Vulcan Fryers - Manual
Vulcan Fryers – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – PaSo; Programación en 7 Fáciles Pasos; guía dE conTroL Para ESTado SóLido; Freidora Vulcan
- Page 3 – Filtering; in 7 Easy Steps; SOLID STATE CONTROLS GUIDE; Vulcan Fryers; STEPS; v u l c a n; draiNiNg aNd discardiNg Oil
- Page 4 – FiltraciÓn; en 7 fáciles pasos; GUÍA DE CONTROL PARA ESTADO SÓLIDO; PASOS; cÓmO drENar y dEsEchar El acEiTE
STEP
Fill fry tank with oil and
then turn power on
1
STEP
Programming modES
2-7
www.VulcanHart.com • Fryer Technical Support: 1-800-814-2028
To SToP a TimEr oncE ThE counTdown SEquEncE haS STarTEd:
Press and hold the timer
button until timer is reset and
flashing light goes OFF.
LEFT TIMER
BUTTON
RIGHT TIMER
BUTTON
LEFT
RIGHT
LIGHTS
F-32912 (January 2007)
To
unLocK
this control you
must quickly press the
buttons while the
word ‘LocKEd’ is
displayed
LEFT LEFT righT righT
unLocK codE
Programming in 7 Easy Steps
(for revisions V3.00 or higher)
Display will scroll through VULCAN
➤
FRYERS
➤
Rev. No.
➤
MELT CYCLE LIQUID
SoLid STaTE conTroLS guidE
Vulcan
Fryers
TEMPERATURE SETTING
displays
Press
LEFT
to increase temp.
Press
RIGHT
to decrease temp.
Press
to go to Step 5.
RIGHT TIMER
displays
Press
LEFT
to increase time.
Press
RIGHT
to decrease time.
Press
to go to Step 4.
Display shows
ACTUAL TEMPERATURE
MELT CYCLE
displays
Press
LEFT
to change to
“S”
Solid.
Press
LEFT
to change to
NO MELT
.
Press
LEFT
to change to
“L”
Liquid.
Press
to go to Step 6.
Results of programming for
oil temperature is at set
temperature
TEMPERATURE
SETTING RESULTS
Press
program button
to enter the program mode:
LEFT TIMER
displays
Press
LEFT
to increase time.
Press
RIGHT
to decrease time.
Press
to go to Step 3.
Press
button and
HOLD
FOR 3-5 seconds
to save
and exit program mode.
Note: Programming modes can
be initiated while the fryer is
ON by pressing the
button.
If ‘LOCKED’ appears refer to
‘UNLOCK’ code.
UNLOCK
displays
Press
LEFT
to
LOCK
.
Press
RIGHT
to
UNLOCK
.
Press
to go to Step 7.
Note: VULCAN recommends
keeping the controls LOCKED after
programming to prevent altering
2
3
4
5
6
7
To make changes
to your program:
1. If display is
locked it must be
unlocked using the
unlock code.
2. After unlocking
go to steps
–
2
7
oPTionaL diSPLay modES
After the program mode is completed, one
of the following screens will be displayed.
Results of programming
MELT L
MELT CYCLE RESULTS
Display says
MELT L
Results of programming
MELT S
Display says
MELT S
Results of programming
NO MELT
Display says
HEATING
if oil
temperature is below 135 º F
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
PaSo Llenar el estanque para freir con aceite y después enciéndalo 1 PaSo modoS dE Programación 2-7 www.VulcanHart.com • Asistencia técnica para el freidor: 1-800-814-2028 Para dETEnEr EL TEmPoriZador una VEZ iniciada La SEcuEncia dE conTEo rEgrESiVo: Presione y mantenga presionado el botón del temp...
F-32914 (January 2007) www.VulcanHart.com • Fryer Technical Support: 1-800-814-2028 Filtering in 7 Easy Steps (for revisions V3.00 or higher) SOLID STATE CONTROLS GUIDE Vulcan Fryers STEPS 1- 3 STEPS 4-7 TIP: Use provided crumb scoop to remove and suspend crumbs on the bottom of tank before proceedi...
F-32914 (Enero 2007) www.VulcanHart.com • Asistencia técnica para el freidor: 1-800-814-2028 FiltraciÓn en 7 fáciles pasos (para las revisiones V3.00 o mayores) GUÍA DE CONTROL PARA ESTADO SÓLIDO Freidora Vulcan PASOS 1- 3 PASOS 4-7 CONSEJO: Use la pala para migajas que viene con el filtro para reti...
