Verizon Hotspot 890L - Manual

6 4. OK BUTTON  Confirm highlighted selection.  When the Jetpack button is locked, press once to light up the screen, and press again to unlock. 5. POWER SWITCH Power on/off your Jetpack.6. MICRO USB PORT Charge your Jetpack. 7. RESET BUTTON Press and hold to restore your Jetpack to the factory de...

8 Hardware Installation Installing the 4G SIM Card If you have not already done so, please follow these instructions for the installation of your new 4G SIM Card:1. Remove 4G SIM Card from the outer card, being careful not to touch the gold contacts. CAUTION : Do not bend or scratch your 4G SIM Card...

9 NOTE: Your 4G SIM (Subscriber Identity Module) Card is a small rectangular plastic card that stores your phone number and important information about your wireless service. The 4G SIM Card MUST remain in the Jetpack when in use. Inserting and Charging the Battery 1. Use the thumb catch at the bott...

11 Removing the 4G SIM Card 1. Turn the Verizon Jetpack power off. Remove the battery cover and take out the battery. 2. Gently remove the SIM Card from the SIM Card slot. N OT E : S h o u l d y o u r 4 G S I M C a r d b e l o s t o r damaged please call 1-800-922-0204 to speak with a Customer Servi...

12 Connecting to the Internet With your new Verizon Jetpack, a wireless Internet connection can always be at your fingertips. Connecting Wi-Fi Enabled Devices To Your Jetpack NOTE : It is recommended the battery be fully charged in order to use your Jetpack via Wi-Fi for the first time, or connect y...

13 Follow these Steps 1. Ensure the Wi-Fi enabled device you wish to connect to yourJetpack has Wi-Fi turned on, then use the Wi-Fi application toestablish a connection to your Jetpack. 2. Look for the network (SSID) named “ Verizon- 890L ”. There are XXXX digits unique to your device following the ...

14 Advanced Configuration 1. Make sure your computer is connected to the Jetpack . 2. L a u n c h t h e i n t e r n e t b r o w s e r a n d e n t e r http://192.168.1.1 or http://vz.hotspot in the address bar. NOTE : It is recommended that you use IE (7.0 or later), Firefox (3.0 or later), Opera (10...

15 PIN Code Verification If the PIN code of your SIM card is enabled, you will need to input the PIN code after you logging in. NOTE : The SIM card will be locked if you enter wrong PIN code consecutively for three times. If you want to change the PIN status or modify the PIN code, please select WAN...

16 Basic Setup After logging in, select Basic Setup > Quick Setup to configure the Wi-Fi settings, including Wi-Fi Network Name , Wi-Fi Securiy Policy and Sleep Time . Select Basic Setup > Password to change the login password for the Web User Interface.

17 WAN Settings After logging in, select WAN Settings > Wireless Info to display the infomation of WAN wireless. Click Refresh to update the information. Select WAN Settings > Network Select to select the proper network mode, including Global Mode , LTE/CDMA Mode , and GSM Mode(Automatic / Man...

20 Router After logging in, select Router > LAN to access the interface below: IP Address: IP address for LAN interface. Subnet Mask: Subnet mask for the IP address. MAC Address: MAC address for the LAN interface. D H C P S e r v e r : E n a b l e / d i s a b l e D H C P s e r v e r function. DHC...

22 Sleep Time: Set the time before the Jetpack enters sleep mode, The Jetpack will enter sleep mode if no Wi-Fi clients (devices) are connected to the Jetpack for a given period of time. Network Mode: If all of the wireless devices connect with the Jetpack in the same transmission mode, performance ...

25 to the Jetpack in order to connect to it. However, if the credentials are incorrect, data won't be transferred successfully between the WLAN clients and Jetpack. In effect, no authentication occurs. And in the SHARE authentication type, the WLAN client cannot connect to the Jetpack with the incor...

26 If the ACL( Access Control List ) policy is Deny , the user in MAC list can't connect to this device. If the ACL policy is Accept , the user in MAC list can connect to this device. You can allow or refuse a Wi-Fi user according to different ACL policy.Select Wi-Fi Settings > Firmware to displa...

29 IP Address: Set IP address for the virtual server. Port: Set port number for the virtual server. Protocol: Set the protocol for the virtual server. How to add a virtual server: 1. Select Enable and input the detailed information in the Virtual Server Settings area. 2. Click Apply to save your set...

31 Select Advanced > Config File to import/export the configuration file of the device. NOTE: It will modify the configuration of this device to import configuration file. Please make sure the parameters in the configuration file are correct. SMS This function allows you to view, save, send and r...

32 Navigating the Device Slide the Power Switch to the ON position to turn on the device. The screen lights up. After the initialization of the device, the SSID and default password will display on the screen. Press the OK button , the following icons will appear: NOTE : Devices and software are con...

34 Read the prompt on the display and refer to the Usage of WPS chapter. Settings Select using the UP and DOWN buttons and press the OK button to check the settings. Use the UP and DOWN buttons to scroll to the desired menu. Press the OK button to view information about the following settings: Devic...

36 Message Select using the UP and DOWN buttons and press the OK button to check messages. Select one of the following options: New Messages: Displays your unread messages. Inbox: Displays the messages in your inbox. Usage of WPS If your client device supports WPS, you need not input the password ma...

37 Glossary 3 G : Third Generation. 3G refers to the third generation of mobile telephony technology. 4G: Fourth Generation. 4G refers to the third generation of mobile telephony technology. 802.11(b, g, n): A set of WLAN communication standards in the 2.4, 3.6 and 5 GHz frequency bands. B r o a d b...

41 How to Get Help Assistance is at your fingertips at verizonwirless. com . Customer Service is at your disposal at 1 - 8 0 0 - 9 2 2 - 0 2 0 4 o r i n a n y Ve r i z o n W i r e l e s s Communications Store. If you have questions about how to use ZTE mobile devices or your device needs repair serv...

46  Stop using the battery if abnormal heat, odor, discoloration, deformation, or abnormal condition is detected during use, charge or storage.  Do not use your device with a damaged or deformed battery.  Do not solder the battery directly.  Remove the battery whose life cycle has expired from e...

52 While there may be differences between the SAR levels of various devices and at various positions, they all meet the government requirement. The FCC has granted an Equipment Authorization f o r t h i s d ev i c e w i t h a l l r e p o r t e d SA R l eve l s ev a l u a t e d a s i n c o m p l i a ...

55 Consumer Limited Warranty Z T E ( “ S e l l e r ” ) o f f e r s yo u a l i m i t e d w a r ra n t y t h a t t h e e n c l o s e d p r o d u c t o r p r o d u c t s ( t h e “Product”) will be free from defects in material and workmanship for a period that expires one year from the date of sale of ...

This Proof Indicates Approximate Color Only. For Accurate Color Match, Use Approved Color Standard. DO NOT USE COLOR FORMULAS ON THIS FILE. Inks THIS FILE MAY CONTAIN IMAGES OR ILLUSTRATIONS THAT ARE COPYRIGHT PROTECTED. CLIENT MUST OBTAIN PROPER LICENSING AND USAGE RIGHTS PRIOR TO REPRODUCTION. SUP...