Page 4 - NOTE
Page 5 - Chapter 1: Introduction
5 Chapter 1: Introduction 1.1 - Congratulations You have purchased one of the most powerful server solutions. The Tempest i5000VS (S5372-LC) is a flexible Intel ® platform for multiple applications, based on Intel ® “Blackford-VS” MCH and ESB2 chipsets. Designed to support Intel ® Xeon 5100/5100-LV/...
Page 6 - Chapter 2: Board Installation
6 with one (1) inversed PCIe x4 slot (routed to PCIe x8 bus) • One (1) 32/33 PCI 2.3 slot • One (1) x8 PCI-E slot (with PCIe x4 bus) • One (1) Tyan TARO SO-DIMM socket Integrated I/O • One (1) IDE connector • Four (4) SATA ports • Four (4) USB 2.0 ports (2 at rear, 2 via cable) • Tyan 2x9 front-pane...
Page 7 - How to install our products right... the first time; (4) Place the motherboard on a grounded antistatic surface or on the
7 You are now ready to install your motherboard. The mounting hole pattern of the Tempest i5000VS S5372-LC matches the SSI CEB v1.01 specification. Before continuing with installation, confirm that your chassis supports an SSI CEB v1.01 motherboard. How to install our products right… the first time ...
Page 10 - – Jumper ON, with jumper cover
10 2.3 - Board Parts, Jumpers and Connectors This diagram is representative of the latest board revision available at the time of publishing. The board you receive may not look exactly like the above diagram. Jumper Legend OPEN - Jumper OFF, without jumper cover CLOSED – Jumper ON, with jumper...
Page 11 - Function
11 Jumper/Connector Function JP2/JP3 ASF1.0/SMDC Select Header JP4 Clear CMOS Jumper CN1/CN2 ATX Power Connectors CN4/CN8 CPU Fan Connectors (CN4: CPU0 Fan / CN8: CPU1 Fan) CN9/CN10/CN13/CN14 Chassis Fan Connectors (CN9: FAN2 / CN10: FAN1 CN13: FAN3 / CN14: FAN4) CN11 Tyan SO-DIMM Connector CN12 Fro...
Page 13 - JP4: Clear CMOS Jumper; Normal; Clear; Power off system and; disconnect power; Power on system
13 JP4: Clear CMOS Jumper 1 3 Normal (Default) 1 3 Clear Use this jumper when you forgot your system/setup password or need to clear system BIOS setting. How to clear the CMOS data - Power off system and disconnect power supply from AC source - Use jumper cap to close Pin_2 and 3 for several seconds...
Page 15 - Use this connector to connect the Tyan TARO card.
15 CN20: SMDC Connector The SMDC connector allows you to connect with Tyan Server Management Daughter Card (SMDC). The S5372-LC supports Tyan SMDC M3291. See Appendix I for more information on SMDC. CN11: Tyan SO-DIMM Connector Use this connector to connect the Tyan TARO card. CN19: Front Panel Head...
Page 18 - - Tips on Installing Motherboard in Chassis
18 2.4 - Tips on Installing Motherboard in Chassis Before installing your motherboard, make sure your chassis has the necessary motherboard support studs installed. These studs are usually metal and are gold in color. Usually, the chassis manufacturer will pre-install the support studs. If you are u...
Page 19 - WARNING
19 2.5 - Installing the Processor(s) Your Tempest i5000VS S5372-LC supports the latest processor technologies from Intel. Check the TYAN website for latest processor support: http://www.tyan.com Processor Installation The processor should be installed carefully. Make sure you are wearing an antistat...
Page 20 - Repeat this procedure for the second processor socket.
20 3. Lift the metal cover to expose the socket interior and place the socket in as shown. 4. Close the cover and return the locking lever to its locked position. 5. Repeat this procedure for the second processor socket. 6. Turn the board upside down and insert the heat sink spring mechanism as show...
Page 21 - CPU VRD Heat Dispersion Notice
21 8. Repeat this procedure for the second processor. Cooling Fan Installation After you have installed the processor, the heatsink should be installed to ensure that the processor runs efficiently and does not overheat. Use the heatsink supplied for best results. Follow these instructions to instal...
