8" Plain Nut (85) 1/4" x 2" Bolt (71) 1/4" x 2 1/2" Screw (43) 1/4" x 2" Carriage Bolt (38) 5/16" x 1 3/4" Bolt (58) 5/16"...

Note: Ò#Ó indicates a non-illustrated part. Specifications are subject to change without notice. Part ListÑModel No. WESY92190 R1299A Key No. Qty. Description Key No. Qty. Description 1 1 Top Frame 2 1 High Cable 3 2 1Ó Round Cover Cap 4 4 1Ó Retainer 5 1 Stabilizer 6 4 ÒVÓ-Pulley 7 2 Plastic Bushin...

34 34 30 30 44 33 28 30 34 28 30 34 22 71 38 17 37 13 91 33 29 36 74 73 75 45 45 21 21 3 4 4 3 15 6 57 15 48 47 9 11 58 56 53 53 18 5 51 51 14 52 8 53 1 21 21 67 56 65 50 6 63 35 55 54 2 90 43 41 42 24 10 17 72 67 27 66 35 55 66 66 35 35 55 53 69 50 6 55 21 40 53 21 21 49 77 77 49 46 46 68 43 93 55 ...

Ordering Replacement Parts To order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Mondaythrough Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be pre-pared to give the following information: 1. The MODEL NUM...