Wayne DSP60 - Manual

REMINDER: Keep your dated proof of purchase for warranty purposes! Attach it to this manual or file it for safekeeping.

Please read and save these instructions. Read carefully before
attempting to assemble, install, operate or maintain the product
described. Protect yourself and others by observing all safety
information. Failure to comply with instructions could result in
personal injury and/or property damage! Retain instructions for
future reference.

Description

A sewage pump is intended for use in
domestic sewage lift stations. It is suitable
for pumping sewage, effluent, wastewater,
groundwater, and other nonexplosive,
noncorrosive liquids with up to 2 inch solids.

An acceptable
motor control

device must be provided at time of
installation.

Unpacking

Inspect this unit before it is used.
Occasionally, products are damaged during
shipment. If the pump or components are
damaged, return the unit to the place of
purchase for replacement. Failure to do so
could result in serious injury or death.

Safety Guidelines

This manual contains information that is
very important to know and understand.
This information is provided for SAFETY and
to PREVENT EQUIPMENT PROBLEMS. To help
recognize this information, observe the
following symbols.

Danger indicates

an imminently

hazardous situation which, if not avoided,
will result in death or serious injury.

Warning indicates

a potentially

hazardous situation which, if not avoided,
could result in death or serious injury.

Operating Instructions and Parts Manual

Models DSP60 and DSP75

330600-001 6/03

Caution indicates a

potentially

hazardous situation which, if not
avoided, MAY result in minor or
moderate injury.

Notice indicates

important

information, that if not followed, may
cause damage to equipment.

General Safety Information

1. Know the pump application, limitations,

and po ten tial hazards.

Do not use to pump
flammable or explosive
fluids such as gasoline, fuel
oil, kerosene, etc. Do not
use in flammable and/or explosive
atmospheres. Use pump only with
liquids compatible with pump
component materials. Failure to follow
this warning can result in personal
injury and/or property damage.

2. Make certain that the power source

(electric motor) conforms to the
requirements of the equipment.

Disconnect power before
servicing. If the power dis -
con nect is out of sight, lock
in the open po si tion and
tag it to prevent unexpected

application of power. Failure to do so
could result in fatal electrical shock!

3. Release all pressure within the system

before ser vic ing any component.

4. Drain all liquids from the system before

servicing.

5. Secure the discharge line before starting

the pump. An unsecured discharge line
will whip, possibly causing personal
injury and/or property damage.

6. Check hoses for weak and worn

condition before each use, making
certain that all connections are secure.

7. Periodically inspect the pump and

system com po nents. Perform routine
maintenance as required (See
Maintenance Section).

8. Provide a means of pressure relief for

pumps whose discharge line can be shut-
off or obstructed.

9. Personal Safety:

a. Wear safety glasses at all times when

working with pumps.

b. Keep work area clean, uncluttered

and properly lighted; replace all
unused tools and equipment.

c. Keep visitors a safe distance from the

work area. Make workshop child-
proof with pad locks, master switch es,
and by re mov ing starter keys.

10. When wiring an elec tri cal ly driven pump

such as this, fol low all electrical and safety
codes, as well as the most recent National
Electrical Code (NEC) and the Oc cu pa tion -
al Safety and Health Act (OSHA).

© 2003 Wayne Water Systems

Specifications

Power supply requirements.............120V, 60 hz

Circuit requirements ........................15 amps (min)

Motor duty .......................................Intermittent

Motor ................................................120V, 1 Phase

Horsepower .....................................6/10 (DSP60), 3/4 (DSP75)

Motor full load .................................11.3A (DSP60), 11.8A (DSP75)

Liquid temperature range ...............40°F to 120°F

Max. operating position ..................45

o

from vertical

Dimensions .......................................14” x 12”

Intake ................................................2”

Discharge ..........................................2” NPT female

Power cord........................................16 gauge 3 conductor w/plug

Construction

Motor body material .......................Cold rolled steel
Motor housing .................................Cast iron
Volute ...............................................Cast iron
Impeller .............................................Cast iron
Seal plate ..........................................Cast iron
Shaft seal ..........................................Mechanical

GALLONS PER HOUR AT TOTAL HEAD IN FEET

Model

0’

5’

10’

15’

20’

25’

DSP60

8200

7500

6000

4000

2000

—

DSP75

8800

8160

7080

4920

2880

700

Performance

Sewage Pump

For parts, product & service information

visit

www.waynepumps.com