Page 22 - Memory Population Rules; Single Channel; X X
22 2.6 - Installing the Memory Before installing memory, ensure that the memory you have is compatible with the motherboard and processor. Only DDR2-667/533 Fully Buffer DIMM (FB DIMM) modules are required. Check the TYAN Web site at: www.tyan.com for details of the type of memory recommended for yo...
Page 23 - Memory Installation Procedure; : The S5372-LC only supports DDR2 Fully Buffered DIMM. Registered; NOT; Key slot
23 Memory Installation Procedure Follow these instructions to install memory modules into the Tempest i5000VS S5372-LC. 1. Press the locking levers in the direction shown in the following illustration. 2. Align the memory module with the socket. The memory module is keyed to fit only one way in the ...
Page 24 - : Always remember to properly set the drive jumpers. If only using
24 2.7 - Attaching Drive Cables Attaching IDE Drive Cable Attaching the IDE drive cable is simple. These cables are “keyed” to only allow them to be connected in the correct manner. TYAN motherboards have two on-board IDE channels, each supporting two drives. The black connector designates the Prima...
Page 26 - Installing Add-In Cards; PCI Express x8 Slot; unplug the power connector from the
26 2.8 - Installing Add-In Cards Before installing add-in cards, it’s helpful to know if they are fully compatible with your motherboard. For this reason, we’ve provided the diagrams below, showing the slots that appear on your motherboard. PC I-X (64 / 1 3 3) PCI Express x8 Slot PCI Sl ot P C I E x...
Page 28 - not; compatible with the board; Applying power to the board; unplug the power supply before plugging the power cables; calling your vendor’s support line.
28 2.10 - Installing the Power Supply There are two power connectors on your Tempest i5000VS S5372-LC. The Tempest i5000VS S5372-LC requires that you have an EPS12V power supply that has a 24-pin and an 8-pin power connector. Please be aware that ATX 2.x, ATX12V and ATXGES power supplies may not be ...
Page 29 - Chapter 3: BIOS Setup; Key
29 Chapter 3: BIOS Setup 3.1. About the BIOS The BIOS is the basic input/output system, the firmware on the motherboard that enables your hardware to interface with your software. The BIOS determines what a computer can do without accessing programs from a disk. The BIOS contains all the code requir...
Page 31 - Main; Esc; System Time / Date setup
31 3.2 BIOS Main Menu In this section, you can alter general features such as the date and time, as well as access to the IDE configuration options. Note that the options listed below are for options that can directly be changed within the Main Setup screen. PhoenixBIOS Setup Utility Main Advanced S...
Page 32 - Selects the type of device connected to the system.
32 3.2.1 IDE Channel 0/Secondary//Master/Slave Setup Computer detects IDE drive type from drive C to drive F. Press Enter on any of the Channel 0/Master, Channel 0/Slave, Secondary/Master, Secondary/Slave options to view advanced details of the corresponding drive. The system displays advanced detai...
Page 34 - Cache System BIOS Area
34 3.2.2 Memory Cache This setting allows you to tweak the various cache settings for optimal performance of your system. Press Enter to display the various cache settings. PhoenixBIOS Setup Utility Main Advanced Security Power Boot Exit Memory Cache Item Specific Help Cache System BIOS area: Cache ...
Page 35 - This feature allows you to control caching of 512K base memory.
35 As such, it would be a waste of L2 cache bandwidth to cache the video BIOS instead of data that are more critical to the system's performance. In addition, if any program writes into this memory area, it will result in a system crash. So, it is recommended that you write protect this area for opt...
Page 36 - Spin up the hard disks as soon as power is supplied (or as soon as
36 3.2.3 Boot Features This option allows setting boot parameters. Press Enter to view the Boot Features screen. PhoenixBIOS Setup Utility Main Advanced Security Power Boot Exit Boot Features Item Specific Help : Keyboard Error Report Summery screen: Boot-time Diagnostic Screen: QuickBoot Mode: Exte...
