Vulcan K20ETT - Manual - manualsarea.com

Page 2 - IMPORTANT FOR YOUR SAFETY; IN THE EVENT OF A POWER FAILURE,

— 2 — ELECTRIC TILTING COUNTER KETTLES IMPORTANT FOR YOUR SAFETY THIS MANUAL HAS BEEN PREPARED FOR PERSONNEL QUALIFIED TOINSTALL ELECTRICAL EQUIPMENT, WHO SHOULD PERFORM THE INITIALFIELD START-UP AND ADJUSTMENTS OF THE EQUIPMENT COVERED BY THISMANUAL. Improper installation, adjustment, a l t e r a t...

Page 3 - TABLE OF CONTENTS

— 3 — ELECTRIC TILTING COUNTER KETTLES TABLE OF CONTENTS GENERAL ......................................................................................................................................... 4 Unpacking ........................................................................................

Page 4 - INSTALLATION, OPERATION AND MAINTENANCE OF; Fig. 1 K12ETT Electric Steam Kettle

— 4 — ELECTRIC TILTING COUNTER KETTLES INSTALLATION, OPERATION AND MAINTENANCE OF K6ETT, K12ETT, K20ETT ELECTRIC STEAM TILTING KETTLES SAVE THESE INSTRUCTIONS FOR FUTURE USE GENERAL Vulcan countertop tilting kettles are producedwith quality workmanship and material. Properinstallation, usage and mai...

Page 5 - U N P A C K I N G; LOCATION; INSTALLATION

— 5 — ELECTRIC TILTING COUNTER KETTLES Before installing, verify that the electrical supplyrequired for the equipment covered by thismanual agrees with the specifications on themachine data plate, located on the back of theunit. The data plate for the kettle is located onthe control box. If the elec...

Page 6 - Fig. 3 Mounting Hole Location

— 6 — ELECTRIC TILTING COUNTER KETTLES INSTALLING ELECTRIC KETTLE ONC O U N T E R Fig. 3 Mounting Hole Location 1. Position the kettle on the counter or stand in its final installed location with sufficientrear clearance (see Table 2 for minimumrequired clearance) from the wall to allowt h e k e t t...

Page 7 - The kettle and its parts are; Fig. 4 Rear of Kettle; OPERATION; ELECTRIC KETTLE OPERATION

— 7 — ELECTRIC TILTING COUNTER KETTLES The kettle and its parts are hot. Use care when operating, cleaning orservicing the kettle . VENTING While the kettle is cold, check the vacuum/pressure gauge. The gauge should be in thevacuum zone measuring between 25 to 30 in.Hg (84 to 100kPa). If not, there ...

Page 8 - TABLE 4. CONTROLS AND INDICATORS; Fig. 5 Kettle Controls

— 8 — ELECTRIC TILTING COUNTER KETTLES TABLE 4. CONTROLS AND INDICATORS Item Function Tilt Handle Tilts kettle. Power ON/OFF Switch Controls power to the kettle. Power ON Indicator (Amber) When lit, unit powered. Low Water Indicator (Red) When lit, indicates insufficient water in the kettle jacket. ...

Page 9 - MAINTENANCE; CLEANING

— 9 — ELECTRIC TILTING COUNTER KETTLES D i s c o n n e c te l e c t r i c a l power to the machine andf o l l o w L o c k o u t / T a g o u tprocedures before cleaning. NOTE: D o n o t h o s e d o w n u n d e r a n ycondition. Failure to comply will voidthe warranty. The kettle interior and exterior...

Page 10 - SYMPTOMS

— 10 — ELECTRIC TILTING COUNTER KETTLES SYMPTOMS POSSIBLE CAUSES/REMEDY Power switch not turned on/Turn on kettle power switch. Kettle unplugged/Plug kettle in. Breaker tripped or turned off/Reset or turn breaker on. Internal fuse failed/Call authorized servicer. Controls failure/Call authorized ser...

Page 11 - SERVICE AND PARTS INFORMATION

— 11 — ELECTRIC TILTING COUNTER KETTLES To obtain service and parts information concerning this model, contact the Vulcan-Hart ServiceAgency in your area (refer to our website, www.vulcanhart.com for a complete listing of AuthorizedService and Parts depots). When calling for service, the following i...

Vulcan K20ETT - Manual

Table of Contents:

Summary

Other Vulcan Models