Uniden BT230 - Manual - manualsarea.com

Page 2 - ConTenTs; GeTTinG To Know THe; pair the Headset to Your; UsinG THe MULTipoinT; pairing to More than; TroUBLesHooTinG and

2 ConTenTs GeTTinG To Know THe HeadseT .............................. 3 what the Led Colors Mean ....... 3 what the Buttons do ................. 5 seTTinG Up YoUr HeadseT .............................. 6 Charge the Battery .................... 6 pair the Headset to Your Bluetooth phone ................

Page 3 - GeTTinG To Know THe HeadseT; what the Led Colors Mean; Red

GeTTinG To Know THe HeadseT WARNING: Using the headset at excessive volume can cause permanent hearing loss. To reduce the risk of hearing damage, use the minimum volume level necessary (see page 13). * Specifications and features are subject to change without notice. what the Led Colors Mean Color ...

Page 4 - what the Tones Mean; Tone

Color State Meaning Blue flashes The headset is turned on. 1 flash every 5 seconds The headset is in standby & not paired to a Bluetooth device. 2 flashes every 5 seconds The headset is currently paired to a Bluetooth device. flashes every 5 seconds The headset is on an active call. Red & bl...

Page 5 - what the Buttons do

5 Tone Meaning 2 Rising Beeps Active call 2 Falling Beeps Ending a Call Short Beeps Successfully paired with a mobile phone what the Buttons do The headset initiates the function only after the button is released. Press it to Press & hold it for 2 seconds to 4 seconds to Multifunction button ( M...

Page 6 - seTTinG Up YoUr HeadseT; Charge the Battery

Press it to Press & hold it for 2 seconds to 4 seconds to Volume Up During a call: Increase the call volume. NA During a call-waiting call: Put the active call on hold and switch to the waiting call. Volume Down During a call: Decrease the call volume. NA NA seTTinG Up YoUr HeadseT Charge the Ba...

Page 7 - pair the Headset to Your Bluetooth phone; connect automatically whenever they can detect each other.

When the battery needs to be recharged, you will hear warning beeps every 0 seconds and see the red LED (depending on your headset status). NOTE: Use ONLY the AC adapter supplied with the headset. Using any other adapter could damage your headset, create a fire hazard, or cause a risk of electric sh...

Page 8 - pairing procedure again.; Connect to Your phone; additional Bluetooth information.; once the Headset is paired

Your phone should discover a device called a BT230 or BT230 headset , When your phone asks if you want to pair with this device, select yes. When your phone prompts you for a PIN code or password to pair with the BT20, enter 0000 . NOTE: If your phone supports Bluetooth 2.1, you do not need to enter...

Page 9 - it goes into idle mode. To manually reconnect, press; once. If the headset comes back in; UsinG YoUr HeadseT; Turning the; Slide the power button to its original position.; put your headset on; Insert the ear cushion, then wrap

If the headset loses the connection for more than 0 seconds (e.g., if your phone is out of range), it goes into idle mode. To manually reconnect, press MFB once. If the headset comes back in range in less than 0 seconds, it will automatically reconnect without pressing MFB. UsinG YoUr HeadseT Turnin...

Page 10 - wearing the Headset on Your Left ear; If you want to wear the headset on your left ear,; FeaTUres; Basic; After the headset is connected, you can use the following features:

10 comes in loud and clear. Move the headset around until you find the best angle for the ear cushion. wearing the Headset on Your Left ear If you want to wear the headset on your left ear, take the earhook off and turn it over. FeaTUres Basic After the headset is connected, you can use the followin...

Page 11 - Call waiting; your phone must support the hands-free profile.; until you; Up; again to switch back to the original call.); Voice-activated dialing; already be programmed.

11 Transfer a call Press and hold MFB for 2 seconds to transfer the current call from your phone to headset (and back). Redial the last number With the phone in standby, press MFB . The headset automatically dials the last number you dialed from your phone. Call waiting To use this feature, you must...

Page 12 - To deactivate voice dialing, press and hold; recording your voice tags through your headset. ); UsinG THe MULTipoinT FUnCTion; pairing to More than one phone; up, the headset automatically reconnects to the other phone.

12 To deactivate voice dialing, press and hold MFB until you hear a beep (about 2 seconds). NOTE: If you are in Voice Activated Dialing mode and you activate Last Number Redial, Voice- Activated Dialing turns off and the last number is dialed.Use your pre-programmed voice commands as you would with ...

Page 13 - answer the incoming call, press; for about 2 seconds.; TroUBLesHooTinG and MainTenanCe

1 Only one phone at a time can be on an active call.The headset plays a different ring tone for each phone so you know which one is ringing. To answer the incoming call, press MFB as usual. All the button functions remain the same for the first phone (the one you paired first). To use last number re...

Page 14 - reset the Headset; Press and hold; for seconds. The LED flashes 5 times and the; General InformatIon

1 If... Try... The headset paired with my phone, but I can’t hear anything through it. Making sure the call connected and is still active. Making sure the phone transferred the call to the headset. Press and hold MFB for two seconds to transfer the call. • • The headset keeps beeping, and I don’t kn...

Page 16 - cleaNiNg tHe HeadSet; importaNt SaFety iNStructioNS

If the noise continues, there may be interference on your phone itself, and any noise in the phone’s connection will come through on the headset, too. Transfer the call to your phone and see if the audio quality improves. If it doesn’t, look around for things that can interfere with your phone. Safe...

Page 17 - Fcc Notice

When using the headset, always follow basic safety precautions to reduce the risk of fire, electric shock and injury to persons, including the following: Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming poo...

Page 18 - two-year lImIted warranty

iNduStry caNada StatemeNt This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesir...

Uniden BT230 - Manual

Table of Contents:

Summary

Other Uniden Models