Page 37 - Enabled
37 Initialize only critical parts of the chipset Read memory size from the SPD (Serial Presence Detect) chip on the memory modules Eliminate logo delays If disabled, the BIOS will run the whole gamut of boot-up tests. It is recommended that you disable this feature when you boot up a new computer fo...
Page 38 - Advanced; Installed OS; Select the operating system installed on the PC.; : An incorrect setting can cause the operating system to display; Reset Configuration Data
38 3.3 Advanced Menu This section facilitates configuring advanced BIOS options for your system. PhoenixBIOS Setup Utility Main Advanced Security Power Boot Exit Item Specific Help Installed O/S: Reset Configuration Data: Large Disk Access Mode: X Advanced Chipset Control X Advanced Processor Option...
Page 40 - Crystal Beach Configure Enable; Select ECC error conditions that SERR# be asserted.; Single bit; This option is used to determine the frequency at PCI-X bus.; Auto
40 3.3.1 Advanced Chipset Control This section allows you to fine tune the chipset configuration. PhoenixBIOS Setup Utility Main Advanced Security Power Boot Exit Advanced Chipset Control Item Specific Help X ICH USB Control Sub-Menu X Slot PCI-E (x4 Port) Sub-Menu X Slot PCI-E (x8 Port) Sub-Menu X ...
Page 42 - These items are used to control the various ICH USB devices.; Control USB 2.0 functionality through this Setup Item.
42 Native Mode Operation This feature is used to choose Native Mode for ATA. However, certain OS is not supported under Native Mode. Auto / Serial ATA SATA Controller Mode Option This feature is used to select SATA controller mode. In “compatible mode”, SATA and PATA drives are auto-detected and pla...
Page 43 - These items are used for PCI Express Port control options.
43 3.3.1.2 Slot PCI-E (x4 Port) Sub-Menu These items are used for PCI Express Root Port #1 control options. PhoenixBIOS Setup Utility Main Advanced Security Power Boot Exit Slot PCI-E (x4 Port) Sub-Menu Item Specific Help PCI-E Port 1 Port #1 Enabled Port #1 Width Port #1 Slot Card Detech [Auto] = Y...
Page 44 - This option allows you to initialize the device expansion ROM.; Disabled
44 3.3.1.4 A Lan Control Sub-Menu These items allow you to control the LAN devices. PhoenixBIOS Setup Utility Main Advanced Security Power Boot Exit LAN Control Sub-Menu Item Specific Help LAN1 (Gilgal) Option ROM Scan: LAN2 (Gilgal) Option ROM Scan: [Enabled] [Disabled] [Enabled] [Disabled] F1 Help...
Page 45 - Hyperthreading (Available depending on CPU); This feature is used to enable the Vanderpool technology.
45 3.3.2 Advanced Processor Options This section allows you to fine-tune the processor options. PhoenixBIOS Setup Utility Main Advanced Security Power Boot Exit Advanced Processor Options Item Specific Help Hyperthreading: Intel® Virtualization Technology C1 Enhanced Mode Execute Disable Bit Set Max...
Page 47 - This defines how the first serial port is detected and configured.; Temp 1 is controlled by SMSC SCH5017. Temp 2 is controlled by
47 Serial Port A: This defines how the first serial port is detected and configured. Auto/ Enabled / Disabled 3.3.4 Hardware Monitor Configuration This displays critical system parameters like CPU speed, fan speeds, voltage levels and CPU temperature. PhoenixBIOS Setup Utility Main Advanced Security...
Page 49 - If enabled it will use a port on the motherboard.
49 3.3.5 Console Redirection PhoenixBIOS Setup Utility Main Advanced Security Power Boot Exit Console Redirection Item Specific Help Com Port Address Baud Rate Console Type Flow Control Console connection: Continue C. R. after POST: [Disabled] [19.2K] [VT 100] [None] [Direct] [Off] F1 Help ↑↓ Select...
Page 50 - Security; The system displays the current supervisor and user passwords.; Set Supervisor Password
50 3.4 Security These settings allow you to configure the security options for your system. PhoenixBIOS Setup Utility Main Advanced Security Power Boot Exit Item Specific Help Supervisor Password Is: User Password Is: Set Supervisor Password Set User Password Password on boot: Clear Clear [Enter] [E...
