Uniden UBC 61XLT – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
1
2
3
4
5
6
7
8
9
10
11
12
Table of Contents:
Page 2 – WARNING
Page 4 – SETUP; Installing the Batteries; Note: If you are installing alkaline batteries, set the; Optional Accessories; Cigarette Lighter Lead
Page 5 – Basic Operation; Think of Squelch Control as a gate. Turn; Turn SQUELCH fully clockwise until you hear a
Page 6 – ERROR
Page 7 – Channel Lockout
Page 8 – Priority Scan; Press again; P ch Loc Out
Page 9 – Chain Search; and
Page 11 – CAUTION
Page 12 – Troubleshooting; Problem; Warranty
Loading the manual
UBC
61XLT
Programmable
Hand-Held-
Scanner
MANUAL
OWNER’S
P r i n t e d i n t h e P h i l i p p i n e s
U B Z Z 0 1 2 9 6 F Z
UBC61 scanner Qk 3/12/02 11:22 AM Page 1
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Page 2 - WARNING
2 UBC 61 XLT Programmable Hand-Held Scanner Introduction What is Scanning?The UBC61XLT scans programmed channels untilit finds an active frequency. Scanning stops on an active frequency andremains on that channel as long as the transmis-sion continues. When the transmission ends, thescanning cycle r...
Page 4 - SETUP; Installing the Batteries; Note: If you are installing alkaline batteries, set the; Optional Accessories; Cigarette Lighter Lead
SETUP Installing the Batteries 1.Open the cover 2.Insert Batteries Note: If you are installing alkaline batteries, set the switch to REG. ALK.BATT. If installing nickel-cadmium batteries, set the switch to Ni-Cd BATT. 3.Replace cover and press down until it clicks into place. Do not mix alkalinebatt...
Page 5 - Basic Operation; Think of Squelch Control as a gate. Turn; Turn SQUELCH fully clockwise until you hear a
5 Basic Operation Setting the SquelchTo set the squelch, you must be in the manualmode.No signal should be present when adjustingsquelch. 1. Press until you do not hear a signal. 2. Adjust VOLUME to a comfortable listening level. 3. Think of Squelch Control as a gate. Turn SQUELCH fully counter-cloc...
Page 6 - ERROR
6 Programming Before the UBC61XLT can receive radio broad-casts, you must program a frequency into at leastone channel before scanning, repeat this procedurefor each channel you program.Up to 80 channels may be programmed 1. Select frequencies 2. Press 3. Select a channel a) Enter the channel number...
Page 7 - Channel Lockout
7 Channel Lockout You can lockout any channel so it is not reviewedduring normal scanning. You can restore the chan-nel to scanning whenever you wish. Lockout in Manual Mode1. Press 2. Select a channel a) Enter the channel number b) Then press again. 3. Press to lockout the channel. Locking a Channe...
Page 8 - Priority Scan; Press again; P ch Loc Out
8 3. Press to unlock the channel. Restore All Locked-out Channels1. Press You must be in manual mode before restoring all locked-out channels.2. Press and hold for about two seconds. You will hear twobeeps when all thechannels have beenrestored. Empty chan-nels cannotbe deleted and are alwayslocked ...
Page 9 - Chain Search; and
9 3. Press and hold for two seconds to desig-nate this channelas your new priority channel. Two beeps indicatethat the priority channel is changed. Chain Search Use chain search to find active frequencies in yourarea. You can search up to all five personal bandsor turn off those bands you don’t want...
Page 11 - CAUTION
11 1. Press either or during a search. You must bein search hold before restoring allskipped frequencies. 2. Press and hold for about two seconds. You will hear two beeps when all the frequencies have been restored. Storing Search FrequenciesYou can quickly store any frequency you find duringsearch....
Page 12 - Troubleshooting; Problem; Warranty
12 Troubleshooting If your UBC61XLT is not performing properly, try the following steps. Problem Suggestion Improper reception 1. Check the antenna connection or move and reposition the antenna.2. Move the scanner3. You may be in a remote area which could require an optional multiband antenna. Check...