VEVOR W88020160500FEFRXV1 - User Manual

4 DO NOT place anything heavy on top of hopper lid. It is not a shelf and is a tip hazard. Never use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter fluid, or similar liquids to start or ‘freshen up’ a fire in this appliance. Keep all such liquids well away from the appliance when i...

5 PELLET RESTRICTIONS This grill is designed for use of wood pellets only designed for burning in wood pellet grills. Do Not Use Pellet Fuel Labeled As Having Additives. We suggest that you use Z GRILLS BBQ WOOD PELLETS, which are specifically made to work in our grills. There is no guarantee that o...

6 COMPONENT LIST ITEM QTY DESCRIPTION ITEM QTY DESCRIPTION 1 1 Chimney Cap Assembly 25 1 Digital Control 2 1 Smoke Stack Assembly 26 1 Hopper Top Assembly I 3 1 Smoke Stack Gasket 27 1 Hopper Burner Lid 4 1 Grill Chamber Assembly 28 1 RTD Temperature Probe 5 1 Grease Bucket 29 1 Lid Handle 6 1 Right...

7 HARDWARE PACKAGE LIST ITEM QTY DESCRIPTION ITEM QTY DESCRIPTION A 29 Bolt 1/4-20×15.9 H 2 Cap Nut 5/16-18UNC B 5 Tapping Screw ST3.9*8mm I 2 Gasket (Ø8.5*Ø25*2.0mm) C 4 Bolt 5/32-32*9.5mm J 2 Gasket (Ø13*Ø25*2.0mm) D 4 Hexagon Bolt 1/4-20*15.9mm K 4 Gasket (Ø6.5*Ø18*2.0mm) E 2 Bolt 1/4-20*60 M 2 S...

8 ASSEMBLY INSTRUCTIONS PARTS DIAGRAM HOPPER BURNER ASSEMBLY

9 1.ASSEMBLING OF BOTTOM BASE 1.Push the Axle (11) through the wheel (12) 、 Gasket (J) and then through the hole in the legs (6)(13) as shown. The Gasket (I), Spring Washer (M), and Cap Nut (H) are used to secure the wheel assembly in place. Repeat for the other wheel. Press the Wheel Caps (9) firml...

12 Usage of Pellet Cleanout Door Note: The Hopper is equipped on the back with a Pellet Cleanout Door to clear the hopper of unused pellets so as to replace with fresh pellets or pellets of a different smoking flavor. 1. Place a bucket or bowl below cleanout door to capture falling pellets. 2. Turn ...

15 9.POSITIONING THE GREASE DRAIN PAN Position The Grease Drain Pan (18) over the Heat Baffle (17) by fitting over the bracket on the left side of grill wall. The notched leg of the Grease Drain Pan should be facing downward directly over the hole to the Grease Bucket to fit onto the locating bracke...

16 11.HANG ON THE GREASE BUCKET Locate the Grease Drain Tube which is on the right side of the chamber, then hang the Grease Bucket (5) on the hook.

17 INITIAL FIRING INSTRUCTIONS Please read this manual carefully and follow it step by step before starting your Z Grills for the first time and each time the grill runs out of pellets. 1.Remove the Porcelain Grills, Grease Drain Pan and Heat Baffle from the interior of the grill. 2.Open the Pellet ...

18 SUBSEQUENT START-UP ATTENTION: If the grill fails to light or the fire in the Firepot goes out while cooking, it is vital to follow these steps when sufficient pellets are still in the Pellet Hopper. Failure to follow the steps may cause a hazardous “ over-firing ” of your grill due to an excess ...

19 OPERATING TIPS 1.Like all grills, the actual temperature of this grill and the cooking times will be affected by external temperature, humidity, wind conditions, quality of pellets, etc. 2.It is beneficial to shelter your grill from the wind. This will aid in temperature output, heat retention an...

20 MAINTENANCE & CLEANING Your Z GRILL requires regular maintenance. Make sure your grill is OFF, unplugged and completely cold before performing any maintenance and cleaning. Grease 1.With regular use your grill will accumulate grease on the Flue Lining, the Grease Drain Tube, the V-shaped Grea...

21 Ash Clean the ash from the interior of the grill periodically. If excessive ash is in the firepot, it may cause the fire to go out. This is especially true in the SMOKE setting. A shop vac is an excellent tool to use for removing the ash. WARNING: MAKE SURE THE GRILL FIRE IS OUT, THE UNIT IS OFF,...

22 TROUBLESHOOTING CAUTION: Make sure the grill is completely cool and unplugged before you do any inspection, cleaning, maintenance or service work. Problem Potential Cause Solution Grill does not work properly Power Make sure the power cord is plugged in. Verify there is power at the electrical ou...

23 ERROR CODES LEr (Low Temperature Alarm )  Grill temperature was below 120 ℉ for more than 20 minutes. HEr (High Temperature Alarm )  Grill temperature reached 550 ℉ . Er 1  Ensure temperature probe is properly connected to the controller board. Er 2  Temperature dial security alarm. Turn the ...

24 DIGITAL THERMOSTAT CONTROL WIRING DIAGRAM Usage of the Meat Probe Put the plug of the Meat Probe into the control panel (PROBE1 or PROBE2) Insert the Probe into the food to measure the temperature The P1 temperature of the control panel is displayed as the temperature of PROBE1, while the P2 temp...

25 Z GRILLS SUPPORT Thank you for purchasing a Z GRILL! If you have any question, please contact customer support or your Z GRILL dealer. Z GRILLS, INC. offers the best technical and sales support in the industry. When calling customer please be prepared to provide the following information: 1.Deale...