Page 51 - Power
51 3.5 Power These settings allow you to configure the power options for your system. PhoenixBIOS Setup Utility Main Advanced Security Power Boot Exit Item Specific Help Resume On Time: Resume Time: Power On By PCI/PCI-X Chassis Intrusion Detect: After Power Failure: [Off] [xx:xx:xx] [Disabled] [No]...
Page 52 - Boot
52 3.6 Boot Menu Use this screen to select options for the Boot Settings Configuration. PhoenixBIOS Setup Utility Main Advanced Security Power Boot Exit Item Specific Help 1: 2: 3: 4: 5: 6: 7: 8: : Legacy Network Card ; Bootable Add-in Cards Keys used to view or configure devices: <Enter> expa...
Page 53 - Exit; Exit Saving Changes
53 3.7 Exit Menu These settings set the exit options on your system. PhoenixBIOS Setup Utility Main Advanced Security Power Boot Exit Item Specific Help Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes Exit system Setup and save your changes to CMOS. F1 He...
Page 55 - Chapter 4: Diagnostics; A single long beep followed by two short beeps: It indicates that a; Note
55 Chapter 4: Diagnostics NOTE: If you experience problems with setting up your system, always check the following things in the following order: Memory, Video, CPU By checking these items, you will most likely find out what the problem might have been when setting up your system. For more informati...
Page 59 - Appendix I: SMDC Information; monitor; and; diagnose; activities effectively.
59 Appendix I: SMDC Information Overview Tyan Server Management Daughter Card (SMDC) is a powerful yet cost-efficient solution for high-end server management hardware packages. Tyan’s goal is to provide remote system monitoring and control even when the operating system is absence or simply fails. T...
Page 60 - Features of Tyan Server Management; Remote power on and power off
60 Features of Tyan Server Management Monitor various system components remotely - such as fans, processor temperature, and more Remote power on and power off Console redirect -the ability to view system remotely Alert and error actions -such as audible beep, e-mail, power down and reboot SMDC runs ...
Page 61 - Appendix II: How to Make a Driver Diskette; TYAN Driver Diskette Maker V1.0
61 Appendix II: How to Make a Driver Diskette Follow the steps below to make a driver diskette from the TYAN driver CD provided. 1. Start the system and insert the TYAN CD into the CD-ROM drive to boot from CD. You will see the following menu. Then press [1] and [Enter] to boot the system to Tyan di...
Page 62 - Intel Chipset Model; TYAN Driver Diskette Maker; Microsoft Windows XP 32-bit
62 3. The following picture pops up after selecting the chipset model. TYAN Driver Diskette Maker ** Example Vendor** ====Choose Chipset Model==== 01 Intel Chipset Model EXIT 4. After selecting the chipset model, select the OS to start the diskette making. TYAN Driver Diskette Maker ====Example Chip...
Page 63 - Glossary; a power management
63 Glossary ACPI (Advanced Configuration and Power Interface): a power management specification that allows the operating system to control the amount of power distributed to the computer’s devices. Devices not in use can be turned off, reducing unnecessary power expenditure. AGP (Accelerated Graphi...
Page 64 - Closed and open jumpers:
64 Bus: a data pathway. The term is used especially to refer to the connection between the processor and system memory, and between the processor and PCI or ISA local buses. Bus mastering: allows peripheral devices and IDEs to access the system memory without going through the CPU (similar to DMA ch...
Page 65 - ECC (Error Correction Code or Error Checking and Correcting):
65 IRQs, it is vital that you do not double up devices on a single line. Plug-n-Play devices will take care of this for you. Doze mode: in this mode, only the CPU’s speed is slowed. DRAM (Dynamic RAM): widely available, very affordable form of RAM which has the unfortunate tendency to lose data if i...
Page 70 - Returning Merchandise for Service
70 Technical Support If a problem arises with your system, you should turn to your dealer for help first. Your system has most likely been configured by them, and they should have the best idea of what hardware and software your system contains. Furthermore, if you purchased your system from a deale...